Page 889 of 4210
![INFINITI QX56 2010 Factory Service Manual DIAGNOSIS SYSTEM (BCM)DLK-55
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
ACTIVE TEST
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Fu nction (BCM - INTELLIGE INFINITI QX56 2010 Factory Service Manual DIAGNOSIS SYSTEM (BCM)DLK-55
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
ACTIVE TEST
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Fu nction (BCM - INTELLIGE](/manual-img/42/57032/w960_57032-888.png)
DIAGNOSIS SYSTEM (BCM)DLK-55
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
ACTIVE TEST
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Fu nction (BCM - INTELLIGENT KEY)INFOID:0000000005380576
DATA MONITOR
CDL UNLOCK SW Indicates [ON/OFF] condition of unlock signal from lock/unlock switch.
CDL LOCK SW Indicates [ON/OFF] condition of lock signal from lock/unlock switch.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
RKE LCK-UNLCK Indicates [ON/OFF] condition of lock/unlock signal at the same time from keyfob.
RKE KEEP UNLK Indicates [ON/OFF] condition of unlock signal from keyfob.
Monitored Item
Description
Test ItemDescription
FLASHER This test is able to check right and left hazard reminder operation. The right hazard lamp turns on
when “RH” on CONSULT-III screen is touched and th e left hazard lamp turns on when "LH" on CON-
SULT-III screen is touched.
POWER WINDOW DOWN This test is able to check power window down operation. The windows are lowered when “ON” on CONSULT-III screen is touched.
HORN This test is able to check panic alarm and horn reminder operations. The alarm activate for 0.5 sec-
onds after “ON” on CONSULT-III screen is touched.
DOOR LOCK This test is able to check door lock operation. The doors lock and unlock based on the item on CON-
SULT-III screen touched.
Monitor Item [Unit] Condition
I-KEY LOCK [ON/OFF] Indicates condition of lock signal from Intelligent Key
I-KEY UNLOCK [ON/OFF] Indicates [condition of unlock signal from Intelligent Key
I-KEY TRUNK [ON/OFF] Indicates condition of trunk open signal fr om Intelligent Key
I-KEY PW DWN [ON/OFF] Indicates condition of all power window signal from Intelligent Key
I-KEY PANIC [ON/OFF] Indicates condition of panic signal from Intelligent Key
PUSH SW [ON/OFF] Indicates condition of ignition knob switch
Revision: April 20092010 QX56
Page 890 of 4210
![INFINITI QX56 2010 Factory Service Manual DLK-56
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (I
NTELLIGENT KEY UNIT)
DIAGNOSIS SYSTEM (INT ELLIGENT KEY UNIT)
CONSULT-III Function (INTELLIGENT KEY)INFOID:00000000053805 INFINITI QX56 2010 Factory Service Manual DLK-56
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (I
NTELLIGENT KEY UNIT)
DIAGNOSIS SYSTEM (INT ELLIGENT KEY UNIT)
CONSULT-III Function (INTELLIGENT KEY)INFOID:00000000053805](/manual-img/42/57032/w960_57032-889.png)
DLK-56
< FUNCTION DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (I
NTELLIGENT KEY UNIT)
DIAGNOSIS SYSTEM (INT ELLIGENT KEY UNIT)
CONSULT-III Function (INTELLIGENT KEY)INFOID:0000000005380577
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with Intelligent Key unit.
SELF-DIAG RESULT
Refer to DLK-196, "DTCIndex".
DATA MONITOR
ACTIVE TEST
Diagnosis mode Function Description
SELF-DIAG RESULTS Displays the diagnosis results judged by Intelligent Key unit.
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from Intelligent Key unit.
DATA MONITOR The Intelligent Key unit input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from Intelligent Key unit.
ECU IDENTIFICATION The Intelligent Key unit part number is displayed.
Monitor Item Condition
PUSH SW Indicates [ON (pushed)/OFF (released)] condition of ignition knob switch.
KEY SW Indicates [ON (inserted)/OFF (removed)] condition of key switch.
DR REQ SW Indicates [ON (pressed)/OFF (released)] co ndition of door request switch (driver side).
AS REQ SW Indicates [ON (pressed)/OFF (released)] condition of door request switch (passenger side).
IGN SW Indicates [ON (ON or START position)/OFF (other than ON and START position)] condition of
ignition switch ON position.
ACC SW Indicates [ON/OFF] condition of ignition switch ACC position.
STOP LAMP SW Indicates [ON/OFF] condition of stop lamp switch.
P RANGE SW Indicates [ON/OFF] position of shift lever park position switch.
DOOR LOCK SIG Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
DOOR UNLOCK SIG Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
KEYLESS PANIC Indicates [ON (pressed)/OFF (released)] condition of Intelligent Key panic button.
KEYLS PBD SIG Indicates [ON (pressed)/OFF (released)] condition of Intelligent Key back door button.
DOOR SW DR Indicates [OPEN/CLOSE] condition of front door switch (driver side) from BCM via CAN com-
munication.
DOOR SW AS Indicates [OPEN/CLOSE] condition of front door switch (passenger side) from BCM via CAN
communication.
DOOR SW RR Indicates [OPEN/CLOSE] condition of rear door switch (RH) from BCM via CAN communication.
DOOR SW RL Indicates [OPEN/CLOSE] condition of rear door switch (LH) from BCM via CAN communication.
DOOR BK SW Indicates [OPEN/CLOSE] condition of back door switch from BCM via CAN communication.
VEHICLE SPEED Displays the vehicle speed signal received from combinatio n meter by numerical value [km/h].
Revision: April 20092010 QX56
Page 891 of 4210
![INFINITI QX56 2010 Factory Service Manual DIAGNOSIS SYSTEM (INTELLIGENT KEY UNIT)DLK-57
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Test item Description
DOOR LOCK/UNLOCK This test is able to check d INFINITI QX56 2010 Factory Service Manual DIAGNOSIS SYSTEM (INTELLIGENT KEY UNIT)DLK-57
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Test item Description
DOOR LOCK/UNLOCK This test is able to check d](/manual-img/42/57032/w960_57032-890.png)
DIAGNOSIS SYSTEM (INTELLIGENT KEY UNIT)DLK-57
< FUNCTION DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Test item Description
DOOR LOCK/UNLOCK This test is able to check door lock/unlock operation.
• ALL UNLK: All door lock actuators are unlocked.
• DR UNLK: Door lock actuator (driver side) is unlocked.
• AS UNLK: Door lock actuator (passenger side) is unlocked.
• BK UNLK: This item is indicated, but inactive.
• LOCK: All door lock actuator is locked.
ANTENNA This test is able to check Intelligent Key antenna operation.
When the following condition are met, hazard warning lamps flash.
• ROOM ANT1: Center console area antenna (rear) and luggage area antenna detect Intelligent Key, when
“ROOM ANT1” is selected.
• ROOM ANT2: Center console area antenna (front) and overhead console area antenna detect Intelligent Key, when “ROOM ANT2” is selected.
• LUG ANT: This selection is not used.
• DR ANT: Outside key antenna (driver side) detects Intelligent Key, when “DR ANT” is selected.
• AS ANT: Outside key antenna (passenger side) detects Intelligent Key, when “AS ANT” is selected.
• BK DR ANT: Outside key antenna (rear bumper) detects Intelligent Key, when “BK DR ANT” is selected.
OUTSIDE BUZZER This test is able to check Intelligent Key warning buzzer operation.
•ON
•OFF
INSIDE BUZZER This test is able to check warning chime in combination meter operation.
• TAKE OUT: Take away warning chime sounds.
• KNOB: Ignition knob switch warning chime sounds.
• KEY: Key warning chime sounds.
•OFF
Revision: April 20092010 QX56
Page 892 of 4210
![INFINITI QX56 2010 Factory Service Manual
DLK-58
< COMPONENT DIAGNOSIS > [WITH
INTELLIGE NT KEY SYSTEM]
U1000 CAN COMM CIRCUIT
CO MPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Descr iptionINFOID:0 000000005146905
CAN (Controller Area Network) INFINITI QX56 2010 Factory Service Manual
DLK-58
< COMPONENT DIAGNOSIS > [WITH
INTELLIGE NT KEY SYSTEM]
U1000 CAN COMM CIRCUIT
CO MPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Descr iptionINFOID:0 000000005146905
CAN (Controller Area Network)](/manual-img/42/57032/w960_57032-891.png)
DLK-58
< COMPONENT DIAGNOSIS > [WITH
INTELLIGE NT KEY SYSTEM]
U1000 CAN COMM CIRCUIT
CO MPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Descr iptionINFOID:0 000000005146905
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
v ehicle is equipped with many ele ct ronic control uni t, and each control unit shares information and links with
other control units during operation (not independent). In CAN communicat ion, control units are connected
wi
th 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of inf ormation transmission with less
wiring
. Each control unit transmits/receives data but selectively reads required data only.
CAN
Communication Signal Chart. Refer to LAN-44, "CAN Communication Signal Chart".
DTC LogicINFOID:0 000000005146906
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0 000000005146907
1.PERFORM SELF DIAGNOSTIC
1.T urn ignition switch ON and wait for 2 second or more.
2. Check “S elf Diagnostic Res ult”.
Is“CAN CO MM CIRCUIT” displayed?
YES>> Refer to LAN-14, " TroubleDiagnosisF low Chart".
NO>> Refer to GI-38, "Intermittent Incident".
DTC CONSULT
-III displa y
description DTC Detection ConditionPossible cause
U100
0C AN COMM CIRCUIT
W hen BCM can not communicate CAN com-
munication s ignal continuously for 2 sec-
onds o r more.
In CAN communication s ystem, any item (or item s)
of the following listed below is malfunctio ning.
•Transmission
•Receiving (ECM)
•R eceiving (VDC/TCS/AB S)
•Receiving (METER/M& A)
•Receiving (TCM)
•Rec eiving (MULTI A V)
•Receiving (IPDM E/R)
Revision: April 2009 2010 QX56
Page 893 of 4210
U1010 CONTROL UNIT (CAN)DLK-59
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
U1010 CONTROL UNIT (CAN)
DTC LogicINFOID:0000000005146908
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000005146909
1.REPLACE BCM
When DTC [U1010] is detected, replace BCM.
>> Replace BCM. Refer to BCS-59, "
Removal and Installation".
Special Repair RequirementINFOID:0000000005146910
1.REQUIRED WORK WHEN REPLACING BCM
The BCM must be initialized when replaced. Refer to BCS-3, "
CONFIGURATION : Description" for BCM con-
figuration.
Initialize NVIS by CONSULT-III. For the details of initialization refer to CONSULT-III operation manual.
>> Work end.
DTC CONSULT-III display de-
scription DTC Detection Condit
ion Possible cause
U1010 CONTROL UNIT (CAN) BCM detected internal CAN communication circuit malfunction. BCM
Revision: April 20092010 QX56
Page 894 of 4210
![INFINITI QX56 2010 Factory Service Manual DLK-60
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
CENTER CONSOLE AREA ANTENNA (REAR)
CENTER CONSOLE AREA ANTENNA (REAR)
DescriptionINFOID:0000000005146911
Detects whether Intelligent Key is INFINITI QX56 2010 Factory Service Manual DLK-60
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
CENTER CONSOLE AREA ANTENNA (REAR)
CENTER CONSOLE AREA ANTENNA (REAR)
DescriptionINFOID:0000000005146911
Detects whether Intelligent Key is](/manual-img/42/57032/w960_57032-893.png)
DLK-60
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
CENTER CONSOLE AREA ANTENNA (REAR)
CENTER CONSOLE AREA ANTENNA (REAR)
DescriptionINFOID:0000000005146911
Detects whether Intelligent Key is inside the vehicle.
Component Function CheckINFOID:0000000005146912
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL
With CONSULT-III
1. Check “ANTENNA” in “Active Test” mode with CONSULT-III.
2. Touch “ROOM ANT1”.
3. When Intelligent Key is in center console area antenna (rear) detection area, hazard lamps flash.
Is the inspection result normal?
YES >> Center console area antenna (rear) is OK.
NO >> Refer to DLK-60, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005146913
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK INSIDE KEY ANTENNA POWER SUPPLY SIGNAL
1. Turn ignition switch OFF.
2. Check signal between Intelligent Key unit connector and ground with an oscilloscope.
Is the inspection result normal?
YES >> Center console area antenna (rear) is OK.
NO >> GO TO 2
2.CHECK INSIDE KEY ANTENNA
1. Disconnect Intelligent Key unit connector and center console area antenna (rear) connectors.
2. Check continuity between Intelligent Key unit harnes s connector (A) M70 terminals 15, 16 and center con-
sole area antenna (rear) harness connector (B) M209 terminals 1, 2.
Test Item Condition Possible cause
ROOM ANT1 An excessive high or low voltage from inside
antenna is sent to the Intelligent Key Unit • Center console area antenna (rear)
• Between Intelligent Key unit and center console area an-
tenna (rear)
Connector Item Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 15 Ground Ignition
switch is
pushed.
ALKIA0585ZZPIIB7441E
Revision: April 20092010 QX56
Page 895 of 4210
![INFINITI QX56 2010 Factory Service Manual CENTER CONSOLE AREA ANTENNA (REAR)DLK-61
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Check continuity between Intelligent Key unit harness connector (A) INFINITI QX56 2010 Factory Service Manual CENTER CONSOLE AREA ANTENNA (REAR)DLK-61
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Check continuity between Intelligent Key unit harness connector (A)](/manual-img/42/57032/w960_57032-894.png)
CENTER CONSOLE AREA ANTENNA (REAR)DLK-61
< COMPONENT DIAGNOSIS > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
3. Check continuity between Intelligent Key unit harness connector (A) M70 terminals 15, 16 and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness between Intelligent Key unit and center console area antenna (rear).
3.CHECK INSIDE KEY ANTENNA POWER SUPPLY SINGAL
1. Replace center console area antenna (rear). (New antenna or other antenna)
2. Connect Intelligent Key unit connector.
3. Check signal between Intelligent Key unit connector and ground with oscilloscope.
Is the inspection result normal?
YES >> Replace center console area antenna (rear).
NO >> Replace Intelligent Key unit. Refer to SEC-120, "
Removal and Installation".
Intelligent Key
unit connectorTe r m i n a l sCenter console area
antenna (rear) con-
nector Terminals Continuity
A: M70 15
B: M209 1
Ye s
16 2
Item Connector TerminalsContinuity
Intelligent Key unit A: M70 15
Ground No
16
ALKIA0586ZZ
Connector Item Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 15 Ground Ignition
switch is
pushed.
ALKIA0585ZZ
PIIB7441E
Revision: April 20092010 QX56
Page 896 of 4210
![INFINITI QX56 2010 Factory Service Manual DLK-62
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
LUGGAGE AREA ANTENNA
LUGGAGE AREA ANTENNA
DescriptionINFOID:0000000005146914
Detects whether Intelligent Key is inside the vehicle.
Componen INFINITI QX56 2010 Factory Service Manual DLK-62
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
LUGGAGE AREA ANTENNA
LUGGAGE AREA ANTENNA
DescriptionINFOID:0000000005146914
Detects whether Intelligent Key is inside the vehicle.
Componen](/manual-img/42/57032/w960_57032-895.png)
DLK-62
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
LUGGAGE AREA ANTENNA
LUGGAGE AREA ANTENNA
DescriptionINFOID:0000000005146914
Detects whether Intelligent Key is inside the vehicle.
Component Function CheckINFOID:0000000005146915
1.CHECK INSIDE KEY ANTENNA INPUT SIGNAL
With CONSULT-III
1. Check “ANTENNA” in “Active Test” mode with CONSULT-III.
2. Touch “ROOM ANT1”.
3. When Intelligent Key is in luggage area antenna detection area, hazard lamps flash.
Is the inspection result normal?
YES >> Luggage area antenna is OK.
NO >> Refer to DLK-62, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000005146916
Regarding Wiring Diagram information, refer to DLK-178, "Wiring Diagram — INTELLIGENT KEY SYSTEM —
".
1.CHECK INSIDE KEY ANTENNA POWER SUPPLY SIGNAL
1. Turn ignition switch OFF.
2. Check signal between Intelligent Key unit connector and ground with an oscilloscope.
Is the inspection result normal?
YES >> Luggage area antenna is OK.
NO >> GO TO 2
2.CHECK INSIDE KEY ANTENNA
1. Disconnect Intelligent Key unit connector and luggage area antenna connectors.
2. Check continuity between Intelligent Key unit harness connector (A) M70 terminals 35, 36 and luggage
area antenna harness connector (B) B76 terminals 1, 2.
Test Item Condition Possible cause
ROOM ANT1 An excessive high or low voltage from inside
antenna is sent to the Intelligent Key Unit • Luggage area antenna
• Between Intelligent Key unit and luggage area antenna
Connector Item
Te r m i n a l s
Condition Signal (V)
(Reference value)
(+) (–)
M70 Intelligent
Key unit 35 Ground Ignition
switch is
pushed.
ALKIA0587ZZPIIB7441E
Revision: April 20092010 QX56