1991 MITSUBISHI MONTERO Service Manual

park assist remote start CD changer spare tire location airbag off change language

Page 177 of 1333

MITSUBISHI MONTERO 1991 Service Manual Replacement of the rotor is required because it does not meet
design specifications.
Some conditions indicate that a service or part replacement
is suggested because the par

Replacement of the rotor is required because it does not meet
design specifications.
Some conditions indicate that a service or part replacement
is suggested because the part is close to the end of its useful life
or addresses a customer's need, convenience or request. If a
customer's vehicle has one of these conditions, the procedure may be
only to suggest service.
Example:
An exhaust pipe is rusted, corroded or weak, but no leaks are
present. In this case, the exhaust pipe has not failed.
However, there is evidence that the pipe may need replacement
in the near future. Replacement of the pipe may be suggested
for the customer's convenience in avoiding a future problem.
Example:
The customer desires improved ride and/or handling, but the
vehicle's shocks or struts have not failed. In this case,
replacement may be suggested to satisfy the customer's
wishes. In this case, replacement of the shocks or struts may
not be sold as a requirement.
A customer, of course, has the choice of whether or not a
shop will service his or her vehicle. He or she may decide not to
follow some of your suggestions. When a repair is required, a MAP
shop must refuse partial service on that system if, in the judgment of
the service provider, proceeding with the work could create or
continue an unsafe condition. When a procedure states that required
or suggested repair or replacement is recommended, the customer must
be informed of the generally acceptable repair/replacement options
whether or not performed by the shop.
When presenting suggested repairs to the customer, you must
present the facts, allowing the customer to draw their own conclusions
and make an informed decision about how to proceed.
The following reasons may be used for required and suggested
services. These codes are shown in the "Code" column of the MAP
Uniform Inspection & Communications Standards that follow:
Reasons to Require Repair or Replacement
A - Part no longer performs intended purpose
B - Part does not meet a design specification (regardless of
performance)
C - Part is missing
NOTE: When a repair is required, the shop must refuse partial
service to the system in question, if the repair creates
or continues an unsafe condition.
Reasons to Suggest Repair or Replacement
1 - Part is close to the end of its useful life (just above
discard specifications, or weak; failure likely to occur
soon, etc.)
2 - To address a customer need, convenience, or request (to
stiffen ride, enhance performance, eliminate noise, etc.)
3 - To comply with maintenance recommended by the vehicle's
Original Equipment Manufacturer (OEM)
4 - Technician's recommendation based on substantial and
informed experience
NOTE: Suggested services are always optional. When presenting
suggested repairs to the customer, you must present the
facts, allowing the customer to draw their own conclusions

Page 178 of 1333

MITSUBISHI MONTERO 1991 Service Manual and make an informed decision about how to proceed.
BRAKES
SERVICE PROCEDURES REQUIRED & SUGGESTED FOR PROPER
VEHICLE OPERATION
Some states may have speci

and make an informed decision about how to proceed.
BRAKES
SERVICE PROCEDURES REQUIRED & SUGGESTED FOR PROPER
VEHICLE OPERATION
Some states may have specifications that differ from OEM.
Check your local/state regulations. Where state or local laws are
stricter, they take precedence over these guidelines.
ACCELEROMETERS (G SENSOR OR LATERAL)
ACCELEROMETER INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Broken .................. A ............ Require replacement.
Connector loose ......... A .. Require repair or replacement.
Loose ................... B .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Out of position ......... B ....... Require re-positioning to
vehicle manufacturer's
specifications.
Output signal incorrect . B ............ Require replacement.
\
\
\
\
\
\
\

ACCUMULATORS
ACCUMULATOR INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Leaking ................. B ............ Require replacement.
Missing ................. C ............ Require replacement.
Pre-charge incorrect .... B ............ Require replacement.
\
\
\
\
\
\
\

ANCHOR PINS
See BACKING PLATES .
ANTI-LOCK BRAKE SYSTEMS
NOTE: Anti-lock brakes are an integral part of the brake system. It
is essential that the anti-lock brakes function properly when
brake service is performed.
Anti-lock brake systems are commonly referred to as "ABS" and
will be referred to as "ABS" throughout these guidelines. Some ABS
components also function as part of a traction control system (TCS).
WARNING: When diagnosing and servicing high pressure components,
observe safety procedures and equipment requirements
established by the vehicle manufacturer to reduce the
possibility of serious personal injury.
NOTE: Intermittent electrical conditions are often caused by a loss
of ground, poor connection, or water intrusion into the
wiring harness.

Page 179 of 1333

MITSUBISHI MONTERO 1991 Service Manual NOTE: Electro-magnetic interference (EMI) may be caused by
incorrect installation of accessories or components. EMI can
result in improper system operation.
BACKING PLATE

NOTE: Electro-magnetic interference (EMI) may be caused by
incorrect installation of accessories or components. EMI can
result in improper system operation.
BACKING PLATES
BACKING PLATE INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Anchor pin bent ......... B .. Require repair or replacement.
Anchor pin broken ....... A ............ Require replacement.
Anchor pin worn, affecting
structural integrity ... B ............ Require replacement.
Backing plate bent ...... B .. Require repair or replacement.
Backing plate broken .... A ............ Require replacement.
Backing plate cracked ... B .. Require repair or replacement.
Corroded, affecting
structural integrity .... A ............ Require replacement.
Loose ................... B .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Shoe lands worn ......... A .. Require repair or replacement.
\
\
\
\
\
\
\

BRAKE FLUID
CAUTION: Most manufacturers prohibit the use of DOT 5 brake fluid
in a system equipped with ABS.
DOT 3, DOT 4, and DOT 5.1 brake fluids are clear or light
amber in color. DOT 5 brake fluid is violet in color. Correct fluid
required for the brake system is stamped on the master cylinder cover.
BRAKE FLUID INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Beyond service interval . 3 .. Suggest flushing and refilling
with correct fluid.
Brake fluid type
incorrect .............. B .. Require flushing and refilling
with correct fluid.
Contaminated, for example,
fluid other than brake
fluid present .......... A or B ....... ( 1) Require service.
Hydraulic component ..... 3 .. Suggest flushing and refilling
overhaul or replacement with correct fluid.
Rubber master cylinder
cover gasket distorted
and gummy .............. A .......... ( 2) Require replacement
of gasket.
( 1) - If a fluid other than brake fluid is present in the brake
system which DOES affect the rubber parts, the required
service is to:
* Remove all components having rubber parts from the
system.
* Flush lines with denatured alcohol or brake cleaner
* Repair or replace all components having rubber parts
* Flush and fill with correct brake fluid. (Code A)
If a fluid other than brake fluid is present in the brake

Page 180 of 1333

MITSUBISHI MONTERO 1991 Service Manual system which DOES NOT affect the rubber parts, the required
service is to flush and fill with the correct brake fluid.
(Code B)
( 2) - This condition may indicate contaminated brake

system which DOES NOT affect the rubber parts, the required
service is to flush and fill with the correct brake fluid.
(Code B)
( 2) - This condition may indicate contaminated brake fluid.
\
\
\
\
\
\
\

BRAKE FRICTION MATERIAL
See FRICTION MATERIAL .
BRAKE PADS
See FRICTION MATERIAL .
BRAKE PEDALS
BRAKE PEDAL INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Bent, affecting
performance ............ A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Pedal pad missing ....... C .... Require replacement of pedal
pad.
Pedal pad worn .......... 1 ............ Suggest replacement.
Pivot bushings worn,
affecting performance .. A .... Require replacement of pivot
bushings.
\
\
\
\
\
\
\

BRAKE SHOES
See FRICTION MATERIAL .
BRAKE SHOE HARDWARE
See also SELF-ADJUSTING SYSTEMS .
BRAKE SHOE HARDWARE INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Broken .................. A ............ Require replacement.
Distorted ............... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Surfaces rust-pitted .... 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\

BRAKE STOPLIGHT SWITCHES
BRAKE STOPLIGHT INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.

Page 181 of 1333

MITSUBISHI MONTERO 1991 Service Manual Connector melted ........ A ........ (1) Require replacement.
Connector missing ....... C ............ Require replacement.
Missing ................. C ............ Require replacement.
Ou

Connector melted ........ A ........ (1) Require replacement.
Connector missing ....... C ............ Require replacement.
Missing ................. C ............ Require replacement.
Out of adjustment ....... B ........... Require adjustment or
replacement.
Output signal incorrect . B ............ Require replacement.
Terminal burned, affecting
performance ............ A .............. ( 2) Require repair
or replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance ... A .. Require repair or replacement.
Terminal corroded, not
affecting performance ... 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance ... 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Determine cause and correct prior to replacement of part.
( 2) - Determine cause and correct prior to repair or replacement
of part.
\
\
\
\
\
\
\

BULB SOCKETS
BULB SOCKET INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Broken .................. A .. Require repair or replacement.
Bulb seized in socket ... A .. Require repair or replacement.
Burned, affecting
performance ............ A .............. ( 1) Require repair
or replacement.
Burned, not affecting
performance ............ 2 .............. ( 1) Suggest repair
or replacement.
Connector broken ........ A .. Require repair or replacement.
Connector missing ....... C ............ Require replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A .............. ( 2) Require repair
or replacement.
Corroded, affecting
performance ............ A .. Require repair or replacement.
Corroded, not affecting
performance ............ 2 .. Suggest repair or replacement.
Leaking ................. A .. Require repair or replacement.
Melted .................. A ........ ( 2) Require replacement.

Page 182 of 1333

MITSUBISHI MONTERO 1991 Service Manual Shorted ................. A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ..........

Shorted ................. A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A .............. (2) Require repair
or replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of socket.
( 2) - Determine cause and correct prior to repair or
replacement of part.
\
\
\
\
\
\
\

BULBS AND LEDS
NOTE: Copied from Electrical UIGs and modified. Does not
include soldered-in components.
BULB AND LED INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Application incorrect ... B ........ ( 1) Require replacement.
Base burned, affecting
performance ............ A .............. ( 2) Require repair
or replacement.
Base burned, not affecting
performance ............ 2 .............. ( 2) Suggest repair
or replacement.
Base corroded, affecting
performance ............ A .. Require repair or replacement.
Base corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Base loose, affecting
performance ............ B .. Require repair or replacement.
Base loose, not affecting
performance ............ 1 .. Suggest repair or replacement.
Burned out .............. A ............ Require replacement.
Intermittent ............ A ............ Require replacement.
Missing ................. C ............ Require replacement.
Seized in socket ........ A .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A .............. ( 2) Require repair
or replacement.
Terminal burned, not
affecting performance .. 2 .............. ( 2) Suggest repair
or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.

Page 183 of 1333

MITSUBISHI MONTERO 1991 Service Manual Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
(1) - Application incorrect includes wrong bulb coating
or color.
( 2) - Determine cause and correct prior t

Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
(1) - Application incorrect includes wrong bulb coating
or color.
( 2) - Determine cause and correct prior to repair or
replacement of part.
\
\
\
\
\
\
\

CALIPER HARDWARE
CALIPER HARDWARE INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Bent ................... A .. Require repair or replacement.
Broken .................. A .. Require repair or replacement.
Corroded, affecting
performance ............ A .. Require repair or replacement.
Dust boots on slider pin
(bolt) missing ......... C ... Require replacement of boots.
Dust boots on slider pin
(bolt) torn ............ A ... Require replacement of boots.
Missing ................. C ............ Require replacement.
Shim bent ............... A ............. ( 1) Require removal
or replacement.
Shim (OE standard)
missing ................ C ........ ( 2) Require replacement.
Shim out of position .... B ............. ( 1) Require removal
or replacement.
Shim worn ............... A ............. ( 1) Require removal
or replacement.
Slider pin (bolt) bent .. B ... Require replacement of slider
pin or bolt and lubricants.
Slider pin (bolt)
rust-pitted ............ A ... Require replacement of slider
pin or bolt and lubricants.
Slider pin (bolt) worn .. A ... Require replacement of slider
pin or bolt and lubricants.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Worn, affecting
performance ............ A ............ Require replacement.
( 1) - Removal is acceptable if shim is not OE.
( 2) - Aftermarket shims may be suggested to reduce noise.
\
\
\
\
\
\
\

CALIPERS
You are not required to replace or rebuild calipers in axle
sets. However, when replacing or rebuilding a caliper due to the
conditions that follow, you may suggest servicing, rebuilding, or
replacement of the other caliper (on the same axle) for improved
performance and preventive maintenance (for example, the part is close
to the end of its useful life, replacing the caliper may extend pad
life, or contribute to more balanced braking).
CAUTION: When installing loaded calipers, it is required that
friction material be matched in axle sets for consistent
braking characteristics.

Page 184 of 1333

$MITSUBISHI MONTERO 1991 Service Manual CALIPER INSPECTION��\ ��\ ��\ ��\ ��\ ��\ ��\ �� Condition Code$

CALIPER INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Bleeder port damaged .... A ... Require repair or replacement
of caliper.
Bleeder screw broken off
in caliper ............. A ........... (1) Require repair or
replacement of caliper.
Bleeder screw plugged ... A ........... ( 1) Require repair or
replacement of bleeder screw.
Bleeder screw seized .... A ......... ( 2) Require replacement
of caliper.
Casting corroded,
affecting structural
integrity .............. A ............ Require replacement.
Casting damaged, affecting
structural integrity ... A ............ Require replacement.
Dust boot around caliper
torn ................... A ..... Require replacement of dust
boot.
Leaking ................. A .. Require repair or replacement.
Mounting pin threads
damaged ................ A ... Require repair or replacement
of component with damaged
threads.
Mounting pin threads
stripped in caliper
bracket (threads
missing) ............... A ... Require repair or replacement
of caliper bracket.
Mounting pin threads
stripped in steering
knuckle (threads
missing) ............... A ... Require repair or replacement
of steering knuckle.
Mounting pin threads
stripped (threads
missing) ............... A ... Require repair or replacement
of component with stripped
threads.
Parking brake cable
support, lever, or return
spring bent ............ A ... Require replacement of parts.
Parking brake cable
support, lever, or return
spring broken .......... A ... Require replacement of parts.
Parking brake mechanism in
caliper inoperative .... A .. Require repair or replacement.
Piston corroded (pitted
or peeling chrome
plating) ............... B ... Require replacement of piston
and rebuilding or replacement
of caliper.
Piston damaged, affecting
performance ............ B ... Require replacement of piston
and rebuilding or replacement
of caliper.
Piston damaged, not
affecting performance .. .. ........ No service suggested or
required.
Piston finish worn off .. B ... Require replacement of piston
and rebuilding or replacement

Load next 8 pages

Page: < prev 1-10 ... 145-152 153-160 161-168 169-176 177-184 185-192 193-200 201-208 209-216 ... 1336 next >

cooling fuel type spare tire CD changer headlight bulb inflation pressure