Page 2121 of 2896
INSTRUMENT PANEL ASSEMBLY
IP-21
C
D
E
F
G
H
J
K
L
MA
B
IP
Revision: June 20062007 Versa
17. Remove screws (A) and metal clip (B), and remove combination
meter.
Installation
Installation is in the reverse order of removal.
GLOVE BOX ASSEMBLY
Removal
1. Remove glove box screws.
2. Pull backward while disengaging the glove box assembly pawls.
3. Disconnect lamp harness connector, and then remove glove box
assembly.
Installation
Installation is in the reverse order of removal.
INSTRUMENT LOWER FINISHER
Removal
1. Pull backward while disengage the instrument lower finisher's
clip and pawls.
2. Disconnect in-vehicle sensor and harness connector, and then
remove instrument lower finisher.
Installation
Installation is in the reverse order of removal.
PKIC0703E
PIIB3404E
LIIA2544E
Page 2122 of 2896

IP-22
INSTRUMENT PANEL ASSEMBLY
Revision: June 20062007 Versa
CENTER CONSOLE ASSEMBLY
Removal
1. Insert a suitable tool into front side space of console mask, and
disengage metal clips.
2. Disconnect harness connector, and then remove console mask.
3. Place the selector lever in "D" position (A/T and CVT only).
4. Remove selector lever knob (A/T and CVT only). Refer to CVT-
191, "Removal and Installation" (CVT), AT-229, "Control Device
Removal and Installation" (A/T).
5. Pull up and disengage A/T and CVT console finisher metal clips
(A/T and CVT only).
6. Remove A/T and CVT console finisher (A/T and CVT only).
7. Remove shift knob (M/T only). Refer to MT-48, "
SHIFT CONTROL" .
8. Pull up and disengage M/T console boot metal clips (M/T only).
9. Remove M/T console boot (M/T only).
10. Disengage console rear finisher metal clips and pawl.
11. Remove console rear finisher.
12. Disengage console mask cover metal clips and pawls, and then
remove console mask cover (with armrest).
PIIB6386E
PIIB2454J
PIIB2452J
PIIB6387E
Page 2123 of 2896
INSTRUMENT PANEL ASSEMBLY
IP-23
C
D
E
F
G
H
J
K
L
MA
B
IP
Revision: June 20062007 Versa
13. Disengage rear cup holder metal clips and pawls (without arm-
rest).
14. Remover rear cup holder (without armrest).
15. Remove console body assembly screws and nut.
16. Disconnect harness connector, and then remove console body assembly.
17. Remove both of the instrument lower cover LH and RH clips.
18. Disengage instrument lower cover LH and RH metal clips and
remove both of the instrument lower cover LH and RH.
19. Remove screws and then remove center console.
Installation
Installation is in the reverse order of removal.
PIIB6388E
PIIB2882J
Page 2124 of 2896
IP-24
INSTRUMENT PANEL ASSEMBLY
Revision: June 20062007 Versa
Disassembly and AssemblyEIS0097A
GLOVE BOX ASSEMBLY
Disassembly
1. Remove screws of damper, and then remove damper.
2. Remove screws of glove box striker, and then remove glove box striker.
3. Remove screws of glove box latch, and then remove glove box latch.
Assembly
Assembly is in the reverse order of disassembly.
1. Glove box striker 2. Glove box 3. Glove box latch
4. Damper
LIIA2555E
Page 2125 of 2896
INSTRUMENT PANEL ASSEMBLY
IP-25
C
D
E
F
G
H
J
K
L
MA
B
IP
Revision: June 20062007 Versa
CENTER CONSOLE ASSEMBLY
Disassembly
Remove the four screws, and then remove front cup holder from center console.
Assembly
Assembly is in the reverse order of disassembly.
COMBINATION METER
Disassembly
Disengage the eight tabs to separate front cover (1) from the unified
meter control unit assembly (2).
Assembly
Assembly is in the reverse order of disassembly.
1. Center console 2. Front cup holder
LIIA2556E
LIIA2582E
Page 2126 of 2896
IP-26
INSTRUMENT PANEL ASSEMBLY
Revision: June 20062007 Versa
Page 2127 of 2896

LAN-1
LAN SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION LAN
A
B
LAN
Revision: June 20062007 Versa
CAN FUNDAMENTAL
PRECAUTIONS .......................................................... 3
Precautions When Using CONSULT-II ..................... 3
Precautions for Trouble Diagnosis ........................... 3
Precautions for Harness Repair ............................... 3
SYSTEM DESCRIPTION ............................................ 4
CAN Communication System ................................... 4
SYSTEM DIAGRAM .............................................. 4
CAN COMMUNICATION CONTROL CIRCUIT ..... 5
Diag on CAN ............................................................ 6
DESCRIPTION ...................................................... 6
SYSTEM DIAGRAM .............................................. 6
TROUBLE DIAGNOSIS .............................................. 7
Condition of Error Detection ..................................... 7
CAN COMMUNICATION SYSTEM ERROR ......... 7
WHEN INDICATED “U1000” OR “U1001” IS INDI-
CATED EVEN THOUGH CAN COMMUNICA-
TION SYSTEM IS NORMAL ................................. 7
Symptom When Error Occurs in CAN Communi-
cation System ........................................................... 8
ERROR EXAMPLE ............................................... 8
Self-Diagnosis ........................................................ 12
CAN Diagnostic Support Monitor ........................... 13
MONITOR ITEM (CONSULT-II) .......................... 13
MONITOR ITEM (ON-BOARD DIAGNOSIS) ...... 14
TROUBLE DIAGNOSES WORK FLOW .................. 15
Information Needed for Trouble Diagnosis ............. 15
How to Use CAN Communication Signal Chart ..... 15
Trouble Diagnosis Flow Chart ................................ 16
Trouble Diagnosis Procedure ................................. 17
INTERVIEW WITH CUSTOMER ......................... 17
INSPECTION OF VEHICLE CONDITION ........... 18
CHECK OF CAN SYSTEM TYPE (HOW TO USE
CAN SYSTEM TYPE SPECIFICATION CHART) ... 19
CREATE INTERVIEW SHEET ............................ 21
CREATE DATA SHEET ....................................... 22
CREATE DIAGNOSIS SHEET ............................ 24
DETECT THE ROOT CAUSE ............................. 25
CAN
INDEX FOR DTC ....................................................... 40
DTC No. Index ........................................................ 40
HOW TO USE THIS SECTION ................................. 41
Caution ................................................................... 41
Abbreviation List ..................................................... 41
PRECAUTIONS ........................................................ 42
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................. 42
Precautions When Using CONSULT-II ................... 42
Precautions for Trouble Diagnosis ......................... 42
Precautions for Harness Repair ............................. 42
TROUBLE DIAGNOSIS ............................................ 44
CAN Diagnostic Support Monitor ............................ 44
MONITOR ITEM LIST (CONSULT-II) .................. 44
CAN System Specification Chart ............................ 47
VEHICLE EQUIPMENT IDENTIFICATION
INFORMATION .................................................... 47
CAN Communication Signal Chart ......................... 48
TYPE 1/TYPE 2/TYPE 3/TYPE 4 ........................ 48
TYPE 5/TYPE 6 ................................................... 49
TYPE 7/TYPE 8/TYPE 9/TYPE 10 ...................... 50
Schematic ............................................................... 53
Wiring Diagram — CAN — ..................................... 54
Interview Sheet ....................................................... 56
Data Sheet .............................................................. 57
CONSULT-II DATA ATTACHMENT SHEET ........ 57
CAN System (Type 1) ............................................. 60
DIAGNOSIS SHEET ........................................... 60
CAN System (Type 2) ............................................. 61
DIAGNOSIS SHEET ........................................... 61
CAN System (Type 3) ............................................. 62
DIAGNOSIS SHEET ........................................... 62
CAN System (Type 4) ............................................. 63
DIAGNOSIS SHEET ........................................... 63
CAN System (Type 5) ............................................. 64
DIAGNOSIS SHEET ........................................... 64
CAN System (Type 6) ............................................. 65
DIAGNOSIS SHEET ........................................... 65
Page 2128 of 2896

LAN-2Revision: June 20062007 Versa CAN System (Type 7) ............................................. 66
DIAGNOSIS SHEET ............................................ 66
CAN System (Type 8) ............................................. 67
DIAGNOSIS SHEET ............................................ 67
CAN System (Type 9) ............................................. 68
DIAGNOSIS SHEET ............................................ 68
CAN System (Type 10) ........................................... 69
DIAGNOSIS SHEET ............................................ 69
Component Parts Location ..................................... 70
Harness Layout ...................................................... 70
Malfunction Area Chart ........................................... 71
MAIN LINE ........................................................... 71
BRANCH LINE .................................................... 71
SHORT CIRCUIT ................................................ 71Main Line Between Data Link Connector and TCM ...72
Main Line Between Data Link Connector and ABS
Actuator and Electric Unit (Control Unit) .................73
ECM Branch Line Circuit .........................................74
BCM Branch Line Circuit .........................................74
Data Link Connector Branch Line Circuit ................75
EPS Control Unit Branch Line Circuit .....................76
Intelligent Key Unit Branch Line Circuit ...................76
Combination Meter Branch Line Circuit ..................77
ABS Actuator and Electric Unit (Control Unit) Branch
Line Circuit ..............................................................78
TCM Branch Line Circuit .........................................78
IPDM E/R Branch Line Circuit .................................79
CAN Communication Circuit ...................................80