Page 177 of 4171

PRECAUTIONSADP-163
< PRECAUTION >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
5. When the repair work is completed, return the ignition switch to the ″LOCK ″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of al l control units using CONSULT-III.
Precaution for WorkINFOID:0000000003775660
When removing or disassembling each component, be ca reful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
Protect the removed parts with a shop cloth and keep them.
Replace a deformed or damaged clip.
If a part is specified as a non-reusable part, always replace it with new one.
Be sure to tighten bolts and nuts securely to the specified torque.
After re-installation is completed, be sure to check that each part works normally.
Follow the steps below to clean components.
- Water soluble foul: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the fouled area.
Then rub with a soft and dry cloth.
- Oily foul: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the fouled area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with
a soft and dry cloth.
Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
For genuine leather seats, use a genuine leather seat cleaner.
Revision: December 20092009 QX56
Page 178 of 4171
ADP-164
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service ToolINFOID:0000000003775662
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service ToolINFOID:0000000003775663
Tool number
(Kent-Moore No.)
Tool name Description
—
(J-39570)
Chassis ear Locating the noise
—
(J-43980)
NISSAN Squeak and Rattle
Kit Repairing the cause of noise
SIIA0993E
SIIA0994E
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear Locating the noise
SIIA0995E
Revision: December 20092009 QX56
Page 179 of 4171
DRIVER SEAT CONTROL UNITADP-165
< ON-VEHICLE REPAIR >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
ON-VEHICLE REPAIR
DRIVER SEAT CONTROL UNIT
Removal and InstallationINFOID:0000000005848469
REMOVAL
NOTE:
The driver seat control unit is part of the driver seat.
1. Remove the driver seat. Refer to SE-50, "Removal and Installation"
.
2. Disconnect driver seat control unit electrical connector.
3. Remove driver seat control unit from driver seat.
INSTALLATION
Installation is in the reverse order of removal.
Revision: December 20092009 QX56
Page 180 of 4171
ADP-166
< ON-VEHICLE REPAIR >
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
Removal and InstallationINFOID:0000000004055980
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
REMOVAL
1. Disconnect the battery negative terminal.
2. Remove the instrument driver lower panel. Refer to IP-13, "Removal and Installation"
.
3. Remove the screw from the aut omatic drive positioner control
unit (1).
4. Remove automatic drive positioner control unit (1) from bracket
and disconnect electrical connectors.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Clamp the harness in position.
NOTE:
After installing the automatic drive positioner cont rol unit, perform additional service when disconnecting bat-
tery negative terminal. Refer to ADP-8, "Special Repair Requirement"
.
ALIIA0241ZZ
Revision: December 20092009 QX56
Page 181 of 4171
SEAT MEMORY SWITCHADP-167
< ON-VEHICLE REPAIR >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SEAT MEMORY SWITCH
Removal and InstallationINFOID:0000000004055981
Refer to INT-11, "Removal and Installation" for removal and installation of seat memory switch.
Revision: December 20092009 QX56
Page 182 of 4171
ADP-168
< ON-VEHICLE REPAIR >
DOOR MIRROR REMOTE CONTROL SWITCH
DOOR MIRROR REMOTE CONTROL SWITCH
Removal and InstallationINFOID:0000000004055982
The door mirror remote control switch is part of the power window switch assembly. Refer to INT-11, "Removal
and Installation" for removal and installation of door mirror remote control switch.
Revision: December 20092009 QX56
Page 183 of 4171
PEDAL ADJUSTING MOTORADP-169
< ON-VEHICLE REPAIR >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
PEDAL ADJUSTING MOTOR
Removal and InstallationINFOID:0000000004055983
Refer to ACC-4, "Removal and Installation" for accelerator pedal and BR-19, "Removal and Installation" for
brake pedal when removing pedal adjusting motors.
Revision: December 20092009 QX56
Page 184 of 4171
ADP-170
< ON-VEHICLE REPAIR >
TILT SWITCH
TILT SWITCH
Removal and InstallationINFOID:0000000004055984
REMOVAL
1. Disconnect battery negative terminal.
2. Remove the instrument lower panel LH. Refer to IP-12, "Exploded View"
.
3. Remove steering column cover lower. Refer to IP-12, "Exploded View"
.
4. Disconnect tilt switch electrical connector.
5. Remove tilt switch from lower column cover.
INSTALLATION
Installation is in the reverse order of removal.
Revision: December 20092009 QX56