Page 57 of 2896

AT-44
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
Shift Solenoid Valve A and B
If non-standard solenoid signal is sent to TCM, use of certain gears is limited. Refer to chart shown below.
: Solenoid ON
×: Solenoid OFF
–: Non-standard condition
Line Pressure Solenoid Valve
If non-standard solenoid signal is sent to TCM, line pressure solenoid valve is turned OFF to achieve maxi-
mum oil pressure.
Torque Converter Clutch Solenoid Valve
If non-standard solenoid signal is sent to TCM, torque converter clutch solenoid valve is turned OFF to release
lock-up.
Overrun Clutch Solenoid Valve
If non-standard solenoid signal is sent to TCM, overrun clutch solenoid valve is turned OFF to engage overrun
clutch. This will result in more effective engine brake during deceleration.
Shift positionNormalMalfunction in solenoid
valve AMalfunction in solenoid
valve BMalfunction in solenoid
valves A and B
A B Gear A B Gear A B Gear A B Gear
“D” position1st –→×
3rd →×–
3rd ––
3rd ×2nd –→× ×–––
××3rd – x×–––
×4th – x→×–––
“2” position1st –→×→×–––
×2nd –→× ×–––
××3rd – x×–––
“1” position1st –→×→×–––
×2nd –→× ×–––
××3rd – x×–––
Page 58 of 2896

TROUBLE DIAGNOSIS
AT-45
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
How to Perform Trouble Diagnoses for Quick and Accurate RepairUCS005M N
INTRODUCTION
The TCM receives a signal from the vehicle speed sensor, accelera-
tor pedal position sensor or PNP switch and provides shift control or
lock-up control via A/T solenoid valves.
The TCM also communicates with the ECM by means of a sig-
nalsent from sensing elements used with the OBD-related parts of
theA/T system for malfunction-diagnostic purposes. The TCM is
capa-ble of diagnosing malfunctioning parts while the ECM can store
mal-functions in its memory.
Input and output signals must always be correct and stable in the
operation of the A/T system. The A/T system must be in good oper-
ating condition and be free of valve seizure, solenoid valve malfunc-
tion, etc.
It is much more difficult to diagnose a malfunction that occurs intermittently rather than continuously. Most
intermittent malfunctions are caused by poor electric connections or improper wiring. In this case, careful
checking of suspected circuits may help prevent the replacement of good parts.
A visual check only, may not find the cause of the malfunctions. A
road test with CONSULT-II or a circuit tester connected should be
performed. Follow the AT-46, "
WORK FLOW" .
Before undertaking actual checks, take a few minutes to talk with a
customer who approaches with a driveability complaint. The cus-
tomer can supply good information about such malfunctions, espe-
cially intermittent ones. Find out what symptoms are present and
under what conditions they occur. A “DIAGNOSTIC WORKSHEET”
like the example (AT- 4 7 , "
DIAGNOSTIC WORKSHEET" ) should be
used.
Start your diagnosis by looking for “conventional” malfunctions first.
This will help troubleshoot driveability malfunctions on an electroni-
cally controlled engine vehicle.
Also check related Service bulletins for information.
SAT6 3 1IA
SAT6 3 2I
SEF 2 34 G
Page 59 of 2896
AT-46
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
WORK FLOW
A good understanding of the malfunction conditions can make troubleshooting faster and more accurate. In
general, each customer feels differently about a malfunction. It is important to fully understand the symptoms
or conditions for a customer complaint.
Make good use of the two sheets provided, AT - 4 7 , "
Information from Customer" and AT- 4 7 , "Diagnostic Work-
sheet Chart" , to perform the best troubleshooting possible.
Work Flow Chart
*1AT- 4 7*2AT- 4 7*3AT - 4 3
*4AT- 5 3*5AT- 5 3, AT-5 6*6AT - 5 8
*7AT- 8 2*8AT- 3 9*9AT - 4 3
*10AT- 1 0 7*11AT- 1 8 2*12AT - 1 9 3
*13AT- 6 8*14AT- 8 3*15AT - 9 4
*16AT- 1 8 2*17EC-48
SCIA7146E
Page 60 of 2896

TROUBLE DIAGNOSIS
AT-47
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
DIAGNOSTIC WORKSHEET
Information from Customer
KEY POINTS
WHAT..... Vehicle & A/T model
WHEN..... Date, Frequencies
WHERE..... Road conditions
HOW..... Operating conditions, Symptoms
Diagnostic Worksheet Chart
Customer name MR./MS Model & Year VIN
Trans. model Engine Mileage
Incident Date Manuf. Date In Service Date
Frequency❏ Continuous❏ Intermittent ( times a day)
Symptoms❏ Vehicle does not move. (❏ Any position❏ Particular position)
❏ No up-shift (❏ 1st → 2nd❏ 2nd → 3rd❏ 3rd → 4th)
❏ No down-shift (❏ 4th → 3rd❏ 3rd → 2nd❏ 2nd → 1st)
❏ Lock-up malfunction
❏ Shift point too high or too low.
❏ Shift shock or slip (❏ N → D❏ Lock-up❏ Any drive position)
❏ Noise or vibration
❏ No kick down
❏ No pattern select
❏ Others
()
1.❏ Read the Fail-safe and listen to customer complaints.AT-4 3,
AT-4 7
2.❏ Check A/T fluidAT-1 6
❏ Leakage (Follow specified procedure)
❏ Fluid condition
❏ Fluid level
3.❏ Perform “STALL TEST” and “LINE PRESSURE TEST”.AT-5 3
,
AT-5 6
❏ “STALL TEST” — Mark possible damaged components/others.
❏ Torque converter one-way clutch
❏ Reverse clutch
❏ Forward clutch
❏ Overrun clutch
❏ Forward one-way clutch❏ Low & reverse brake
❏ Low one-way clutch
❏ Engine
❏ Line pressure is low
❏ Clutches and brakes except high clutch and
brake band are OK
❏ “LINE PRESSURE TEST” — Suspected parts:
Page 61 of 2896

AT-48
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
4.❏ Perform “Road Test”.AT- 5 8
4-1. “Check Before Engine is Started”AT- 5 8
❏ AT-198, "OD OFF Indicator Lamp Does Not Come On"
❏ Perform self-diagnosis. Enter checks for detected items. AT- 8 2 , AT- 9 0 .
❏ AT- 9 4 , "
DTC U1000 CAN COMMUNICATION LINE" .
❏ AT- 9 7 , "
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH" .
❏ AT-102, "
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT" .
❏ AT-107, "
DTC P0720 VEHICLE SPEED SENSOR·A/T (REVOLUTION SENSOR)" .
❏ AT- 11 3 , "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT- 11 7 , "
DTC P0731 A/T 1ST GEAR FUNCTION"
❏ AT-121, "DTC P0732 A/T 2ND GEAR FUNCTION" .
❏ AT-124, "
DTC P0733 A/T 3RD GEAR FUNCTION" .
❏ AT-128, "
DTC P0734 A/T 4TH GEAR FUNCTION" .
❏ AT-134, "
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
❏ AT-139, "
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" .
❏ AT-145, "
DTC P0745 LINE PRESSURE SOLENOID VALVE" .
❏ AT-151, "
DTC P0750 SHIFT SOLENOID VALVE A" .
❏ AT-156, "
DTC P0755 SHIFT SOLENOID VALVE B" .
❏ AT-161, "
DTC P1760 OVERRUN CLUTCH SOLENOID VALVE" .
❏ AT-166, "
DTC VEHICLE SPEED SENSOR MTR" .
❏ AT-170, "
DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM
POWER SOURCE)" .
❏ AT-176, "
DTC TURBINE REVOLUTION SENSOR" .
❏ AT-182, "
CONTROL UNIT (RAM), CONTROL UNIT (ROM)" .
❏ AT-183, "
MAIN POWER SUPPLY AND GROUND CIRCUIT" .
4-2. “Check at Idle”AT- 5 9
❏ AT-200, "Engine Cannot Be Started in “P” and “N” Position" .
❏ AT-201, "
In “P” Position, Vehicle Moves Forward or Backward When Pushed" .
❏ AT-201, "
In “N” Position, Vehicle Moves" .
❏ AT-202, "
Large Shock “N” → “R” Position" .
❏ AT-203, "
Vehicle Does Not Creep Backward in “R” Position" .
❏ AT-205, "
Vehicle Does Not Creep Forward in “D”, “2” or “1” Position" .
Page 62 of 2896

TROUBLE DIAGNOSIS
AT-49
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
4. 4-3. “Cruise Test”AT-6 1
Part 1
❏ AT-206, "
Vehicle Cannot Be Started from D1" .
❏ AT-208, "
A/T Does Not Shift: D1 → D2 or Does Not Kickdown: D4 → D2" .
❏ AT-210, "
A/T Does Not Shift: D2 → D3" .
❏ AT-212, "
A/T Does Not Shift: D3 → D4" .
❏ AT-214, "
A/T Does Not Perform Lock-up" .
❏ AT-215, "
A/T Does Not Hold Lock-up Condition" .
❏ AT-216, "
Lock-up Is Not Released" .
❏ AT-217, "
Engine Speed Does Not Return to Idle (Light Braking D4 → D3 )" .
Part 2AT-6 4
❏ AT-206, "Vehicle Cannot Be Started from D1" .
❏ AT-208, "
A/T Does Not Shift: D1 → D2 or Does Not Kickdown: D4 → D2" .
❏ AT-210, "
A/T Does Not Shift: D2 → D3" .
❏ AT-212, "
A/T Does Not Shift: D3 → D4" .
Part 3AT-6 5
❏ AT-218, "A/T Does Not Shift: D4 → D3 , When OD OFF" .
❏ AT-219, "
A/T Does Not Shift: D3 → 22 , When Selector Lever “D” → “2” Position" .
❏ AT-221, "
A/T Does Not Shift: 22 → 11 , When Selector Lever “2” → “1” Position" .
❏ AT-223, "
Vehicle Does Not Decelerate by Engine Brake" .
❏ Perform self-diagnosis. Enter checks for detected items. AT-8 2
, AT-9 0 .
❏ AT - 9 4 , "
DTC U1000 CAN COMMUNICATION LINE" .
❏ AT - 9 7 , "
DTC P0705 PARK/NEUTRAL POSITION (PNP) SWITCH" .
❏ AT-102, "
DTC P0710 A/T FLUID TEMPERATURE SENSOR CIRCUIT" .
❏ AT-107, "
DTC P0720 VEHICLE SPEED SENSOR·A/T (REVOLUTION SENSOR)" .
❏ AT - 11 3 , "
DTC P0725 ENGINE SPEED SIGNAL" .
❏ AT - 11 7 , "
DTC P0731 A/T 1ST GEAR FUNCTION"
❏ AT-121, "DTC P0732 A/T 2ND GEAR FUNCTION" .
❏ AT-124, "
DTC P0733 A/T 3RD GEAR FUNCTION" .
❏ AT-128, "
DTC P0734 A/T 4TH GEAR FUNCTION" .
❏ AT-134, "
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE" .
❏ AT-139, "
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)" .
❏ AT-145, "
DTC P0745 LINE PRESSURE SOLENOID VALVE" .
❏ AT-151, "
DTC P0750 SHIFT SOLENOID VALVE A" .
❏ AT-156, "
DTC P0755 SHIFT SOLENOID VALVE B" .
❏ AT-161, "
DTC P1760 OVERRUN CLUTCH SOLENOID VALVE" .
❏ AT-166, "
DTC VEHICLE SPEED SENSOR MTR" .
❏ AT-170, "
DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM
POWER SOURCE)" .
❏ AT-176, "
DTC TURBINE REVOLUTION SENSOR" .
❏ AT-182, "
CONTROL UNIT (RAM), CONTROL UNIT (ROM)" .
❏ AT-183, "
MAIN POWER SUPPLY AND GROUND CIRCUIT" .
5.❏ For self-diagnosis NG items, inspect each component. Repair or replace the damaged parts.AT-8 2
,
AT-9 1
6.❏ Perform “Road Test”.AT-5 8
7.❏ Perform the Diagnostic Procedures for all remaining items marked NG. Repair or replace the damaged parts.
Refer to the Symptom Chart when you perform the procedures. (The chart also shows some other possible
symptoms and the component inspection orders.)AT-6 8
8.❏ Erase DTC from TCM and ECM memories.AT-8 3,
AT-9 3
Page 63 of 2896
AT-50
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
A/T Electrical Parts LocationUCS005MO
BCIA0037E
Page 64 of 2896
TROUBLE DIAGNOSIS
AT-51
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: June 20062007 Versa
1. OD OFF indicator lamp 2. Shift position indicator 3. Accelerator pedal position (APP)
sensor
4. Turbine revolution sensor (Power
train revolution sensor)5. PNP switch 6. Terminal body (Terminal cord
assembly connector)
7. Revolution sensor 8. Dropping resistor 9. TCM
10. Overdrive control switch