1995 NISSAN ALMERA N15 Service Manual

EXTERIOR

CD ~
Hood frontsealing rubber

SEC. 650
CID

Windshield uppermolding
SEC. 720

@lJ
SBF342H

(ID

@
Cowl topseal andcowl topgrille

SEC. 660
1
Cutoffsealant atglass end.
2. Clean theside onwhich panelwasmounted.
3. Setmolding fastener andapply primer tobody
panel, andapply sealant tobody.
4. Install molding byaligning themolding mark
located oncenter withvehicle center.
Be sure toinstall tightly sothat there isno gap
around thecorner.
(f)
Drip weatherstrip

58T061
58T062

Cowl
topseal
Hood
frontsealing rubber

CID
Windshield sidemolding
Mounted with
screws,
SEC.720
Door
panel

SBT063
•

8T-29

EXTERIOR

r
Sunroof rail
assembly

l

SBF349H
Front
Sun
roof lid
weatherstrip
Roof panel
SBT067

@

Door outside molding
Front door

SEC. 800 Screw'
III

~" g.@~

Door outer molding ~__

~/CIiP
~"..-/f'yoor outerpanel

Rear door ~
c:?

SEC. 820
~J

s,,~,~)

\.~ ~' "',,mold'"
CIIP~~

Door panel --~

~ 0

@
Sunroof lidweath .

S
erstnp

EC.736

SBT043
SBF455EA

d;!)de

(\

@

\\
@

\\

@

.........
\
\

@

\\

@

II

@

u

~~

::€t)£j

I.

II

.~) I

:
Front dooronly

CID
Door weatherstrip
SEC. 800.820
@
Body sidewelt

SEC. 769

@
Front doo .
r parting seal
SBT065
8T-30

EXTERIOR

•

SBT069
SBT070

Back doorwindow molding
Bonding
portion

@
Trunk lidweatherstrip
SEC. 843
@ Back doorsidesealing rubber

SEC. 909

@ Back doorwindow molding
SEC. 900
SBT06B

Heat
gun
•
;Double-faced adhesivetape

~~~~ ..

-----~
.

~.: ..

~-o

~.
"----'
-.-/

'-

3-door

@J

Side guard molding
SEC. 766
4-door and5-door
• With avehicle coatedwithHard Clear Coat,
use double-faced 3Madhesive tapeProduct
No. 4210 orequivalent, afterpriming with3M
primer Product No.N-200 orC-100 orequiva-
lent.

@
Rear window uppermolding andside
molding

Basically thesame aswindshield uppermolding.

Refer to@ Windshield uppermolding.
@ Rear window lowermolding

Mounted withscrews.

Removal:Removemolding
by
cutting around itsperimeter.
Installation: Referto"Back doorwindow."

MBF13BAA

8T-31

@l
Back doorweatherstrip

SEC. 900

Vehicle center
Bondingportion
SBT072

@
Rear combination lamp.
dithnuts andbutyl sealant.
b' ation lamps areInstalle
w

• Rear com In

SEC. 265

BT-32

EXTERIOR
@
Front airspoiler

SEC. 960
8BT074
@
Front struttower barassembly

SEC. 401

[OJ:
N.m (kg-m, ft-lb)

8BT099
•

CAUTION:
Do not remove frontstruttower barassembly whilevehicle isjacked upwith wheels on.

8T-33

EXTERIOR

@
Rear airspoiler

• When installing, makesurethatthere arenotgaps orwaves atends ofair spoiler.
• Before installing spoiler,cleanandremove oilfrom surface wherespoiler willbemounted.

4-door sedan

SEC. 960

Sealingrubber
SBT075
3-door and5-door hatchback

SEC. 960
8T-34
Double-laced
adhesivelape
SBT076

SEAT

• When removing orinstalling theseat trim, carefully handleitto keep dirtoutand avoid damage.

* For Wiring Diagram, referto"POWER SEAT"inEL section.
Front Seat

SEC. 870

l"l
43•55 (4.4 •5.6, 32.~ \

\ t"J :'-
55 ~
L

~4.4 -5.6, 32•41)

~~@~. ~
---

iTiln> __

m
/

I: '

m ~\

tOJ
43-55 ~'}

(4.4 -5.6, 32•41)

~ 21-26 (2.1 -2.7, 15.20)

~,

~ :N.m (kg-m, ft-Ib)

SBT077
8T-35
•

SEAT
Heated Seat

• When handling seat,beextremely carefulnottoscratch heating unit.
• Toreplace heatingunit,seattrimandpadshould beseparated.
• Donot use anyorganic solvent, suchasthinner, benzene, alcohol,gasoline, etc.toclean trims.

Seatback heatingunitremoval
&
installation
Heating
unit Seat
back trim
Trim temperature Increasing
to
Decreasing to
0C (OF) 35
-45
15-25
(95 -113)
(59-77)
Thermostat OFFON
operation
SBF424H
* For Wiring Diagram, referto"HEATED SEAT"inEL section.
8T-36