Page 393 of 4083
![INFINITI QX56 2008 Factory Service Manual BCS-28
< FUNCTION DIAGNOSIS >[BCM]
DIAGNOSIS SYSTEM (BCM)
ERASE SELF-DIAGNOSIS
With CONSULT-III
1. Perform applicable inspection of malfunctioning item and then repair or replace.
2. Turn ignition sw INFINITI QX56 2008 Factory Service Manual BCS-28
< FUNCTION DIAGNOSIS >[BCM]
DIAGNOSIS SYSTEM (BCM)
ERASE SELF-DIAGNOSIS
With CONSULT-III
1. Perform applicable inspection of malfunctioning item and then repair or replace.
2. Turn ignition sw](/manual-img/42/57030/w960_57030-392.png)
BCS-28
< FUNCTION DIAGNOSIS >[BCM]
DIAGNOSIS SYSTEM (BCM)
ERASE SELF-DIAGNOSIS
With CONSULT-III
1. Perform applicable inspection of malfunctioning item and then repair or replace.
2. Turn ignition switch “ON” and select “SELF-DIAG
RESULTS” mode for “AIR PRESSURE MONITOR” with
CONSULTIII.
3. Touch “ERASE” on CONSULT-III screen to erase memory.
Without CONSULT-III
• In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned “ON” and“OFF”.
• However, this information is erased by turning igniti on switch “OFF” after performing self-diagnostic or by
erasing the memory using the CONSULT-III.
AIR PRESSURE MONITOR : CONSULT-III FunctionINFOID:0000000001696431
WORK SUPPORT MODE
31 Transmitter ch
ecksum error
(Front LH) Checksum data from front LH transmitter is malfunctioning.
WT-32
32Transmitter ch
ecksum error
(Front RH) Checksum data from front RH transmitter is malfunctioning.
33 Transmitter ch
ecksum error
(Rear RH) Checksum data from rear RH transmitter is malfunctioning.
34 Transmitter ch
ecksum error
(Rear LH) Checksum data from rear RH transmitter is malfunctioning.
35 Transmitter pressure data error
(Front LH) Air pressure data from front LH transmitter is malfunction.
WT-32
36Transmitter pressure data error
(Front RH) Air pressure data from front RH transmitter is malfunction.
37 Transmitter pressure data error
(Rear RH)
Air pressure data from rear RH transmitter is malfunction.
38 Transmitter pressure data error
(Rear LH) Air pressure data from rear LH transmitter is malfunction.
41 Transmitter function code error
(Front LH) Function code data from front LH transmitter is malfunction.
WT-32
42Transmitter function code error
(Front RH)
Function code data from front RH transmitter is malfunction.
43 Transmitter function code error
(Rear RH) Function code data from rear RH transmitter is malfunction.
44 Transmitter function code error
(Rear LH) Function code data from rear LH transmitter is malfunction.
45 Transmitter battery voltage low
(Front LH)
Battery voltage of front LH transmitter drops.
WT-32
46Transmitter battery voltage low
(Front RH) Battery voltage of front RH transmitter drops.
47 Transmitter battery voltage low
(Rear RH) Battery voltage of rear RH transmitter drops.
48 Transmitter battery voltage low
(Rear LH)
Battery voltage of rear LH transmitter drops.
52 Vehicle speed signal error Speed signal is not detected. WT-32
No flicker-
ing Tire pressure warning check
switch
Tire pressure warning sw
itch circuit is open. –
Flickering
pattern Items
Diagnostic items detected when··· Check item
Revision: March 2010 2008 QX56
Page 394 of 4083
![INFINITI QX56 2008 Factory Service Manual BCS
DIAGNOSIS SYSTEM (BCM)BCS-29
< FUNCTION DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
ID Read
The registered ID number is displayed.
ID Regist
Refer to
WT-6, "ID Registration Procedure".
SELF-D INFINITI QX56 2008 Factory Service Manual BCS
DIAGNOSIS SYSTEM (BCM)BCS-29
< FUNCTION DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
ID Read
The registered ID number is displayed.
ID Regist
Refer to
WT-6, "ID Registration Procedure".
SELF-D](/manual-img/42/57030/w960_57030-393.png)
BCS
DIAGNOSIS SYSTEM (BCM)BCS-29
< FUNCTION DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
ID Read
The registered ID number is displayed.
ID Regist
Refer to
WT-6, "ID Registration Procedure".
SELF-DIAG RESULTS MODE
Operation Procedure
Refer to WT-31, "Self-Diagnosis (With CONSULT-III)".
DATA MONITOR MODE
Screen of data monitor mode is displayed. Refer to WT-11, "CONSULT-III Function (BCM)".
NOTE:
When malfunction is detected, CONSULT-III perform REAL-TIME DIAGNOSIS.
Also, any malfunction detected while in this mode will be displayed at real time.
ACTIVE TEST MODE
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or else the actual malfunction may be different
from that displayed on CONSULT-III.
TEST ITEM LIST
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT ALM)INFOID:0000000001696432
WORK SUPPORT
Test item Content
WARNING LAMP This test is able to check to make sure that the warning lamp turns on.
ID REGIST WARNING This test is able to check to make sure that the buzzer sounds or the warning lamp turns on.
FLASHER This test is able to check to make sure that each turn signal lamp turns on.
HORN This test is able to check to make sure that the horn sounds.
Work Item Description
SECURITY ALARM SET Vehicle security function mode can be changed in this mode.
• ON: Vehicle security function is ON.
• OFF: Vehicle security function is OFF.
Revision: March 2010
2008 QX56
Page 395 of 4083
![INFINITI QX56 2008 Factory Service Manual BCS-30
< COMPONENT DIAGNOSIS >[BCM]
U1000 CAN COMM CIRCUIT
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000001696433
Refer to
LAN-44, "CAN Communication Signal Chart".
DTC LogicIN INFINITI QX56 2008 Factory Service Manual BCS-30
< COMPONENT DIAGNOSIS >[BCM]
U1000 CAN COMM CIRCUIT
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000001696433
Refer to
LAN-44, "CAN Communication Signal Chart".
DTC LogicIN](/manual-img/42/57030/w960_57030-394.png)
BCS-30
< COMPONENT DIAGNOSIS >[BCM]
U1000 CAN COMM CIRCUIT
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000001696433
Refer to
LAN-44, "CAN Communication Signal Chart".
DTC LogicINFOID:0000000001696434
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000001696435
1. PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 seconds or more.
2. Check “Self Diagnostic Result” of BCM.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Refer to LAN-14, "Trouble Diagnosis Flow Chart".
NO >> Refer to GI-38, "
Intermittent Incident".
DTCCONSULT-III display
description DTC Detection Condition
Possible cause
U1000 CAN COMM CIRCUIT When BCM cannot communicate CAN com-
munication signal continuously for 2 sec-
onds or more. Any item (or items) of the following listed below is
malfunctioning in CAN communication system.
•Transmission
• Receiving (ECM)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (MULTI AV)
• Receiving (IPDM E/R)
• Receiving (I-KEY)
Revision: March 2010
2008 QX56
Page 396 of 4083
BCS
U1010 CONTROL UNIT (CAN)BCS-31
< COMPONENT DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
U1010 CONTROL UNIT (CAN)
DTC LogicINFOID:0000000001696436
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000001696437
1. REPLACE BCM
When “DTC:U1010” is detected, replace BCM.
>> Replace BCM. Refer to BCS-55, "
Removal and Installation".
Special Repair RequirementINFOID:0000000001696438
1. ADDITIONAL SERVICE WHEN REPLACING BCM
>> Refer to BCS-3, "
ADDITIONAL SERVICE WHEN REPLAC ING CONTROL UNIT : Special Repair
Requirement".
DTCCONSULT-III display de-
scription DTC Detection Condit
ion Possible cause
U1010 CONTROL UNIT (CAN) When detecting error during the initial diagnosis of CAN control-
ler of BCM.
BCM
Revision: March 2010
2008 QX56
Page 397 of 4083
![INFINITI QX56 2008 Factory Service Manual BCS-32
< COMPONENT DIAGNOSIS >[BCM]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis ProcedureINFOID:0000000001696439
1. CHECK FUSES AND FUSIBLE LINK
Check that the following INFINITI QX56 2008 Factory Service Manual BCS-32
< COMPONENT DIAGNOSIS >[BCM]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis ProcedureINFOID:0000000001696439
1. CHECK FUSES AND FUSIBLE LINK
Check that the following](/manual-img/42/57030/w960_57030-396.png)
BCS-32
< COMPONENT DIAGNOSIS >[BCM]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis ProcedureINFOID:0000000001696439
1. CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not blown.
Is the fuse blown?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit.
NO >> GO TO 2
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check voltage between BCM harness connector and ground.
Is the measurement value normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES >> INSPECTION END
NO >> Repair or replace harness.
Terminal No. Signal nameFuses and fusible link No.
57 Battery power supply 22 (15A)
70 F (50A)
11 Ignition ACC or ON 4 (10A)
38 Ignition ON or START 59 (10A)
ConnectorTe r m i n a l s
Power
source Condition Voltage (V) (Ap-
prox.)
(+) (-)
M18 11 Ground
ACC
power
supply Ignition
switch
ACC or
ON Battery voltage
38 Ground Ignition
power
supply Ignition
switch ON or START Battery voltage
M20 57 Ground
Battery
power
supply Ignition
switch OFF Battery voltage
70 Ground Battery
power
supply Ignition
switch
OFF Battery voltage
LIIA2415E
BCM
GroundContinuity
Connector Terminal
M20 67 Yes
LIIA0915E
Revision: March 2010 2008 QX56
Page 398 of 4083
![INFINITI QX56 2008 Factory Service Manual BCS
COMBINATION SWITCH INPUT CIRCUITBCS-33
< COMPONENT DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
COMBINATION SWITCH
INPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000001696440
1. CHECK INPUT 1 - 5 INFINITI QX56 2008 Factory Service Manual BCS
COMBINATION SWITCH INPUT CIRCUITBCS-33
< COMPONENT DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
COMBINATION SWITCH
INPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000001696440
1. CHECK INPUT 1 - 5](/manual-img/42/57030/w960_57030-397.png)
BCS
COMBINATION SWITCH INPUT CIRCUITBCS-33
< COMPONENT DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
COMBINATION SWITCH
INPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000001696440
1. CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM and combination switch.
3. Check continuity between BCM harness connector and combi- nation switch harness connector.
Does continuity exist?
YES >> GO TO 2
NO >> Repair or replace harness.
2. CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT
Check for continuity between BCM harness connector and ground.
Does continuity exist?
YES >> Repair or replace harness.
NO >> GO TO 3
3. CHECK BCM OUTPUT VOLTAGE
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM harness connector and ground.
Is the measurement value normal?
System BCM
Combination switch
Continuity
Connector Terminal Connector Terminal
INPUT 1
M18(A) 6
M28(B) 6
Ye s
INPUT 2
57
INPUT 3 410
INPUT 4 39
INPUT 5 28
ALMIA0275ZZ
SystemBCM
GroundContinuity
Connector Terminal
INPUT 1
M186
No
INPUT 2
5
INPUT 3 4
INPUT 4 3
INPUT 5 2
ALMIA0276ZZ
SystemTe r m i n a l s
Voltag e
(Approx.)
(+)
(− )
BCM
Ground
Connector Terminal
INPUT 1
M186
Refer to BCS-
38, "Refer-
ence Value".
INPUT 2
5
INPUT 3 4
INPUT 4 3
INPUT 5 2
ALMIA0277ZZ
Revision: March 2010 2008 QX56
Page 399 of 4083
BCS-34
< COMPONENT DIAGNOSIS >[BCM]
COMBINATION SWITCH INPUT CIRCUIT
YES >> GO TO 4
NO >> Replace BCM. Refer to
BCS-55, "
Removal and Installation".
4. CHECK COMBINATION SWITCH
Check combination switch. Refer to BCS-36, "
Description".
Is the check result normal?
YES >> Replace BCM. Refer to BCS-55, "Removal and Installation".
NO >> Replace the combination switch (applicable parts). Refer to EXL-119, "
Removal and Installation".
Special Repair RequirementINFOID:0000000001696441
1. ADDITIONAL SERVICE WHEN REPLACING BCM
>> Refer to BCS-3, "
ADDITIONAL SERVICE WHEN REPLAC ING CONTROL UNIT : Special Repair
Requirement".
Revision: March 2010 2008 QX56
Page 400 of 4083
![INFINITI QX56 2008 Factory Service Manual BCS
COMBINATION SWITCH OUTPUT CIRCUITBCS-35
< COMPONENT DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
COMBINATION SWITCH
OUTPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000001696442
1. CHECK OUTPUT 1 INFINITI QX56 2008 Factory Service Manual BCS
COMBINATION SWITCH OUTPUT CIRCUITBCS-35
< COMPONENT DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
COMBINATION SWITCH
OUTPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000001696442
1. CHECK OUTPUT 1](/manual-img/42/57030/w960_57030-399.png)
BCS
COMBINATION SWITCH OUTPUT CIRCUITBCS-35
< COMPONENT DIAGNOSIS > [BCM]
C
D
E
F
G H
I
J
K L
B A
O P
N
COMBINATION SWITCH
OUTPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000001696442
1. CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM and combination switch.
3. Check continuity between BCM harness connector and combi- nation switch harness connector.
Does continuity exist?
YES >> GO TO 2
NO >> Repair or replace harness.
2. CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT
Check for continuity between BCM harness connector and ground.
Does continuity exist?
YES >> Repair or replace harness.
NO >> GO TO 3
3. CHECK COMBINATION SWITCH
Check combination switch. Refer to BCS-36, "
Description".
Is the check result normal?
YES >> Replace BCM. Refer to BCS-55, "Removal and Installation".
NO >> Replace combination switch (applicable parts). Refer to EXL-119, "
Removal and Installation".
Special Repair RequirementINFOID:0000000001696443
1. ADDITIONAL SERVICE WHEN REPLACING BCM
>> Refer to BCS-3, "
ADDITIONAL SERVICE WHEN REPLAC ING CONTROL UNIT : Special Repair
Requirement".
SystemBCM
Combination switch
Continuity
Connector Terminal Connector Terminal
OUTPUT 1
M18(A) 36
M28(B) 1
Ye s
OUTPUT 2
352
OUTPUT 3 343
OUTPUT 4 334
OUTPUT 5 325
ALMIA0278ZZ
SystemBCM
GroundContinuity
Connector Terminal
OUTPUT 1
M1836
No
OUTPUT 2
35
OUTPUT 3 34
OUTPUT 4 33
OUTPUT 5 32
ALMIA0279ZZ
Revision: March 2010 2008 QX56