1996 TOYOTA LAND CRUISER Workshop Manual

−
DIAGNOSTICS CRUISE CONTROL SYSTEM
DI−335
1996 LAND CRUISER (RM451U)
2 Check harness and connector between cruise control ECU and DLC1, DLC1 and
body ground (See page IN−28).
NG Repair or replace harness or connector.
OK
Check and replace cruise control ECU
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−336
−
DIAGNOSTICS CRUISE CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
Actuator Control Cable
INSPECTION PROCEDURE
1 Actuator control cable inspection
CHECK:
(a) Check that the actuator, control cable throttle link are properly installed and that the cable and link are
connected correctly.
(b) Check that the actuator and bell crank are operating smoothly.
(c) Check that the cable is not loose or too tight.
OK:
Freeplay: less than 10 mm
HINT:
If the control cable is very loose, the vehicle’s loss of speed going uphill will be large.
If the control cable is too tight, the idle RPM will become high.
DI5OR−01
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EC07H−06
−
EMISSION CONTROL EMISSION CONTROL SYSTEM
EC−1
614
Author: Date:
1996 LAND CRUISER (RM451U)
EMISSION CONTROL SYSTEM
PURPOSE
The emission control systems are installed to reduce the amount of HC, CO a\
nd NOx exhausted from the
engine ((3), (4) and (5)), to prevent the atmospheric release of blow −by gas− containing HC (1) and evapo-
rated fuel containing HC being released from the fuel tank (2).
The function of each system is shown in the following table.
SystemAbbreviationFunction
(1) Positive Crankcase V entilation
(2) Evaporative Emission Control
(3) Exhaust Gas Recirculation
(4) Three− Way Catalytic Converter
(5) Sequential Multiport Fuel Injection*PCV
EVAP EGR
TWC SFIReduces HC
Reduces evaporated HC
Reduces NOx
Reduces HC, CO and NOx
Injects a precisely timed, optimum amount of fuel for reduced
exhaust emissions
Remark: * For inspection and repair of the SFI system, refer to the SF section \
in this manual.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EC07I−06
EC−2
−
EMISSION CONTROL PARTS LAYOUT AND SCHEMATIC DRAWING
615
Author: Date:
1996 LAND CRUISER (RM451U)
PARTS LAYOUT AND SCHEMATIC DRAWING
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EC07J−05
−
EMISSION CONTROL PARTS LAYOUT AND SCHEMATIC DRAWING
EC−3
1996 LAND CRUISER (RM451U)
DRAWING
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EC0G9−01
EC−4−
EMISSION CONTROL POSITIVE CRANKCASE VENTILATION (PCV)
SYSTEM
617
Author: Date:
1996 LAND CRUISER (RM451U)
POSITIVE CRANKCASE
VENTILATION (PCV) SYSTEM
INSPECTION
1. REMOVE PCV VALVE
(a) Disconnect the PCV hose from the PCV valve.
(b) Remove the PCV valve.
2. INSTALL CLEAN HOSE TO PCV VALVE
3. INSPECT PCV VALVE OPERATION
(a) Blow air into the cylinder head side, and check that air
passes through easily.
CAUTION:
Do not suck air through the valve.
Petroleum substances inside the valve are harmful.
(b) Blow air into the air intake chamber side, and check that air passes through with difficulty.
If operation is not as specified, replace the PCV valve.
4. REMOVE CLEAN HOSE FROM PCV VALVE
5. REINSTALL PCV VALVE
6. VISUALLY INSPECT HOSE, CONNECTIONS AND GASKETS
Check for cracks, leaks or damage.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EC0GA−01
−
EMISSION CONTROL EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM
EC−5
618
Author: Date:
1996 LAND CRUISER (RM451U)
EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EC0GB−01
EC3069
Gasket
Check Valve (V acuum Valve)
EC−6
−
EMISSION CONTROL EVAPORATIVE EMISSION (EVAP) CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. VISUALLY INSPECT LINES AND CONNECTIONS
Look for loose connections, sharp bends or damage.
2. VISUALLY INSPECT FUEL TANK
Look for deformation, cracks or fuel leakage.
3. VISUALLY INSPECT FUEL TANK CAP
Check if the cap and/or gasket are deformed or damaged.
If necessary, repair or replace the cap.
4. INSPECT TVV OPERATION WITH COLD ENGINE
(a) The engine coolant temperature should be below 45 °C
(113 °F).
(b) Disconnect the EVAP hose from the union pipe.
(c) Start the engine.
(d) Gradually increase the engine speed from idle to 3,000 rpm and check that air suction is not felt at the union pipe.
5. INSPECT OPERATION OF VCV WITH HOT ENGINE
(a) Warm up the engine.
(b) With the engine idling, check that air suction is not felt at union pipe.
(c) Gradually increase the engine speed to 3,000 rpm and check that there is air suction at the union pipe.
(d) Reconnect the EVAP hose to the union pipe.
If no problem is found with this inspection, system is normal;
otherwise inspect each part.
6. REMOVE CHARCOAL CANISTER WITH BRACKET
7. REMOVE CHARCOAL CANISTER FROM BRACKET
8. REMOVE CAP FROM CHARCOAL CANISTER
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010