Page 217 of 2267
Clip and Fastener
lClips and fasteners in BT section correspond to the following numbers and symbols.
lReplace any clips and/or fasteners which are damaged during removal or installation.
Symbol
No.Shapes Removal & Installation
C101
SBF302HSBF367BA
C103
SBT095SBF423H
C203
SBF258GSBF708E
C205
MBT080ASBF638C Removal:
Remove by bending up with
flat-bladed screwdrivers or
clip remover.
Removal:
Remove with a clip remover.
Push center pin to
catching position.
(Do not remove
center pin by hitting it.) Push
Installation:Push
Removal:
Screwdriver
Clip
Finisher
GENERAL SERVICING
BT-3
Page 218 of 2267
Symbol
No.Shapes Removal & Installation
CE117
SBF174DSBF175DA
CF118
SBF151DSBF259G
CR103
SBF768B
SBF770B
CS101
SBF078BSBF992G Removal:
Remove by bending up with a
flat-bladed screwdriver or pliers.
Clip-A
Clip-B
(Grommet)
Sealing
washer
Removal:
Holder portion of clip must be spread
out to remove rod
Removal:
1. Screw out with a Phillips screwdriver.
2. Remove female portion with flat-bladed
screw-driver. Removal:
Flat-bladed screwdriver
Finisher
Clip-B
(Grommet)
Clip-A
Sealing
washers Body
panel
GENERAL SERVICING
Clip and Fastener (Cont'd)
BT-4
Page 219 of 2267

Body Front End
lWhen removing or installing hood, place a cloth or other padding on the front fender panels and cowl
top. This prevents vehicle body from being scratched.
lBumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
lHood adjustment: Adjust at hinge portion.
lHood lock adjustment: After adjusting, check hood lock control operation. Apply a coat of grease to hood
locks engaging mechanism.
lHood opener: Do not attempt to bend cable forcibly. Doing so increases effort required to unlock hood.
REMOVAL Ð Front bumper assembly
p1Remove clipsC205securing bumper fascia to engine undercover.
p2Remove screws and clipsC205securing left and right sides of front fender protector.
p3Remove screws securing radiator core support to bumper fascia.
p4Remove screws securing left and right front fenders to bumper fascia.
p5Remove clipsCS101securing retainer to bumper fascia.
p6Extract bumper fascia assembly.
p7Remove screws securing fog lamps. Then remove fog lamps.
YBT001
10.8 - 14.6 N´m
(1.1 - 1.5 kg-m,
8.0 - 10.8 ft-lb)
BODY END
BT-5
Page 220 of 2267
NBT033
SEC. 261×620×623×650×656
Hood lock adjustmentlAdjust hood so that hood primary lock
meshes at a position 1 to 1.5 mm (0.039 to
0.059 in) lower than fender.
lAfter hood lock adjustment, adjust bumper
rubber.
lWhen securing hood lock, ensure it does not
tilt. Striker must be positioned at the center of
hood primary lock.
lAfter adjustment, ensure that hood primary and sec-
ondary lock operate properly.
More than 5.0 mm (0.197 in)
Hood
Secondary latch
Bumper rubber adjustment
lAdjust so that hood is aligned
with fender. At that time deflection
is approx. 2 mm (0.08 in).
[Bumper rubber free height is
approx. 13 mm (0.51 in).]Hood adjustment
20.6 - 26.5
(2.1 - 2.7,
15 - 20)
Bumper fascia assembly
H: Bumper assembly mounting bolts, screw & clips
: N´m (kg-m, ft-lb)Fog lamp
CS101
HH
C205
C205
H
H
H
.Hood lock secondary latch hooking length
BODY END
Body Front End (Cont'd)
BT-6
Page 221 of 2267

Body Rear End and Opener
4-DOOR SEDAN
lWhen removing or installing trunk lid, place a cloth or other padding on rear fender panels. This pre-
vents vehicle body from being scratched.
lBumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
lTrunk lid adjustment: Adjust at hinge-trunk lid portion for proper trunk lid fit.
lTrunk lid lock system adjustment: Adjust striker so that it is in the center of the lock. After adjustment,
check trunk lid lock operation.
WARNING:
lBe careful not to scratch trunk lid stay when installing trunk lid.
A scratched stay may cause gas leakage.
lThe contents of the trunk lid stay are under pressure. Do not take apart puncture, apply heat or
allow fire near it.
lOpener cable: Do not attempt to bend cable using excessive force.
lAfter installation, make sure that trunk lid and fuel filler lid open smoothly.
NBT034
5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
Upper
Spring holder
LowerOpener handle
Opener cable
Lock nut
Fuel filler lid opener & control
Trunk lid striker
.5.1 - 6.37
(0.52 - 0.65,
45.1 - 56.4)
: N´m (kg-m, ft-lb)
20.6 - 26.5
(2.1 - 2.7,
15 - 20)
: N´m (kg-m, in-lb) Cloth
Actuator
.Trunk lid lock
key cylinder
.Trunk lid lock
.5.1 - 6.37
(0.52 - 0.65, 45.1 - 56.4)
BODY END
BT-7
Page 222 of 2267
REMOVAL Ð Rear bumper assembly
p1Remove license plate lamp.
p2Remove clipsC203securing left and right chipping protector.
p3Remove screws securing bumper fascia to left and right rear fenders.
p4Remove clipsCS101securing bumper fascia to real panel.
p5Remove clipsC205securing bumper fascia to rear panel upper.
p6Extract bumper fascia assembly.
YBT062
BODY END
Body Rear End and Opener (Cont'd)
BT-8
Page 223 of 2267

5-DOOR HATCHBACK
lBack door adjustment: Adjust at hinge-body portion for proper back door fit.
lBack door lock system adjustment: Adjust lock & striker so that they are in the center. After adjustment,
check back door lock operation.
WARNING:
lBe careful not to scratch back door stay when installing back door. A scratched stay may cause
gas leakage.
lThe contents of the back door stay are under pressure. Do not take apart, puncture, apply heat
or allow fire near it.
lOpener cable: Do not attempt to bend cable using excessive force.
lAfter installation, make sure that back door and fuel filler lid open smoothly.
REMOVAL Ð Rear bumper assembly
p1Remove license plate lamp
p2Remove clipsC203securing left and right chipping protector.
p3Remove screws securing bumper fascia to left and right rear fenders.
p4Remove clipsCS101securing bumper fascia to rear panel.
p5Remove clipsC205securing bumper fascia to rear panel upper.
p6Extract bumper fascia assembly.
NBT036 Opener handleOpener cable
Lock nut
Fuel filler lid opener & control
20.6 - 26.5
(2.10 - 2.70,
15.2 - 19.5)
12.7 - 15.7
(1.30 - 1.60,
9.4 - 11.6)12.7 - 15.7
(1.30 - 1.60,
9.4 - 11.6)
12.7 - 15.7
(1.30 - 1.60,
9.4 - 11.6)
20.6 - 26.5
(2.10 - 2.70,
15.2 - 19.5)
: N´m (kg-m, ft-lb) Cloth
.5.1 - 6.37
(0.52 - 0.65, 45.1 - 56.4)
Actuator
Key
cylinder
BODY END
Body Rear End and Opener (Cont'd)
BT-9
Page 224 of 2267
YBT061
BODY END
Body Rear End and Opener (Cont'd)
BT-10