Page 1465 of 2267
DIAGNOSTIC PROCEDURE 1-(1)
—With driver door switch type-2—
(Door switch check)
CHECK DOOR SWITCH INPUT SIG-
NAL.
Remove time control unit from fuse
block.
Note: Fuse block (J/B) is very frag-
ile. TCU should be removed care-
fully to avoid breaking the locking
bars.
Check continuity between fuse block
(J/B) and ground.
NG
OK
Door switch is OK.
CHECK DOOR SWITCH.
1) Disconnect door switch connector.
2) Check continuity between door
switch terminals.
OK
NG
Replace door switch.
Check the following.
Door switch ground condition
Harness for open or short between
control unit and door switch
Termi-
nalsCondition Continuity
Driver
side door
16JOpened Yes
Closed No
Other
door
7JOpened Yes
Closed No
Terminals Condition Continuity
1- groundClosed No
Open Yes
YEL829
Fuse block (J/B) connector
YEL033D
THEFT WARNING SYSTEM
Trouble Diagnoses (Cont’d)
EL-333
Page 1466 of 2267
DIAGNOSTIC PROCEDURE 1-(2)
(Hood switch check)
CHECK HOOD SWITCH INPUT SIG-
NAL.
Remove time control unit from fuse
block.
Note: Fuse block (J/B) is very frag-
ile. TCU should be removed care-
fully to avoid breaking the locking
bars.
Check continuity between control unit
terminal
32and ground.
Refer to wiring diagram in EL-317.
OK
OK
Hood switch is OK.
CHECK HOOD SWITCH.
1. Disconnect hood switch connector.
2. Check continuity between hood
switch terminals.
OK
NG
Replace hood switch.
Check the following.
Hood switch ground circuit
Harness for open or short between
control unit and hood switch
Condition Continuity
Hood is open. Yes
Hood is closed. No
Terminals Condition Continuity
1-2Pushed No
Released Yes
YEL457B Time control
unit connector
YEL458B Hood switch connector
THEFT WARNING SYSTEM
Trouble Diagnoses (Cont’d)
EL-334
Page 1467 of 2267

DIAGNOSTIC PROCEDURE 1-(3)
(Trunk room or luggage room lamp switch check)
CHECK TRUNK ROOM OR LUG-
GAGE ROOM LAMP SWITCH INPUT
SIGNAL.
Remove time control unit from fuse
block.
Note: Fuse block (J/B) is very frag-
ile. TCU should be removed care-
fully to avoid breaking the locking
bars.
Check continuity between control unit
terminal
33and ground.
Refer to wiring diagram in EL-319.
NG
OK
Trunk room or luggage
room lamp switch is OK.
CHECK TRUNK ROOM OR LUG-
GAGE ROOM LAMP SWITCH.
1. Disconnect trunk room or luggage
room lamp switch connector.
2. Check continuity between trunk
room lamp switch terminals.
OK
NG
Replace trunk room or
luggage room lamp
switch.
Check the following.
Trunk room or luggage room lamp
switch ground circuit
Harness for open or short between
control unit and trunk room or lug-
gage room lamp switch
Condition Continuity
Trunk lid or back
door is open.Ye s
Trunk lid or back
door is closed.No
Terminals Condition Continuity
1-2Closed No
Open Yes
YEL459B Time control
unit connector
YEL460B Trunk room lamp switch connector
Luggage room lamp switch
Luggage room lamp switch
THEFT WARNING SYSTEM
Trouble Diagnoses (Cont’d)
EL-335
Page 1468 of 2267

DIAGNOSTIC PROCEDURE 2
(Security indicator check)
CHECK INDICATOR LAMP OUTPUT
SIGNAL.
1) Remove time control unit from fuse
block.
Note: Fuse block (J/B) is very
fragile. TCU should be removed
carefully to avoid breaking the
locking bars.
2) Check voltage between control unit
terminal
18and ground.
Battery voltage should exist.
Refer to wiring diagram EL-316.
NG
OK
Security indicator lamp is
OK.
Security
indicator on
dashboardSecurity indica-
tor built-in com-
bination meterA
CHECK INDICATOR LAMP.
OK
NG
Replace indicator lamp.
CHECK POWER SUPPLY CIRCUIT
FOR INDICATOR.
1) Disconnect security indicator con-
nector.
2) Check voltage between indicator
terminal
2and ground.
Battery voltage should exist.
OK
NG
Check the following:
10A fuse [No.16 ,
located in the fuse
block (J/B)]
Harness for open or
short between security
indicator lamp and
fuse
Check harness for open or short
between security indicator and control
unit.
A
CHECK INDICATOR LAMP.
OK
NG
Replace combination
meter.
CHECK POWER SUPPLY CIRCUIT
FOR INDICATOR.
1) Disconnect combination meter con-
nector.
2) Check voltage between indicator
terminal
23and ground.
Battery voltage should exist.
OK
NG
Check the following:
10A fuse [No.16 ,
located in the fuse
block (J/B)]
Harness for open or
short between combi-
nation meter and fuse
Check harness for open or short
between combination meter and con-
trol unit.
YEL461B Time control
unit connector
YEL462B Security indicator
connector
YEL037D
THEFT WARNING SYSTEM
Trouble Diagnoses (Cont’d)
EL-336
Page 1469 of 2267

DIAGNOSTIC PROCEDURE 3
(Door unlock sensor check)
CHECK DOOR UNLOCK SENSOR INPUT
SIGNAL.
Remove time control unit from fuse block.
Note: Fuse block (J/B) is very fragile.
TCU should be removed carefully to
avoid breaking the locking bars.
Check continuity between control unit termi-
nals
25,35,36and ground.
Refer to wiring diagram in EL-327.
NG
OK
Door unlock sensor
is OK.
CHECK DOOR UNLOCK SENSOR.
1. Disconnect door unlock sensor connec-
tor.
2. Check continuity between door unlock
sensor terminals.
OK
NG
Replace door
unlock sensor.
Check the following:
Door unlock sensor ground circuit
Harness for open or short between con-
trol unit and door unlock sensor
Terminals
Condition Continuity
Driver
side door
35GroundLocked No
Unlocked Yes
Passen-
ger
side door
36GroundLocked No
Unlocked Yes
Rear
door
25GroundLocked No
Unlocked Yes
Terminals Condition Continuity
2-5Locked No
Unlocked Yes
YEL463B
Time control
unit connector
YEL038D
THEFT WARNING SYSTEM
Trouble Diagnoses (Cont’d)
EL-337
Page 1470 of 2267

DIAGNOSTIC PROCEDURE 4
(Door key cylinder switch check)
CHECK DOOR KEY CYLINDER
SWITCH INPUT SIGNAL (LOCK SIG-
NAL).
Remove time control unit from fuse
block.
Note: Fuse block (J/B) is very fragile.
TCU should be removed carefully to
avoid breaking the locking bars.
Check continuity between time control
unit connector terminal
29and
ground.
NG
OK
Door key cylinder switch
is OK.
CHECK DOOR KEY CYLINDER
SWITCH.
1) Disconnect door key cylinder switch
connector.
2) Check continuity between door key
cylinder switch terminals.
OK
NG
Replace key cylinder
switch.
Check the following:
Harness connectorsB3,M13
Harness connectorsM7,D1
Harness connectorsB5,D2
Harness connectorsB56,D11
Door key cylinder switch ground cir-
cuit
Harness for open or short-circuit
between super lock control unit and
door key cylinder.
Key cylinder switch operation Continuity
Between neutral and lock Yes
Unlock/neutral No
Terminals Key position Continuity
1-2
Neutral No
Between
neutral and
lockYe s
Unlock/
neutralNo
Full stroke
(Lock)No
YEL447B
Time control unit connector
Continuity exists
LockNeutral
Unlock
LH side
Neutral
UnlockContinuity exists
Lock
RH side
YEL817
Key cylinder switch
Driver side :
Passenger side:
THEFT WARNING SYSTEM
Trouble Diagnoses (Cont’d)
EL-338
Page 1471 of 2267
DIAGNOSTIC PROCEDURE 5
(Smash sensor check)
1. Remove time control unit from fuse
block.
Note: Fuse block (J/B) is very
fragile. TCU should be removed
carefully to avoid breaking the
locking bars.
2. Check harness continuity between
control unit terminal
31and ground.
Continuity should exist.
OK
NG
Check the following.
Smash sensor circuit
for open.
Harness for open
between control unit,
smash sensors and
ground.
1. Disconnect rear window smash sen-
sor connector.
2. Check harness continuity between
control unit and ground.
Continuity should not exist.
NG
OK
Smash sensor is OK.
Check harness for short between con-
trol unit and ground.
YEL457B Time control
unit connector
NEL546 Time control unit connector
THEFT WARNING SYSTEM
Trouble Diagnoses (Cont’d)
EL-339
Page 1472 of 2267

DIAGNOSTIC PROCEDURE 6
(Theft warning horn alarm check)
CHECK THEFT WARNING HORN
ALARM OPERATION.
1. Remove time control unit from fuse
block.
Note: Fuse block (J/B) is very
fragile. TCU should be removed
carefully to avoid breaking the
locking bars.
2. Apply ground to control unit connec-
tor terminal
43.
Does horn alarm activate?
Refer to wiring diagram EL-319.
No
Ye s
Horn alarm is OK.
Check theft warning horn relay.
OK
NG
Replace.
CHECK POWER SUPPLY FOR THEFT
WARNING HORN RELAY.
1) Disconnect theft warning horn relay
connector.
2) Check voltage between terminal
2
and ground, and3and ground.
Battery voltage should exist.
OK
NG
Check the following:
10A fuse (No.16 ,
located in the fuse and
fusible link box)
Harness for open or
short between theft
warning horn relay and
fuse
CHECK THEFT WARNING HORN
RELAY CIRCUIT.
1. Disconnect theft warning horn relay
connector.
2. Check continuity between theft
warning horn relay
1and control
unit terminal
43.
Continuity should exist.
3. Check continuity between theft
warning horn relay
5and theft
warning horn connector terminal
1.
Continuity should exist.
OK
NG
Repair harness.
Check harness for open or short
between theft warning horn relay and
control unit.
YEL465B
Time control unit connector
YEL466B
Theft warning horn
relay connector
YEL467B
Theft warning horn
relay connector
THEFT WARNING SYSTEM
Trouble Diagnoses (Cont’d)
EL-340