1995 ACURA TL Service Repair Manual

SRS Indicato r Ligh t Wir e Connection s
SRS Indicato r Ligh t Powe r Circui t
To UNDER-DAS HFUSE/RELAY BO X
18 P CONNECTO R
To GAUG E ASSEMBL Y
DASHBOAR D WIR E HARNES S
SRS Indicato r Ligh t Contro l Circui t
To SR S UNI T
SRS MAI N HARNES S
C801
To UNDER-DAS H
FUSE/RELA Y BO X
2 P CONNECTO R
C421
C427
C60 1
C42 1 : MAI N WIR E HARNES S 3 P CONNECTO R C80 1 : SR S MAI N HARNES S 2 P CONNECTO R
C42 7 : MAI N WIR E HARNES S 16 P CONNECTO R C80 2 : SR S MAI N HARNES S 3 P CONNECTO R
C60 1 : DASHBOAR D WIR E HARNES S 16 P CONNECTO R C80 5 : SR S MAI N HARNES S 18 P CONNECTO R
C60 3 : DASHBOAR D WIR E HARNES S 18 P CONNECTO R
C61 5 : DASHBOAR D WIR E HARNES S 5 P CONNECTO R
C615
C802
MAIN WIR E HARNES S
C805
DASHBOARD WIR E
HARNES S
C615C60 3
To GAUG E ASSEMBL Y
ProCarManuals.com

Airbag

Replacement

After a collision in which the airbags were deployed, the

airbag assemblies and the SRS unit must be replaced.

Store a removed airbag assembly with

the pad surface up. If the airbag is improperly stored

face down, accidental deployment could propel the unit

with enough force to cause serious injury.

CAUTION:

Always disconnect the airbag connectors when the

SRS main harness is disconnected.

'96 Model: Always keep the short connector (RED) on

the passenger's airbag when the harness is discon-

nected.

Do not disassemble or tamper with the airbag.

NOTE:

Do not install used SRS parts from another vehicle.

When repairing, use only new SRS parts.

Carefully inspect the airbag before you install it. Do

not install an airbag that shows signs of being

dropped or improperly handled, such as dents, cracks

or deformation.

1. Make sure you have the anti-theft code for the radio,

then write down the frequencies for the radio's pre-

set buttons.

2. Disconnect the battery negative cable, then discon-

nect the positive cable from the battery, and wait at

least three minutes.

3. Disconnect the airbag connectors:

Driver's Side:

Remove the access panel from the steering wheel,

then disconnect the 2P connector between the driver's

airbag and cable reel.

ACCESS

PANEL
Front Passenger's Side:

'96 Model:

Remove the glove box, then remove the short connec-

tor (RED) from it's holder.

Disconnect the 3P connector between the front pas-

senger's airbag and SRS main harness, then connect

the short connector (RED) to the airbag side of the con-

nector.

FRONT PASSENGER'S

AIRBAG

3P CONNECTOR
SHORT CONNECTOR (RED)

SRS MAIN HARNESS

'97 - 98 Models:

Remove the glove box.

Disconnect the 2P connector between the front pas-

senger's airbag and SRS main harness.

FRONT PASSENGER'S AIRBAG

2P CONNECTOR

SRS MAIN HARNESS

2P CONNECTOR

DRIVER'S AIRBAG

2P CONNECTOR
CABLE REEL

2P CONNECTOR
DRIVER'S

AIRBAG.ProCarManuals.com

4. Remove the airbags:

Driver's Side:

Remove the two Torx bolts using a Torx T30 bit, then

remove the driver's airbag.

DRIVER'S

AIRBAG

CRUISE

CONTROL

SET/RESUME

SWITCH

TORX BOLTS

Use a Torx T30 bit.
Front Passenger's Side:

Remove the four mounting nuts from the bracket.

Remove the bracket and one mounting nut, then lift

the front passenger's airbag out of the dashboard.

NOTE: The lid of the airbag has pawls on its side which

attach it to the dashboard. To remove the airbag, cover

the lid and dashboard with a cloth, and pry carefully

with a flat tip screwdriver.

FRONT PASSENGER'S

AIRBAG

BRACKET

BRACKET

MOUNTING NUTS

FRONT PASSENGER'S

AIRBAG

MOUNTING NUTSProCarManuals.com

Airbag

Replacement (cont'd)

CAUTION: Be sure to install the SRS wiring so that it is

not pinched or interfering with other parts.

5. Install the new airbags:

Driver's Side: Place the driver's airbag in the steering

wheel, and secure it with new Torx bolts.

TORX BOLTS

9.8 N-m (1.0 kgf-m, 7.2 Ibf-ft)

Replace.

Use a Torx T30 bit.

DRIVER'S AIRBAG
Front Passenger's Side:

Place the front passenger's airbag into the dash-

board.

Tighten the middle airbag mounting nut, then install

the bracket and four mounting nuts.

Tighten the two outer airbag mounting nuts first,

then tighten the two bracket mounting nuts.

FRONT PASSENGER'S

AIRBAG

FRONT PASSENGER'S

AIRBAG MOUNTING NUT

(MIDDLE)

9.8 N-m (1.0 kgf-m, 7.2 Ibf-ft)

Replace.

BRACKET

MOUNTING NUTS

9.8 N-m (1.0 kgf-m, 7.2 Ibf-ft)

Replace.

FRONT PASSENGER'S

AIRBAG

MOUNTING NUTS

9.8 N-m (1.0 kgf-m, 7.2 Ibf-ft)

Replace.ProCarManuals.com

6. Reconnect the airbag connectors.

Front Passenger's Side:

'96 Model:

Attach the short connector (RED) to the connector

holder, then reinstall the glove box.

SHORT CONNECTOR

(RED) /HOLDER

FRONT PASSENGER'S

AIRBAG

3P CONNECTOR
SRS MAIN HARNESS

3P CONNECTOR

'97-98 Models:

Attach the airbag connector to the connector holder,

then install the glove box.

SRS MAIN HARNESS

2P CONNECTOR

FRONT PASSENGER'S

AIRBAG

2P CONNECTOR
Driver's Side:

Connect the driver's airbag 2P connector to the cable

reel 2P connector, then install the access panel on the

steering wheel.

CABLE REEL

2P CONNECTOR

ACCESS PANEL

DRIVER'S AIRBAG

2P CONNECTOR

7. Connect the battery positive cable, then connect the

negative cable.

8. After installing the airbag, confirm proper system

operation:

Turn the ignition switch ON (II); the SRS indicator

light should come on for about six seconds and

then go off.

Make sure both horn buttons work.

Take a test-drive, and make sure the cruise con-

trol switches work.

9. Enter the anti-theft code for the radio, then enter the

customer's radio station presets.ProCarManuals.com

Airbag
Disposa l
Before scrappin g an y airbag s (includin g thos e in a whol e
vehicl e t o b e scrapped) , th e airbag s mus t b e deployed . I f
th e vehicl e i s stil l withi n th e warrant y period , befor e yo u
deplo y th e airbags , th e Acur a Distric t Technica l Manage r
must giv e approva l and/o r specia l instructions . Onl y afte r
th e airbag s hav e bee n deploye d (a s th e resul t o f vehicl e
collision , fo r example) , ca n the y b e scrapped . I f th e
airbag s appea r intac t (no t deployed) , trea t the m wit h
extrem e caution . Follo w thi s procedure :
Deployin g th e Airbags : In-vehicl e
NOTE : I f a n SR S vehicl e is t o b e entirel y scrapped , it s air -
bag s shoul d b e deploye d whil e stil l i n th e vehicle . Th e
airbag s shoul d no t b e considere d a s salvageabl e part s
an d shoul d neve r b e installe d in anothe r vehicle .
Confir m tha t eac h airba g assembl y i s
securel y mounted ; otherwise , sever e persona l injur y
coul d resul t fro m deployment .
1 . Mak e sur e yo u hav e th e anti-thef t cod e fo r th e
radio , the n writ e dow n th e frequencie s fo r th e
radio' s prese t buttons .
2 . Disconnec t th e batter y negativ e cable , the n discon -
nec t th e positiv e cable .
3 . Confir m tha t th e specia l too l i s functionin g properl y
by followin g th e chec k procedur e o n th e labe l o n
the too l o r th e procedur e o n pag e 24-51 .
Driver' s Airbag :
4 . Remov e th e acces s panel , the n disconnec t th e 2 P
connecto r betwee n th e driver' s airba g an d th e cabl e
reel .
DRIVER' SAIRBAGCABLE REE L2P CONNECTO R
ACCESSPANEL
DRIVER' S AIRBA G
2 P CONNECTO R
Front Passenger' s Airbag :
5.Remov e th e glov e box , the n disconnec t th e 2 P o r 3 P
connecto r betwee n th e fron t passenger' s airba g an d
SR S mai n harness .
SRS MAI N HARNES SCONNECTO R
6.
FRON T PASSENGER' SAIRBAGCONNECTO R
Cut of f th e airba g connector , stri p th e end s o f th e
airba g wires , an d connec t th e specia l too l alligato r
clip s t o th e airbag . Plac e th e specia l too l approxi -
matel y thirt y fee t (1 0 meters ) awa y fro m th e airbag .
DRIVER' SAIRBAG
FRONT
PASSENGER' S
AIRBAG
ALLIGATO RCLIPS(Yellow )
12 VOL T BATTER Y
ALLIGATO RCLIPS(Yellow )
OPERATIO N
SWITC H
DEPLOYMEN T
TOO L
07HA Z - SG0040 0
ProCarManuals.com

7. Connec t a 12 vol t batter y to th e tool :
If th e gree n ligh t o n th e too l come s on , th e air -
ba g ignite r circui t i s defectiv e an d canno t deplo y
th e airbag . G o t o Damage d Airba g Specia l
Procedure .
If th e re d ligh t o n th e too l come s on , th e airba g i s
read y t o b e deployed .
8 . Pus h th e tool' s deploymen t switch . Th e airba g
shoul d deplo y (deploymen t i s bot h highl y audibl e
an d visibl e a lou d nois e an d rapi d inflatio n o f th e
bag , followe d b y slo w deflation) .
If audible/visibl e deploymen t happens , an d th e
gree n ligh t o n th e too l come s on , continu e wit h
this procedure .
I f th e airba g doesn' t deploy , ye t th e gree n ligh t
come s ON , it s ignite r i s defective . G o t o Dam -
age d Airba g Specia l Procedure .
Durin g deployment , th e airba g ca n becom e ho t
enoug h t o bur n you . Wai t thirt y minute s afte r
deploymen t befor e touchin g th e airbag .
9 . Dispos e o f th e complet e airbag . N o par t o f i t ca n b e
reused . Plac e i t i n a sturd y plasti c bag , an d sea l i t
securely .
CAUTION :
Wea r a fac e shiel d an d glove s whe n handlin g a
deploye d airbag .
Was h you r hand s an d rins e the m wel l wit h
wate r afte r handlin g a deploye d airbag .
AIRBAG
Deployin g th e Airbag : Out-of-vehicl e
I f a n intac t airba g ha s bee n remove d fro m a scrappe d
vehicle , o r ha s oee n foun d defectiv e o r damage d durin g
transit , storag e o r service , i t shoul d b e deploye d a s fol -
lows :
1 . Confir m tha t th e specia l too l i s functionin g properl y
b y followin g th e chec k procedur e o n thi s pag e o r o n
th e too l label .
2 . Positio n th e airba g fac e up , outdoor s o n fla t groun d a t
leas t thirt y fee t (10m ) fro m an y obstacle s o r people .
3 . Follo w step s 5 , 6 , 7 , an d 8 of th e In-vehicl e deploy -
men t procedure .
Damage d Airba g Specia l Procedur e
I f a n airba g canno t b e deployed , i t shoul d
no t b e treate d a s norma l scrap ; i t shoul d stil l b e consid -
ere d a potentiall y explosiv e devic e tha t ca n caus e seri -
ou s injury .
1 . I f installe d i n a vehicle , follo w th e remova l proce -
dur e o n pag e 24-47 .
2 . I n al l cases , mak e a shor t circui t b y twistin g togethe r
th e tw o airba g inflato r wires .
3 . Packag e th e airba g i n exactl y th e sam e packagin g
tha t th e ne w replacemen t par t cam e in .
4 . Mar k th e outsid e o f th e bo x "DAMAGE D AIRBA G
NO T DEPLOYED " s o i t doe s no t ge t confuse d wit h
you r part s stock .
5 . Contac t you r Acur a Distric t Technica l Manage r fo r
ho w an d wher e t o retur n i t fo r disposal .
Deploymen t Tool : Chec k Procedur e
1 . Connec t th e yello w clip s t o bot h switc h protecto r
handle s o n th e tool ; connec t th e too l t o a battery .
2 . Pus h th e operatio n switch : gree n mean s th e too l i s
OK ; re d mean s th e too l i s faulty .
3 . Disconnec t th e batter y an d th e yello w clips .
ProCarManuals.com

Cable Ree l
Replacemen t
Store a remove d airba g wit h th e pa d sur -
fac e up . I f th e airba g i s improperl y store d fac e down ,
accidenta l deploymen t coul d prope l th e uni t wit h
enoug h forc e to caus e seriou s injury .
CAUTION :
Alway s disconnec t th e airba g connecto r whe n th e
SR S mai n harnes s is disconnected .
D o no t disassembl e o r tampe r wit h th e airbag .
NOTE : Carefull y inspec t th e airba g befor e installin g it .
D o no t instal l a n airba g tha t show s sign s o f bein g
droppe d o r improperl y handled , suc h a s dents , crack s o r
deformation .
1 . Mak e sur e yo u hav e th e anti-thef t cod e fo r th e
radio , the n writ e dow n th e frequencie s fo r th e
radio' s prese t buttons .
2. Disconnec t th e batter y negativ e cable , the n discon -
nec t th e positiv e cabl e fro m th e battery , an d wai t a t
leas t thre e minutes .
3 . Remov e th e acces s pane l fro m th e steerin g wheel ,
the n disconnec t th e 2 P connecto r betwee n th e driv -
er' s airba g an d cabl e reel .
DRIVER' SAIRBAG
CABLE REE L
2 P CONNECTO R
ACCESSPANEL
DRIVER' S AIRBA G
2 P CONNECTO R
4. Mak e sur e th e wheel s ar e aligne d straigh t ahead .
5 . Remov e th e dashboar d lowe r cover .
6 . Remov e th e driver' s airba g assembl y fro m th e
steerin g whee l (tw o T3 0 Tor x bolts) .
TORX BOLT S
Us e a Tor x T3 0 bit .
DRIVER' SAIRBAG
DASHBOAR D LOWE R COVE R
ProCarManuals.com