Page 513 of 3061
VARIABLE BLOWER CONTROLATC-143
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
VARIABLE BLOWER CONTROL
Removal and InstallationINFOID:0000000003533287
Variable Blower Control - Front Heater and Cooling Unit Assembly
REMOVAL
1. Remove the glove box assembly. Refer to IP-10, "Removal and Installation".
2. Disconnect the variable blower control electrical connector.
3. Remove the two screws and remove the variable blower control.
INSTALLATION
Installation is in the reverse order of removal.
LJIA0139E
1. Front heater and cooling unit assembly 2. Intake door motor 3. Air mix door motor (driver)
4. Variable blower control 5. Air mix door motor (passenger) 6. Mode door motor
7. Defroster door motor
Page 514 of 3061
ATC-144
< SERVICE INFORMATION >
REAR BLOWER MOTOR RESISTOR
REAR BLOWER MOTOR RESISTOR
Removal and InstallationINFOID:0000000003533288
Rear Blower Motor Resistor
REMOVAL
1. Remove the luggage side finisher lower RH. Refer to EI-39.
2. Disconnect the rear blower motor resistor electrical connector.
3. Remove the two screws and remove the rear blower motor resistor.
INSTALLATION
Installation is in the reverse order of removal.
LJIA0055E
1. Rear blower motor 2. Rear blower motor case 3. Rear blower motor resistor
Page 515 of 3061
DUCTS AND GRILLESATC-145
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
DUCTS AND GRILLES
ComponentINFOID:0000000003533289
Ducts - Front Heater and Cooling Unit Assembly
WJIA0956E
1. Defroster nozzle 2. LH side demister duct 3. LH ventilator duct
4. RH side demister duct 5. RH ventilator duct 6. Center ventilator duct
Page 516 of 3061
ATC-146
< SERVICE INFORMATION >
DUCTS AND GRILLES
Ducts - Rear Heater and Cooling Unit Assembly
7. Front heater and cooling unit assembly 8. Floor duct 9. Clips
10. Heat duct
LJIA0142E
1. Rear floor duct 2. Rear heater and cooling unit assembly 3. Rear lower overhead duct
4. Rear upper overhead duct
Page 517 of 3061
DUCTS AND GRILLESATC-147
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
Grilles
LJIA0140E
1. Overhead console trim panel 2. Overhead console front grilles (front) 3. Overhead console rear grilles (rear)
4. Instrument panel 5. Storage tray bottom cover (LH) 6. LH side ventilator and demister grille
7. LH ventilator grille 8. RH ventilator grille 9. RH side ventilator and demister grille
10. Storage tray bottom cover (RH)
Page 518 of 3061

ATC-148
< SERVICE INFORMATION >
DUCTS AND GRILLES
Removal and Installation
INFOID:0000000003533290
CENTER CONSOLE HEAT DUCT AND REAR FINISHER ASSEMBLY GRILLE
Removal
The center console must be removed and disassembled to remove the heat duct and rear finisher assembly
grille. Refer to IP-10, "
Removal and Installation".
Installation
Installation is in the reverse order of removal.
DEFROSTER NOZZLE
Removal
1. Remove the instrument panel trim. Refer to IP-10, "Removal and Installation".
2. Remove the front heater and cooling unit assembly. Refer to ATC-133, "
Removal and Installation".
3. Remove the defroster nozzle.
Installation
Installation is in the reverse order of removal.
RH AND LH SIDE DEMISTER DUCT
Removal
1. Remove the instrument panel trim. Refer to IP-10, "Removal and Installation".
2. Remove the front heater and cooling unit assembly. Refer to ATC-133, "
Removal and Installation".
3. Remove the RH or LH side demister duct.
Installation
Installation is in the reverse order of removal.
RH AND LH VENTILATOR DUCT
Removal
1. Remove the instrument panel trim. Refer to IP-10, "Removal and Installation".
2. Remove the front heater and cooling unit assembly. Refer to ATC-133, "
Removal and Installation".
3. Remove the RH or LH ventilator duct.
Installation
Installation is in the reverse order of removal.
CENTER VENTILATOR DUCT
Removal
1. Remove the instrument panel trim. Refer to IP-10, "Removal and Installation".
2. Remove the front heater and cooling unit assembly. Refer to .
3. Remove the defroster nozzle.
4. Remove the RH and LH side demister ducts.
5. Remove the RH and LH ventilator ducts.
6. Remove the center ventilator duct.
Installation
Installation is in the reverse order of removal.
FLOOR DUCT
Removal
1. Remove the floor carpet. Refer to EI-36.
2. Remove the two clips and remove the floor duct.
Installation
Installation is in the reverse order of removal.
Page 519 of 3061

DUCTS AND GRILLESATC-149
< SERVICE INFORMATION >
C
DE
F
G H
I
K L
M A
B
AT C
N
O P
REAR OVERHEAD DUCTS
Removal
1. Remove the luggage side finisher lower RH. Refer to EI-39.
2. Remove the headliner. Refer to EI-37
.
NOTE:
The rear headliner duct connected to the rear over head duct is part of the headlining trim panel and is
replaced as an assembly.
3. Remove the two bolts and remove the rear upper and lower overhead ducts.
Installation
Installation is in the reverse order of removal.
REAR FLOOR DUCT
Removal
1. Remove the luggage side finisher lower RH. Refer to EI-39.
2. Reposition the floor carpet out of the way.
3. Remove the two bolts and remove the rear floor duct.
Installation
Installation is in the reverse order of removal.
GRILLES
Removal
1. Remove the interior trim panels as necessary. Refer to IP-10, "Removal and Installation" or EI-37.
2. Remove the grille from the interior trim panel. NOTE:
To remove the overhead console front and rear grilles, turn the grille counter-clockwise to release the
grille from the overhead console trim panel.
Installation
Installation is in the reverse order of removal.
Page 520 of 3061

ATC-150
< SERVICE INFORMATION >
REFRIGERANT LINES
REFRIGERANT LINES
HFC-134a (R-134a) Service ProcedureINFOID:0000000003533291
SETTING OF SERVICE TOOLS AND EQUIPMENT
Discharging Refrigerant
WARNING:
Avoid breathing A/C refrigerant and oil vapor or mist. Exposure may irritate eyes, nose and throat.
Remove HFC-134a (R-134a) refrigerant from the A/C system using certified service equipment meeting
requirements of SAE J2210 HFC-134a (R-134a) r ecycling equipment or SAE J2201 HFC-134a (R-134a)
recovery equipment. If an accident al system discharge occurs, ventila te the work area before resum-
ing service. Additional h ealth and safety information may be obtain ed from the refrigerant and oil man-
ufacturers.
Evacuating System and Charging Refrigerant
1. Shut-off valve 2. A/C service valve 3. Recovery/recycling equipment
WJIA0579E
1. Shut-off valve 2. A/C service valve 3. Recovery/recycling equipment
4. Refrigerant container (HFC-134a) 5. Weight scale (J-39650) 6. Evacuating vacuum pump (J-39699)
7. Manifold gauge set (J-39183)
WJIA0580E