2004 DAEWOO NUBIRA Service Repair Manual

airbag off fuel sat nav reset infotainment system ground clearance oil temperature

Page 561 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual ENGINE CONTROLS 1F – 315
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
131. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temper

Page 562 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual 1F – 316IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1511
IDLE CHARGE ACTUATOR CIRCUIT FAULT
Circuit Description
The aim of the MTIA (Main Throttle Idle Actuator) is to con-
tr

1F – 316IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1511
IDLE CHARGE ACTUATOR CIRCUIT FAULT
Circuit Description
The aim of the MTIA (Main Throttle Idle Actuator) is to con-
trol the idle speed with the throttle body itself. The throttle
is motorized for low opening angle (0°, 19°). The charac-
teristics of the air flow are not the same for low and high
opening angles. As a matter of fact, the gradient of the
mass air flow function of TPS is lower for small angles that
permits to be more precise during the idle speed control.
Out of idle speed the throttle is actuated mechanically by
a classical accelcable.
The DC–motor commands the actuator for idle
Conditions for Setting the DTC
S The engine is running.
S The throttle position is set between 0.25 and 5.65.
S DTCs P0222 and P0223 are not set.
S The reference range of MTIA higher than 59.5% or
less than –70% for longer than 5 seconds.
(1.4L DOHC)
S The reference range of MTIA higher than 35% or
less than –35% at least 5 seconds. (1.6L DOHC)
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive trip with a fail.S The ECM will record operating conditions at the
time the diagnostic fail. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
An Intermittent problem may be caused by a poor connec-
tion, rubbed through wire insulation, or wire that is broken
inside the insulation.
Any circuitry, that is suspected as causing the complaint,
should be thoroughly checked for the following conditions.
S Backed–out terminals
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal to wire connection
S Physical damage to the wiring harness

Page 563 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual ENGINE CONTROLS 1F – 317
DAEWOO V–121 BL4
DTC P1511 – Idle Charge Actuator Circuit Fault
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check compl

ENGINE CONTROLS 1F – 317
DAEWOO V–121 BL4
DTC P1511 – Idle Charge Actuator Circuit Fault
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Turn the Turn the ignition switch to ON.
Is the Malfunction Indicator Lamp(MIL) on steady?–Go to Step 4Go to Step 3
31. Connect the scan tool the DLC.
2. Turn the Turn the ignition switch to ON.
Does the scan tool display serial data?–Go to Step 4Try with
another scan
tool
4Start the engine.
Does the engine start?–Go to Step 5Go to
”Engine Cranks
But Will Not
Run”
51. Turn the ignition switch to LOCK.
2. Connect the scan tool to the DLC.
3. Turn the Turn the ignition switch to ON.
Are any Diagnostic Trouble Codes (DTCs) dis-
played?–Go to Step 6Try with
another scan
tool
6Refer to the applicable DTC table.
Is only one DTC identified as valid trouble code
P1511?–Go to Step 7Go to Applica-
ble DTC Table
and Go to
”Multiple DTC”
71. Turn the ignition switch to LOCK.
2. Disconnect the MTIA connector.
3. Disconnect the ECM connector.
4. Measure resistance between MTIA connector
terminal 4 and ECM connector terminal 43.
Does the resistance measure with the value speci-
fied?0WGo to Step 8Go to Step 9
8Measure resistance between MTIA connector termi-
nal 8 and ECM connector terminal 19.
Does the resistance measure within the value speci-
fied?0WGo to Step 10Go to Step 11
91. Repair the wire or the connector terminal as
needed.
S Clear any DTCs from ECM.
S Perform the diagnostic system check.
Is the repair complete?–System OKGo to Step 8
101. Repair the wire or the connector terminal as
needed.
S Clear any DTCs from ECM.
S Perform the diagnostic system check.
Is the repair complete?–System OKGo to Step 11
111. Turn the ignition switch to LOCK.
2. Replace the throttle body assembly.
S Clear any DTCs from ECM.
S Perform the diagnostic system check.
Is the repair complete?–System OKGo to Step 12

Page 564 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual 1F – 318IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
121. Turn the ignition switch to LOCK.
2. Replace the ECM.
3. Perform the diagnostic system check.
Is the repair complete?�

Page 565 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual ENGINE CONTROLS 1F – 319
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1512
IDLE CHARGE ACTUATOR MECHANICAL ERROR
Circuit Description
The aim of the MTIA (Main Throttle Idle Actuator) is to con

ENGINE CONTROLS 1F – 319
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1512
IDLE CHARGE ACTUATOR MECHANICAL ERROR
Circuit Description
The aim of the MTIA (Main Throttle Idle Actuator) is to con-
trol the idle speed with the throttle body itself. The throttle
is motorized for low opening angle (0°, 19°). The charac-
teristics of the air flow are not the same for low and high
opening angles. As a matter of fact, the gradient of the
mass air flow function of TPS is lower for small angles that
permits to be more precise during the idle speed control.
Out of idle speed the throttle is actuated mechanically by
a classical accelcable.
The DC–motor commands the actuator for idle
Conditions for Setting the DTC
S The engine is running.
S The MTIA set point is between 0.25 and 5.65.
S DTCs P0222 and P0223 are not set.
S The reference range of MTIA higher than 59.5% or
less than –70% for longer than 10 seconds.
(1.4L DOHC)
S The reference range of MTIA higher than 35% or
less than –35% at least 10seconds. (1.6L DOHC)
S Mechanical problems exists.
– problem of accel cable hose
– problem inside MTIA : seizing by friction,
snooted, fouling.
Action Taken When the DTC SetsS The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive trip with a fail.
S The ECM will record operating conditions at the
time the diagnostic fail. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
An Intermittent problem may be caused by a poor connec-
tion, rubbed through wire insulation, or wire that is broken
inside the insulation.
Any circuitry, that is suspected as causing the complaint,
should be thoroughly checked for the following conditions.
S Backed–out terminals
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal to wire connection
S Physical damage to the wiring harness

Page 566 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual 1F – 320IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1512 – Idle Charge Actuator Mechanical Error
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check com

Page 567 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual ENGINE CONTROLS 1F – 321
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1513
IDLE CHARGE ACTUATOR FUNCTIONAL ERROR
Circuit Description
The aim of the MTIA (Main Throttle Idle Actuator) is to con

Page 568 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual 1F – 322IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1513 – Idle Charge Actuator Functional Error
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check com

1F – 322IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P1513 – Idle Charge Actuator Functional Error
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Turn the Turn the ignition switch to ON.
Is the Malfunction Indicator Lamp(MIL) on steady?–Go to Step 4Go to Step 3
31. Connect the scan tool the DLC.
2. Turn the Turn the ignition switch to ON.
Does the scan tool display serial data?–Go to Step 4Try with
another scan
tool
4Start the engine.
Does the engine start?–Go to Step 5Go to
”Engine Cranks
But Will Not
Run”
51. Turn the ignition switch to LOCK.
2. Connect the scan tool to the DLC.
Turn the Turn the ignition switch to ON.
Are any Diagnostic Trouble Codes (DTCs) dis-
played?–Go to Step 6Try with
another scan
tool
6Refer to the applicable DTC table.
Is only one DTC identified as valid trouble code
P1513?–Go to Step 7Go to Applica-
ble DTC Table
and Go to
”Multiple DTC”
71. Turn the ignition switch to LOCK.
2. Disconnect the MTIA connector.
3. Disconnect the ECM connector.
4. Measure resistance between MTIA connector
terminal 4 and ECM connector terminal 43.
Does the resistance measure with the value speci-
fied?0WGo to Step 8Go to Step 9
8Measure resistance between MTIA connector termi-
nal 8 and ECM connector terminal 19.
Does the resistance measure within the value speci-
fied?0WGo to Step 10Go to Step 11
91. Repair the wire or the connector terminal as
needed.
2. Clear any DTCs from ECM.
3. Perform the diagnostic system check.
Is the repair complete?–System OKGo to Step 8
101. Repair the wire or the connector terminal as
needed.
2. Clear any DTCs from ECM.
3. Perform the diagnostic system check.
Is the repair complete?–System OKGo to Step 11
111. Turn the ignition switch to LOCK.
2. Replace the throttle body assembly.
S Clear any DTCs from ECM.
S Perform the diagnostic system check.
Is the repair complete?–System OKGo to Step 12

Load next 8 pages

Page: < prev 1-10 ... 529-536 537-544 545-552 553-560 561-568 569-576 577-584 585-592 593-600 ... 2648 next >

lane assist open hood child restraint handbrake clutch key battery