2004 DAEWOO NUBIRA Service Repair Manual

child lock fuel consumption gas type differential ignition fuse

Page 785 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual ENGINE CONTROLS 1F – 539
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1133
FRONT HEATED OXYGEN SENSOR (HO2S1) TOO FEW
TRANSITION
Circuit Description
The Engine Control Module (ECM) continuousl

ENGINE CONTROLS 1F – 539
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1133
FRONT HEATED OXYGEN SENSOR (HO2S1) TOO FEW
TRANSITION
Circuit Description
The Engine Control Module (ECM) continuously monitors
the Front Heated Oxygen Sensor (HO2S1) activity for 100
seconds. During the monitor period, the ECM counts the
number of times that the HO2S1 switches from rich to lean
and from lean to rich. With this information, a total for all
switches can be determined. If the number of switches is
too low, a Diagnostic Trouble code (DTC) P1133 will set.
The lean–to–rich and rich–to–lean are less than 15
switches.
Conditions for Setting the DTC
S HO2S1 signal switches from 0.3 to 0.6 volts and
0.6 to 0.3 volts is less than 15 times within 90sec-
onds.
S Closed loop stoichiometry.
S Engine Coolant Temperature (ECT) is greater than
70 °C (158 °F).
S System voltage is greater than 10 volts.
S Engine run time is greater than 60 seconds.
S Purge Duty Cycle (DC) is less than 20%.
S The rpm is between 1600 and 4300.
S Airflow is between 9 and 40 g/sec.S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0131, P0132, P0134, P0135,
P1167, P0171, P1171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P0405, P0406, P0506,
P0507, P1404, and P0443 are not set.
S 2 second delay after conditions are met.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.

Page 786 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual 1F – 540IENGINE CONTROLS
DAEWOO V–121 BL4
Diagnostic Aids
DTC P1133 is most likely caused by one of the following
items:
S Fuel Pressure – The system will go rich if the fuel
pressure is too hi

1F – 540IENGINE CONTROLS
DAEWOO V–121 BL4
Diagnostic Aids
DTC P1133 is most likely caused by one of the following
items:
S Fuel Pressure – The system will go rich if the fuel
pressure is too high. The ECM can compensate for
some increase. However, if it gets too high, a DTC
P1133 may set. Refer to ”Fuel System Diagnosis”
in this section.
S Leaking injector – A leaking or malfunctioning injec-
tor can cause the system to go rich.
S Manifold Absolute Pressure (MAP) sensor – An
output that causes the ECM to sense a higher than
normal manifold pressure (low vacuum) can cause
the system to go rich. Disconnecting the MAP sen-
sor will allow the ECM to set a fixed value for the
MAP sensor. Substitute a different MAP sensor if
the rich condition is gone while the sensor is dis-
connected.
S Pressure regulator – Check for a leaking fuel pres-
sure regulator diaphragm by checking for the pres-
ence of liquid fuel in the vacuum line to the pres-
sure regulator.
S Throttle Position (TP) sensor – An intermittent TP
sensor output can cause the system to go rich due
to a false indication of the engine accelerating.S HO2S1 contamination – Inspect the HO2S1 for sili-
cone contamination from fuel or improper use of
Room Temperature Vulcanizing (RTV) sealant. The
sensor may have a white powdery coating and re-
sult in a high but false voltage signal (rich exhaust
indication). The ECM will then reduce the amount
of fuel delivered to the engine causing a severe
surge or driveability problem.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Chart.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
14. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
16. If no malfunctions have been found at this point and
no additional DTCs are set, refer to ”Diagnostic
Aids” in this section for additional checks and infor-
mation.
DTC P1133 – Front Heated Oxygen Sensor (HO2S1) Too Few
Transition
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Are any additional Diagnostic Trouble Codes
(DTCs) set?–Go to
applicable DTC
tableGo to Step 3
31. Start the engine and idle at normal operating
temperature.
2. Operate the vehicle within the specified param-
eter under the Conditions For Setting the DTC.
3. Monitor the lean–to–rich transition and rich–to–
lean transition and note the number of
switches.
Does the parameter show fewer transitions than the
specified value within 90 seconds.15Go to Step 4Go to Step 18

Page 787 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual ENGINE CONTROLS 1F – 541
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
4Visually/physically inspect for the following items:
S Front Heated Oxygen Sensor (HO2S1) is se-
curely installed.
S Corros

Page 788 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual 1F – 542IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
131. Turn the ignition OFF.
2. Check the continuity between terminal 4 of
HO2S1 and the terminal M12 of the ECM.
3. If the c

Page 789 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual ENGINE CONTROLS 1F – 543
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1134
FRONT HEATED OXYGEN SENSOR (HO2S1)
TRANSITION RATIO
Circuit Description
The Engine Control Module (ECM) monitors the

ENGINE CONTROLS 1F – 543
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1134
FRONT HEATED OXYGEN SENSOR (HO2S1)
TRANSITION RATIO
Circuit Description
The Engine Control Module (ECM) monitors the Front
Heated Oxygen Sensor (HO2S1) activity for 100 seconds
after closed loop and stoichiometric operation have been
established. During the monitoring period the ECM counts
the number of times that the HO2S1 responds from rich
to lean and adds the amount of time it took to complete all
transitions. With this information, an average time for all
transitions can be determined. The ECM then divides the
–to–lean average by the lean–to–rich average to obtain
the ratio. If the HO2S1 transition time ratio is not within the
range, Diagnostic Trouble Code (DTC) P1134 will be set,
indicating that the HO2S1 is not responding as expected
to changes in exhaust oxygen content.
Conditions for Setting the DTC
S HO2S1 rich–to–lean and lean–to rich transition ratio
is out of specification(between 0.375 and 3.5).
S Closed Loop stoichiometry.
S Engine Coolant Temperature (ECT) is greater than
70°C (158°F).
S System voltage is greater than 10 volts.
S Engine run time is greater than 60 seconds.
S Purge Duty Cycle (DC) is less than 20%.S Engine speed is between 1600 and 4300 rpm.
S Calculated airflow is between 9 and 40 g/sec.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0131, P0132, P0134, P0135,
P1167, P0171, P1171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P1404, P0405, P0406,
P0506, P0507, and P0443 are not set.
S 2 second delay after conditions are met.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The vehicle will operate in Open Loop.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.

Page 790 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual 1F – 544IENGINE CONTROLS
DAEWOO V–121 BL4
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
A malfunction in the

1F – 544IENGINE CONTROLS
DAEWOO V–121 BL4
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
A malfunction in the HO2S1 ignition feed or ground circuit
may cause a DTC P1134 to set. Check HO2S1 circuitry for
intermittent faults or poor connections. If connections and
wiring are OK and DTC P1134 continues to set, replace
the HO2S1.
Reviewing the Failure Records vehicle mileage since the
diagnostic test last failed may help determine how open
the condition that caused the DTC to be set occurs. This
may assist in diagnosing the condition.Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Chart.
3. A condition that affects pre–converter and post–
converter oxygen sensors indicates probable con-
tamination. To avoid damaging replacement sen-
sors, correct the condition which caused the
contamination before replacing the affected sen-
sors.
5. This step checks for conditions which may cause
the oxygen sensor to appear faulty. Correct any of
the described conditions if present.
8. To avoid damaging replacement sensors, correct
the condition which caused the contamination be-
fore replacing the affected sensors
DTC P1134 – Front Heated Oxygen Sensor (HO2S1) Transition
Ratio
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Important : If any Diagnostic Trouble Codes (DTCs)
are set, refer to those DTCs before processing with
this diagnostic chart.
1. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine and idle at normal operating
temperature.
3. Operate the engine within parameters specified
under Conditions for Setting the DTC.
4. Using a scan tool, monitor specific DTC info for
DTC P1134 until the DTC P1134 test runs.
5. Note the test result.
Does the scan tool indicate DTC P1134 failed this
ignition?–Go to Step 3Go to
”Diagnostic
Aids”
3Perform an exhaust system leak test.
If an exhaust leak is found, repair as needed.
The exhaust leak isolated?–Go to Step 14Go to Step 4
4Visually/physically inspect for the following items:
S Front Heated Oxygen Sensor (HO2S1) is se-
curely installed.
S Corrosion on the terminals.
S Terminal tension.
S HO2S1 wiring harness for poor terminal con-
nection or damaged wiring.
Is a problem found in any of the above areas?–Go to Step 7Go to Step 5

Page 791 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual ENGINE CONTROLS 1F – 545
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
51. Turn the ignition OFF.
2. Disconnect the HO2S1 connector.
3. Turn the ignition ON.
4. Using a voltmeter, measure the v

ENGINE CONTROLS 1F – 545
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
51. Turn the ignition OFF.
2. Disconnect the HO2S1 connector.
3. Turn the ignition ON.
4. Using a voltmeter, measure the voltage be-
tween following terminals.
5. Terminal 4 of Engine Control Module (ECM)
side HO2S1 connector and ground.
6. Terminal 3 of ECM side HO2S1 connector and
ground.
Are both voltages in the specified value?3–5 vGo to Step 6Go to Step 8
61. With the HO2S1 disconnected, jumper the
ECM side HO2S1 connector terminals 4 and 3.
2. Turn the ignition ON.
3. Using a scan tool, monitor the HO2S1 voltage.
Does the scan tool indicates less than 10 millivolts
and immediately return to about 450 millivolts when
the jumper is removed?–Go to Step 10Go to Step 9
7Repair conditions as needed.
Is the action complete?–Go to Step 14–
8Check for faulty ECM connections or terminal dam-
ages and repair as needed.
Is the repair complete?–Go to Step 14Go to Step 9
9Repair open, short, or grounded signal circuit.
Is the repair complete?–Go to Step 14Step 11
10Remove the HO2S1 and examine it for sign of:
S Fuel contamination.
S Improper room temperature vulcanizing sealant
(white powdery coating on the sensor)
S Engine oil/coolant consumption.
Are sign of contamination observed?–Go to Step 12Go to Step 13
111. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 14Go to Step 13
12Determine and correct the cause of contamination.
Is the repair complete?–Go to Step 14
13Replace the HO2S1.
Is the repair complete?–Go to Step 14–
141. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 15Go to Step 2
15Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

Page 792 of 2643

DAEWOO NUBIRA 2004 Service Repair Manual 1F – 546IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1167
FRONT HEATED OXYGEN SENSOR (HO2S1) RICH IN
DECEL FUEL CUTOFF (DFCO)
Circuit Description
The Engine Control Module (ECM

1F – 546IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1167
FRONT HEATED OXYGEN SENSOR (HO2S1) RICH IN
DECEL FUEL CUTOFF (DFCO)
Circuit Description
The Engine Control Module (ECM) supplies a voltage of
about 0.45 volts between terminals M12 and M29 (if mea-
sured with a 10 megohm digital voltmeter, this may read
as low as 0.32 volts). The Front Heated Oxygen Sensor
(HO2S1) varies the voltage within a range of about 1 volt
if the exhaust is rich, down through about 0.10 volts if the
exhaust is lean.
In internal circuitry of the Engine control Module (ECM)
can identify if the vehicle fuel system is capable of cutoff
amount of the fuel supply during deceleration. When a De-
cel Fuel Cutoff (DFCO) mode of operation is requested
during Closed Loop operation, the ECM will cutoff the fuel
supply to the engine. Under these conditions the ECM
should detect a lean condition. If the ECM detect a rich
condition at this time, Diagnostic Trouble Code (DTC)
P1167 will set. Damaged fuel pressure regulator and faulty
injector will be the cause of this DTC.
Conditions for Setting the DTC
S HO2S1 voltage is greater than 0.55 volts in Decel
Fuel Cutoff (DFCO) mode.
S System voltage is greater than 10 volts.S Engine Coolant Temperature (ECT) is greater than
60°C (140°F)
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P0405, P0406, P0506,
P0507, P1404, and P0443 are not set.
S 3 second delay after in DFCO mode.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The vehicle will operate in Open Loop.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC can be cleared by using the scan tool.

Load next 8 pages

Page: < prev 1-10 ... 753-760 761-768 769-776 777-784 785-792 793-800 801-808 809-816 817-824 ... 2648 next >

spare tire location lug pattern key fob odometer towing open hood