Page 281 of 3061
ON-VEHICLE SERVICE
AT-211
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
CONTROL VALVE WITH TCM REMOVAL AND INSTALLATION
Removal
1. Disconnect negative battery terminal
2. Drain ATF through drain plug.
3. Disconnect A/T assembly harness connector.
1. Transmission 2. Snap ring 3. Sub-harness
4. Control valve with TCM 5. Bracket 6. A/T fluid temperature sensor 2
7. Oil pan gasket 8. Brackets 9. Oil pan bolt
10. Oil pan 11. Magnet 12. Drain plug
13. Drain plug gasket 14. Terminal cord assembly 15. O-ring
AWDIA0024ZZ
Page 282 of 3061
AT-212
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
4. Remove snap ring from A/T assembly harness connector.
5. Push A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
6. Remove oil pan and oil pan gasket. Refer to AT-209, "
Oil Pan".
7. Disconnect A/T fluid temperature sensor 2 connector (A).
CAUTION:
Be careful not to damage connector.
8. Straighten the four terminal clips to free the terminal cord
assembly for A/T fluid temperature sensor 2 harness.
• : Terminal clip
9. Straighten terminal clip to free the revolution sensor harness.
10. Disconnect revolution sensor connector.
CAUTION:
Be careful not to damage connector.
SCIA5021E
SCIA5022E
SCIA8124E
SCIA7525E
Page 283 of 3061
ON-VEHICLE SERVICE
AT-213
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
11. Remove bolts (A), (B) and (C) from control valve with TCM.
• : Front
12. Remove control valve with TCM from transmission case.
CAUTION:
Be careful with the manual valve notch and manual plate
height. Remove it vertically.
13. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
14. Remove bracket from A/T fluid temperature sensor 2.
15. Remove O-ring from A/T assembly harness connector.
Bolt symbol Length mm (in) Number of bolts
A 42 (1.65) 5
B 55 (2.17) 6
C 40 (1.57) 1
SCIA8074E
SCIA5142E
SCIA5253E
SCIA5264E
SCIA5155E
Page 284 of 3061
AT-214
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
16. Disconnect TCM connectors.
CAUTION:
Be careful not to damage connectors.
17. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
18. Disconnect TCM connector and park/neutral position switch
connector
CAUTION:
Be careful not to damage connectors.
Installation
1. Connect TCM connector and park/neutral position switch con-
nector.
SCIA5447E
SCIA5448E
SCIA5449E
SCIA5449E
Page 285 of 3061
ON-VEHICLE SERVICE
AT-215
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
2. Install A/T assembly harness connector to control valve with
TCM.
3. Connect TCM connector.
4. Install new O-ring in A/T assembly harness connector.
NOTE:
• Do not reuse O-ring.
• Apply ATF to O-ring.
5. Install A/T fluid temperature sensor 2 to bracket.
6. Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolts to
the specified torque. Refer to AT-228, "
Component".
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
SCIA5450E
SCIA5447E
SCIA5155E
SCIA5264E
SCIA5253E
Page 286 of 3061
AT-216
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
7. Install control valve with TCM in transmission case.
CAUTION:
• Make sure that turbine revolution sensor securely installs
turbine revolution sensor hole.
• Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that manual valve cutout is engaged with
manual plate projection.
8. Install bolts (A), (B) and (C) in control valve with TCM.
• : Front
9. Tighten bolt (1), (2) and (3) temporarily to prevent dislocation. Then tighten them in order (1 → 2 → 3),
and then tighten other bolts.
• : Front
10. Tighten control valve with TCM bolts to the specified torque.
Refer to AT-228, "
Component".
SCIA5034E
SCIA5142E
Bolt symbol Length mm (in) Number of bolts
A 42 (1.65) 5
B 55 (2.17) 6
C 40 (1.57) 1
SCIA8074E
SCIA8075E
Page 287 of 3061
ON-VEHICLE SERVICE
AT-217
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
MA
B
AT
N
O
P
11. Connect A/T fluid temperature sensor 2 connector (A).
12. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
• : Terminal clip
13. Connect revolution sensor connector.
14. Securely fasten revolution sensor harness with terminal clip.
15. Install oil pan to transmission case. Refer to AT-209, "
Oil Pan".
16. Pull up A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
SCIA8124E
SCIA7524E
SCIA7525E
SCIA5038E
Page 288 of 3061

AT-218
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
17. Install snap ring to A/T assembly harness connector.
18. Connect A/T assembly harness connector.
19. Connect the negative battery terminal
20. Refill the A/T with fluid and check fluid level and for fluid leak-
age. Refer to AT-13, "
Changing Automatic Transmission Fluid
(ATF)".
CAUTION:
After completing installation, check A/T fluid leakage and fluid
level. Refer to AT-13, "
Changing Automatic Transmission Fluid
(ATF)", AT-13, "Checking Automatic Transmission Fluid (ATF)".
A/T FLUID TEMPERATURE SENSOR 2 REMOVAL AND INSTALLATION
Removal
1. Disconnect negative battery terminal
2. Remove oil pan and oil pan gasket. Refer to AT-209, "
Oil Pan".
3. Disconnect A/T fluid temperature sensor 2 connector (A).
CAUTION:
Be careful not to damage connector.
4. Straighten terminal clip to free A/T fluid temperature sensor 2
harness.
• : Terminal clip
5. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
6. Remove bracket from A/T fluid temperature sensor 2.
Installation
SCIA5039E
SCIA8125E
SCIA5253E
SCIA5264E