Page 649 of 2896
BL-160
INTELLIGENT KEY SYSTEM
Revision: June 20062007 Versa
Removal and Installation of Intelligent Key UnitEIS0092V
REMOVAL
1. Remove glove box assembly. Refer to IP-11, "Removal and Installation" .
2. Disconnect Intelligent Key unit connector, remove screw and
Intelligent Key unit.
INSTALLATION
Installation is in the reverse order of removal.
PIIB6534E
Page 650 of 2896
DOOR
BL-161
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
DOORPFP:80100
Fitting AdjustmentEIS0092X
FRONT DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End
Access from inside the fender to loosen the hinge bolts. Raise the front door at rear end to adjust.
Surface Height Adjustment
Loosen the front door bolts, and adjust the surface height difference of fender and front door according to the
fitting standard dimension.
1. Front fender 2. Front door outer 3. Rear door outer
4. Rear fender 5. Front door weatherstrip 6. Front door sash
7. Rear door weatherstrip 8. Rear door sash
PIIB6516E
Page 651 of 2896
BL-162
DOOR
Revision: June 20062007 Versa
Striker Adjustment1.
16.7 N·m (1.7 kg-m, 12 ft-lb)
PIIB2804J
Page 652 of 2896
DOOR
BL-163
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
REAR DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End
1. Remove the center pillar upper and lower garnishes. Refer to EI-32, "BODY SIDE TRIM" .
2. Access from inside the vehicle to loosen the hinge nuts. Open the rear door, and raise the rear door at
rear end to adjust.
Surface Height Adjustment
Loosen the front door striker bolts and rear door hinge nuts, and adjust the surface height difference of front
and rear doors according to the fitting standard dimension.
Striker Adjustment1.
16.7 N·m (1.7 kg-m, 12 ft-lb)
PIIB2804J
Page 653 of 2896
BL-164
DOOR
Revision: June 20062007 Versa
BACK DOOR
Longitudinal Clearance and Surface Height Adjustment
1. Open and support the back door.
2. Slightly loosen the hinge nuts.
3. Reposition the door as necessary and tighten the nuts.
4. Confirm the adjustment. Repeat as necessary to obtain the desired fit.
1. Back door assembly 2. Back door hinge 3. Tail lamp assembly
4. Back window glass 5. Roof 6. Rear pillar
A. 6.0 ± 1.0 mm (0.24 ± 0.04 in) B. -0.5 ± 1.0 mm (-0.02 ± 0.04 in) C. 5.0 ± 1.2 mm (0.20 ± 0.05 in)
D. 0.0 ± 1.5 mm (0.0 ± 0.06 in) E. 5.0 ± 2.3 mm ( 0.20 ± 0.9 in) F. 2.7 +1.6 -2.1 mm (0.11 + 0.06 - 0.08 in)
G. 5 . 0 ± 1.2 mm ( 0.20 ± 0.05 in) H. 0.0 ± 1.5 mm (0.0 ± 0.06 in)
LIIA2668E
Page 654 of 2896

DOOR
BL-165
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
Striker Adjustment1.
Removal and InstallationEIS009C1
FRONT DOOR
CAUTION:
When removing and installing the front door assembly, support the door with a jack and cloth to
protect the door and body.
When removing and installing front door assembly, be sure to carry out the fitting adjustment.
Refer to BL-161, "
Fitting Adjustment" .
After installing, apply touch-up paint onto the head of the hinge nuts.
Check the hinge rotating part for lubrication. If necessary, apply “body grease”.
Operate with two workers, because of its heavy weight.
Check front door open/close operation after installation.
Removal
1. Remove dash side finisher. Refer to EI-32, "Removal and Installation" .
2. Disconnect the front door harness connectors.
3. Remove the front door harness grommet, and then remove the
harness from the vehicle.
4. Remove the check link bolt.20 N·m (2.2 kg-m, 16 ft-lb)
LIIA2641E
PIIB6518E
14.7 N·m (1.5 kg-m, 11 ft-lb)
PIIB6543E
Page 655 of 2896
BL-166
DOOR
Revision: June 20062007 Versa
5. Remove the hinge nuts and then the door assembly.
Installation
Installation is in the reverse order of removal.
REAR DOOR
CAUTION:
When removing and installing the rear door assembly, support the door with a jack and cloth to
protect the door and body.
When removing and installing rear door assembly, be sure to carry out the fitting adjustment.
Refer to BL-161, "
Fitting Adjustment" .
After installing, apply touch-up paint onto the head of the hinge nuts.
Check the hinge rotating part for poor lubrication. If necessary, apply “body grease”.
Operate with two workers, because of its heavy weight.
Check rear door open/close operation after installation.
Removal
1. Remove the rear door harness grommet.
2. Disconnect the rear door harness connector. 24.5 N·m (2.5 kg-m, 18 ft-lb)
PIIB6519E
PIIB6520E
PIIB6521E
Page 656 of 2896
DOOR
BL-167
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
3. Remove the check link bolt.
4. Remove the hinge nuts and the door assembly.
Installation
Installation is in the reverse order of removal.
BACK DOOR
Removal
1. Remove the back door glass. Refer toGW-15, "REAR WINDOW GLASS AND MOLDING" .
2. Remove the back door lock assembly. Refer to BL-175, "
BACK DOOR LOCK" .
3. Remove the back door wire harness.
4. Remove the rear washer nozzle and hose from the back door. Refer to WW-42, "
REAR WASHER NOZ-
ZLE" .
5. Support the back door.
CAUTION:
Two technicians should be used to avoid damaging the back door during removal.
6. Remove the back door stays.
7. Remove the door side nuts and the back door assembly. 14.7 N·m (1.5 kg-m, 11 ft-lb)
PIIB6543E
24.5 N·m (2.5 kg-m, 18 ft-lb)
PIIB6522E
LIIA2639E