Page 169 of 1807
BE1L3-01
Z09193
Z14750
OFF
ON
N16845
- BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE-13
1991 Author: Date:
1997 SUPRA (RM502U)
INSPECTION
1. INSPECT IGNITION SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK-No continuity
ACC5 - 7Continuity
ON4 - 5 - 7, 2 - 3Continuity
START4 - 7 - 8, 1 - 2 - 3Continuity
If continuity is not as specified, replace the switch.
2. INSPECT KEY UNLOCK WARNING SWITCH CONTI-
NUITY
ConditionTester connectionSpecified condition
SW OFF
(Key removed)-No continuity
SW ON (Key set)1 - 2Continuity
If continuity is not as specified, replace the switch.
3. Key Unlock Warning System:
INSPECT INTEGRATION RELAY OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1, the negative (-) lead to terminals 5 and 10..
(b) Check the buzzer sounds when the negative (-) lead from
the battery is connected to terminal 6..
If operation is not as specified, replace the relay.
Page 170 of 1807

Z07373
Junction Block Side
Connector ºAº
Wire Harness Side
Connector ºBº BE-14
- BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCH
1992 Author: Date:
1997 SUPRA (RM502U)
4. INSPECT RELAY CIRCUIT
Light Auto Turn Off System:
Remove the relay from junction block and inspect the connec-
tors on the wire harness and junction block side, as shown in
the chart.
Tester connectionConditionSpecified condition
A6 - GroundDriver's door courtesy switch OFFNo continuity
A6 - GroundDriver's door courtesy switch ONContinuity
A10 - GroundConstantContinuity
B1 - GroundLight control switch position OFF or TAILNo continuity
B1 - GroundLight control switch position HEADContinuity
B4 - GroundLight control switch position OFFNo continuity
B4 - GroundLight control switch position TAIL or HEADContinuity
A1 - GroundConstantBattery positive voltage
A7 - GroundIgnition switch position LOCK or ACCNo voltage
A7 - GroundIgnition switch position ONBattery positive voltage
B2 - GroundConstantBattery positive voltage
B3 - GroundConstantBattery positive voltage
If the circuit is as specified, try replacing the relay with a new
one.
If the circuit not as specified, inspect the circuits connected to
other parts.
Page 171 of 1807
Z18223
D.R.L. No.3 Relay*
Combination Switch
Light Control SwitchD.R.L. Main Relay* Headlights
Front Side MarkerR/B No.2
Headlight Control Relay
Headlight Control Relay
(D.R.L.No.2 Relay)
HEAD (LH) Fuse
HEAD (RH) Fuse
HEAD (LH-LWR) Fuse*
HEAD (LH-UPR) Fuse*
HEAD (RH-UPR) Fuse*
Integration Relay
J/B No.1
Taillight Relay
GAUGE Fuse
TAIL Relay
Rear Side MarkerRear Combination Lights
: Daytime Running Light
: CANADA models D.R.L. Headlight Dimmer SwitchHEAD (LH-LWR) Fuse*
Taillights
*
BE0DQ-01
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-15
1993 Author: Date:
1997 SUPRA (RM502U)
HEADLIGHT AND TAILLIGHT SYSTEM
LOCATION
Page 172 of 1807
BE0DR-02
Z18244
Spiral Cable Light Control Switch
Connector
BallHeadlight Dimmer Switch
Wiper and
Washer Switch BE-16
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
1994 Author: Date:
1997 SUPRA (RM502U)
COMPONENTS
Page 173 of 1807

Z09366
HEAD
TAIL
Connector ºAºFlash
BE0DS-02
Z09181
34
2 14
3
1
2
Z05930
3
5
21
531 2
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-17
1995 Author: Date:
1997 SUPRA (RM502U)
INSPECTION
1. INSPECT LIGHT CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF-No continuity
TAILA2 - A11Continuity
HEADA2 - A11 - A13Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HEADLIGHT DIMMER SWITCH CONTINU-
ITY
Switch positionTester connectionSpecified condition
FlashA9 - A12 - A14Continuity
Low beamA3 - A9Continuity
High beamA9 - A12Continuity
If continuity is not as specified, replace the switch.
3. INSPECT HEADLIGHT CONTROL RELAY CONTINU-
ITY
ConditionTester connectionSpecified condition
Constant3 - 4Continuity
Apply B+ between
terminal 3 and 4.1 - 2Continuity
If continuity is not as specified, replace the relay.
4. INSPECT TAILLIGHT RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 - 2Continuity
Apply B+ between
terminals 1 and 2.3 - 5Continuity
If continuity is not as specified, replace the relay.
5. Light Auto Turn Off System:
INSPECT INTEGRATION RELAY CIRCUIT (See page
BE-13)
Page 174 of 1807

Z07503
Wire Harness Side
Z09181
34
2 143
12 BE-18
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
1996 Author: Date:
1997 SUPRA (RM502U)
6. INSPECT DOOR COURTESY SWITCH CONTINUITY
(See page BE-28)
7. CANADA models only:
INSPECT D.R.L. MAIN RELAY CIRCUIT
Disconnect the connector from relay and inspect the connector
on wire harness side, as shown.
Tester connectionConditionSpecified condition
5 - GroundHeadlight dimmer switch position Low beam or
high beamNo continuity
5 - GroundHeadlight dimmer switch position FlashContinuity
8 - GroundParking brake switch position OFFNo continuity
8 - GroundParking brake switch position ONContinuity
16 - GroundHeadlight dimmer switch position Low beamNo continuity
16 - GroundHeadlight dimmer switch position Flash or High
beamContinuity
13 - GroundConstantContinuity
18 - GroundConstantContinuity
2 - GroundIgnition switch position LOCK or ACCNo voltage
2 - GroundIgnition switch position ONBattery positive voltage
11 - GroundEngine StopNo voltage
11 - GroundEngine RunningBattery positive voltage
15 - Ground
17 - GroundConstantBattery positive voltage
If the circuit is as specified, try replacing the relay with a new
one.
If the circuit is not as specified, inspect the circuit connected to
other parts.
8. INSPECT D.R.L. NO.2 RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant3 - 4Continuity
Apply B+ between
terminals 3 and 4.1 - 2Continuity
If continuity is not as specified, replace the relay.
Page 175 of 1807
Z14743
Connector B
Connector AB1
B3
B2B4
A1 A5A3 A2
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
BE-19
1997 Author: Date:
1997 SUPRA (RM502U)
9. INSPECT D.R.L. NO.3 RELAY CONTINUITY
Tester connectionConditionSpecified condition
A1 - B3ConstantContinuity
A3 - A5ConstantContinuity
B3 - B4ConstantContinuity
A2 - A5Apply battery positive voltage
between terminal A1 and B3.Continuity
B1 - B2Apply battery positive voltage
between terminal B3 and B4.Continuity
If continuity is not as specified, replace the relay.
10. INSPECT PARKING BRAKE SWITCH CONTINUITY
(See page BE-43)
Page 176 of 1807
BE0DT-01
N09536
Adjusting Screw AAdjusting Screw B
Adjusting Nut C
N08860
Bubble
Acceptable
range
N08861
Acceptable
range BE-20
- BODY ELECTRICALHEADLIGHT AND TAILLIGHT SYSTEM
1998 Author: Date:
1997 SUPRA (RM502U)
ADJUSTMENT
1. Adjusting headlight aim only:
INSPECT HEADLIGHT AIM
Do the following before inspection.
Make sure the body around the headlight is not de-
formed.
Park the vehicle on a level spot.
The driver gets into the driver's seat and puts the
vehicle in a state ready for driving (with a full tank).
Bounce the vehicle several times.
2. Adjusting headlight aim only:
ADJUST HEADLIGHT VERTICAL ALIGNMENT
If the bubble is outside the acceptable range of the beam angle
gauge, adjust it using adjusting screw A.
3. Adjusting headlight aim only:
ADJUST HEADLIGHT HORIZONTAL ALIGNMENT
If the º0º moves away from the mark beyond the acceptable
range, adjust the º0º back to the mark using adjusting screw B.