1999 NISSAN PRIMERA Electronic Repair Manual

mirror controls brake pads replacement jacking points technical data oil level jack points

Page 1201 of 2267

NISSAN PRIMERA 1999 Electronic Repair Manual Trouble Diagnoses
Symptom Possible cause Repair order
LH headlamps do not operate. 1. Bulb
2. Grounds
E11andE37
3. 15A fuse
4. Lighting switch1. Check bulb.
2. Check grounds
E11andE37
3. Check 15A fus

Trouble Diagnoses
Symptom Possible cause Repair order
LH headlamps do not operate. 1. Bulb
2. Grounds
E11andE37
3. 15A fuse
4. Lighting switch1. Check bulb.
2. Check grounds
E11andE37
3. Check 15A fuse [No.31 (gasoline engine),
32 (diesel engine) located in fuse and fusible link
box].
Verify battery positive voltage is present at termi-
nal
8of lighting switch.
4. Check lighting switch.
RH headlamps do not operate. 1. Bulb
2. Grounds
E11andE37
3. 15A fuse
4. Lighting switch1. Check bulb.
2. Check grounds
E11andE37
3. Check 15A fuse [No.32 (gasoline engine),
33 (diesel engine) located in fuse and fusible link
box].
Verify battery positive voltage is present at termi-
nal
5of lighting switch.
4. Check lighting switch.
LH high beams do not operate,
but LH low beam operates.1. Bulbs
2. Open in LH high beams circuit
3. Lighting switch1. Check bulbs.
2. Check R/B wire between lighting switch and LH
headlamps for an open circuit.
3. Check lighting switch.
LH low beam does not operate,
but LH high beam operates.1. Bulb
2. Open in LH low beam circuit
3. Lighting switch1. Check bulb.
2. Check R/Y wire between lighting switch and LH
headlamp for an open circuit.
3. Check lighting switch.
RH high beams do not operate,
but RH low beam operates.1. Bulbs
2. Open in RH high beams cir-
cuit
3. Lighting switch.1. Check bulbs.
2. Check R/G wire between lighting switch and RH
headlamps for an open circuit.
3. Check lighting switch.
RH low beam does not operate,
but RH high beam operates.1. Bulb
2. Open in RH low beam circuit
3. Lighting switch1. Check bulb.
2. Check P/L wire between lighting switch and RH
headlamp for an open circuit.
3. Check lighting switch.
High beam indicator does not
work.1. Bulb
2. Grounds
M6,M26andM28
orE11andE39
3. Open in high beam circuit1. Check bulb in combination meter.
2. Check grounds
M6,M26andM28orE11and
E39.
3. Check R/B wire between lighting switch and com-
bination meter for an open circuit.
HEADLAMP (without Daytime Light System)—Conventional Type—
EL-69

Page 1202 of 2267

NISSAN PRIMERA 1999 Electronic Repair Manual Bulb Replacement
The headlamp is a semi-sealed beam type which uses a replace-
able halogen bulb. The bulb can be replaced from the engine
compartment side without removing the headlamp body.
Grasp o

Page 1203 of 2267

NISSAN PRIMERA 1999 Electronic Repair Manual LOW BEAM
1. Turn headlamp low beam on.
2. Use adjusting screws to perform aiming adjustment.
First tighten the adjusting screw all the way and then
make adjustment by loosening the screw.
Adjust hea

Page 1204 of 2267

NISSAN PRIMERA 1999 Electronic Repair Manual System Description
Xenon type headlamp is adopted to the low beam headlamps. Xenon bulbs do not use a filament. Instead,
they produce light when a high voltage current is passed between two tungsten e

Page 1205 of 2267

NISSAN PRIMERA 1999 Electronic Repair Manual Wiring Diagram—H/LAMP—
YEL133C
BATTERY
Refer to EL-POWER.: With gasoline engine
: With diesel engine
OFF
1ST2ND
LOW
HIGHPASSOFF
1ST2ND
LOW
HIGHPASS
LOW
HIGHPASS
LOW
HIGHPASSCOMBINATION
SWITCH
(LIG

Page 1206 of 2267

NISSAN PRIMERA 1999 Electronic Repair Manual YEL004D
HEADLAMP (without Daytime Light System)—Xenon Type—
Wiring Diagram—H/LAMP—(Cont’d)
EL-74

Page 1207 of 2267

NISSAN PRIMERA 1999 Electronic Repair Manual WARNING:
The xenon headlamp has a high-tension current generating area. Be extremely careful when
removing and installing. Be certain to disconnect the battery negative cable prior to removing or
ins

WARNING:
The xenon headlamp has a high-tension current generating area. Be extremely careful when
removing and installing. Be certain to disconnect the battery negative cable prior to removing or
installing.
When the xenon headlamp is lit, do not touch the harness (covered with red or amber insulation),
bulb itself or the bulb socket with your bare hands.
Never service a xenon headlamp with wet hands.
When checking body side harness with a circuit tester, be certain to disconnect the harness
connector from the xenon headlamp.
When the xenon headlamp is lit, the xenon bulb must be installed in the headlamp housing.
(Never turn on xenon headlamp, if the bulb is out of the headlamp housing.)
CAUTION:
Make sure to install the bulb securely; if the xenon bulb is improperly installed in its socket, high-
tension current leaks occur. This may lead to a melted bulb and/or bulb socket.
Trouble Diagnoses
Symptom Possible cause Repair order
LH or RH xenon headlamp
(low beam) blinks, lacks
brightness or does not illu-
minate.1. 15A fuse 1. Check 20A fuse [No.
30(gasoline engine),
43(diesel engine) : LH, No.38(gasoline engine),
39(diesel engine), : RH, located in fuse and fusible
link box].
2. Relay 2. Check Headlamp relay.
3. Power supply circuit to headlamp
low beam3. Verify battery positive voltage is present at terminal
3of headlamp harness with lighting switch in
“2nd”and“Low”positions. (Before inspecting head-
lamp terminal, disconnect headlamp connector with
lighting switch in“OFF”position.)
4. Xenon bulb 4. Replace the xenon bulb with the other side bulb or
new one. (If headlamps illuminate correctly, replace
the bulb.)
5. HID control unit and booster 5. Replace the HID control unit and booster as a head-
lamp assembly.
LH or RH [both headlamp
high and xenon (low) beam]
do not illuminate.1. 15A fuse 1. Check 15A fuse [No.
30(Gasoline engine), No.43
(diesel engine), : LH, No.38(gasoline engine),
No.
39(diesel engine) located in fuse and fusible
link box].
2. Ground circuit 2. Check continuity between headlamp harness termi-
nal
2and body ground. (Before inspecting head-
lamp terminal, disconnect headlamp connector with
lighting switch in“OFF”position.)
LH or RH headlamp high
beam does not illuminate.1. Bulb
2. Power supply circuit to headlamp
high beam1. Check bulb.
2. Verify battery positive voltage is present at terminal
1of headlamp harness with lighting switch in
“2nd”and“HIGH”position. (Before inspecting head-
lamp terminal, disconnect headlamp connector with
lighting switch in“OFF”position.)
HID: High Intensity Discharge
HEADLAMP (without Daytime Light System)—Xenon Type—
EL-75

Page 1208 of 2267

NISSAN PRIMERA 1999 Electronic Repair Manual Bulb Replacement
CAUTION:
After replacing a new xenon bulb, be sure to make aim-
ing adjustments.
Hold only the plastic base when handling the bulb. Never
touch the glass envelope.
Do not leave hea

Load next 8 pages

Page: < prev 1-10 ... 1169-1176 1177-1184 1185-1192 1193-1200 1201-1208 1209-1216 1217-1224 1225-1232 1233-1240 ... 2272 next >

oil level tire pressure reset tire type headlamp dimensions parking sensors