1995 NISSAN ALMERA N15 Service Manual

TROUBLEDIAGNOSIS FORNON-DETECTABLE ITEMS

Park/Neutral PositionSwitch(Cont'd)

GA 16DE forAustralia

EC-PNP/SW-01

AIT
models

MIT
models
Detectable line
fa/"' DTC
Non-detectable line forDTC

ill
:

@:

-:
-:

• INHIBITOR
P __ ..1SWITCH

R N--D 2~:
ill

l4=Jl
B

I

B

Qj:
B


-cM>--O--'-,
BB

~ ~

~ @D

ECM

(ECCSCONTROL
MODULE)

(IT)

NEUTRAL POSITION
SWITCH

(E220):
@

NEUT

1
2•2
1

G/OR

I

G/OR

1$11
CEID

@

G/OR

1$1

~

G/OR

I
~@D

O- G/OR
-ca
G/OR---

t

G/OR

[b,~

=r@D

G/OR

I

G/OR

m

OTHER --

~(222)

~ GY
fTIffiI
~B
Refer
tolast page
(Foldout page).

CHID
(E10t)

,

101 102 103
107 108109
113 114
115 104
105 106
110 111 112
116
117
118

HEC079
EC-174

•

Neutral
position switch

INSPECTION START
DIAGNOSTIC
PROCEDURE
SHIFT
OUT OFNIP-RANGETROUBLE
DIAGNOSIS FORNON-DETECTABLE ITEMS
@J

Park/Neutral PositionSwitch
(Cont'd)

When thegear position is"P"
(A/T
models only)or
"N",
parkl
neutral position switchis"ON",
ECM detects thepark/neutral positionwhencontinuity with
ground exists,

• NEUTRAL SWCIRCUIT.
THEN
TOUCH START
MEF983ESEF206L
~ CONNECT~
JA

L41E)~~

1=1
=E=CM~E CONNECTOR!'

35 22
INSPECTION
END
OK
Turn ignition switch"OFF".
NG
CHECK
OVERALL FUNCTION.
(ijJ\ 1.Turn ignition switch"ON".
~ 2.Perform "NEUTRAL SW
CIRCUIT" or"NEUTRAL POSI
SW CKT" in"FUNCTION
TEST" modewithCONSULT.
OR

rF.I\
2.Check "NEUTRAL SW"or
~ "NEUTPOSISW"signal in
"DATA MONITOR" modewith
CONSULT.

Neutral position: ON
Except above:OFF

OR

fff\
1.Set shift lever tothe neutral
~ position.
2. Disconnect ECMharness con-
nector.
3. Check harness continuity
between ECMterminal
@
or
@ and body ground.

Continuity shouldexist.

If OK, check harness forshort.
SEF236R
r:'I

.;,

i,MONITOR
*NOFAIL
0

START SIGNAL ON
CLOSED TH/POS ON
/lIR COND SIGOFF
NEUT POSISW ON

[ RECORD

@:
Fo'Australia

@:
Except forAustralia

__
II
START
CHECKGROUND CIRCUIT.
1. Disconnect neutralposition switch
harness connector.
2. Check harness continuity between
terminal @and body ground.

Continuity shouldexist.

If OK, check harness forshort.
OK NG
Check thefollowing.
• Harness connectors

@,(@)

• Harness foropen or
short between neutral
position switchand
body ground
If NG, repair harness or
connectors.
SEF5020 EC-175

TROUBLEDIAGNOSIS FORNON-DETECTABLE ITEMS
Park/Neutral PositionSwitch(Cont'd)

Il
~io

ECM
E[coNNECTORII

35 22
~iV

m
@

Disconnect ECMharness con-
nector.

@:
ForAustralia
35 :Except forAustralia
SEF177R
CHECK
INPUTSIGNAL CIRCUIT.
1. Check harness continuity between
ECM terminal
@
or
@
and terminal

CD.

Continuity shouldexist.
If
OK, check harness forshort.

OK

CHECK COMPONENT
(Neutral positionswitch).
Refer to"Check ofPosition Switch"of
"ON-VEHICLE SERVICE"inMT section.

OK

Disconnect andreconnect harnesscon-
nectors inthe circuit. Thenretest.
Trouble isnot fixed.
Check ECMpinterminals fordamage
or the connection ofECM harness con-
nector. Reconnect ECMharness con-
nector andretest.
INSPECTION END

EC-176 NG
NG
Check
thefollowing.
• Harness connectors

@,@

• Harness connectors

@,@!)

• Harness connectors

@),CmD

• Harness foropen or
short between ECM
and neutral position
switch
" NG, repair harness or
connectors.
Replace neutralposition
switch.

TROUBLEDIAGNOSIS FORNON-DETECTABLE ITEMS
Park/Neutral PositionSwitch(Cont'd)
• PARKJNEUT POSISWCKT • Inhibitor
switch
MEF983E

I

NEXT
II__
ST:_A_RT __
I

MEC7318

•

INSPECTION
END
OK
INSPECTION
START

"N"
or
"P":
ON
Except above: OFF
OR
1. Shift selector leverto"P"
position.
2. Disconnect ECMharness con-
nector.
3. Check harness continuity
between ECMterminal
@
or
@ and body ground.
Continuity shouldexist.
If OK, check harness forshort
4. Shift selector leverto"N"
position.
5. Check harness continuity
between ECMterminal
@
or
@ and body ground.
Continuity shouldexist.
If OK, check harness forshort

1!1

CHECK OVERALL FUNCTION.

(ij\
1.Turn ignition switch"ON".
~ 2.Perform "NEUTRAL POSISW
CKT" in"FUNCTION TEST"
mode withCONSULT.
OR

rF.I\
2.Check "NEUTRAL SW"or
~ "NEUTPOSISW"signal in
"DATA MONITOR" modewith
CONSULT.
SEF178R

SHIFT

OUT OFNIP-POSITION
THEN
TOUCH START
~rMONITOR ~NOFAIL
0

SlART SIGNAL ON
CLOSED TH/POS ON
'!\IR COND SIGOFF
NEUT POSISW ON

[ RECORD

@ :
For Australia

@ :
Except forAustralia

~i5@a

II
ECM
19'
CONNECTOR
TI

G ...._ CD
3522

~~

~io@a
6iB
NG
Turn ignition switch"OFF"
SEF228R CHECK
GROUND CIRCUIT.
1. Disconnect inhibitorswitchharness
connector.
2. Check harness continuity between
terminal G)and body ground.
Continuity shouldexist.
If OK, check harness forshort. NG
Check thefollowing.
• Harness connectors

@D,@])

• Harness foropen or
short between inhibitor
switch andbody ground

If
NG, repair harness or
connectors.
OK
Disconnect ECMharness con-
nector.
EC-177