1996 TOYOTA LAND CRUISER Workshop Manual

Q08225
Q08634
TOYOTA Hand−held Tester
DLC3
DI−132
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
The diagnosis system operates in normal mode
during normal vehicle use, and also has a check
mode for technicians to simulate malfunction symp-
toms and perform troubleshooting. Most DTCs use
2 trip detection logic(*) to prevent erroneous detec-
tion. By switching the ECM to check mode when
troubleshooting, the technician can cause the MIL
to light up for a malfunction that is only detected
once or momentarily (TOYOTA hand−held tester)
(See step 3).
*2 trip detection logic:
When a logic malfunction is first detected, the mal-
function is temporarily stored in the ECM memory.
If the same malfunction is detected again during the 2nd test
drive, this 2nd detection causes the MIL to light up.
2. Normal Mode: INSPECT DIAGNOSIS
(a) Check the MIL. (1) The MIL lights up when the ignition switch is turnedON and the engine is not running.
HINT:
If the MIL does not light up, troubleshoot the combination meter
(See page BE−2 ).
(2) When the engine is started, the MIL should go off.
If the lamp remains on, the diagnosis system has
detected a malfunction or abnormality in the sys-
tem.
(b) Check the DTC.
NOTICE:
TOYOTA hand−held tester only:
When the diagnostic system is switched from the normal
mode to the check mode, it erases all DTCs and freeze
frame data recorded in the normal mode. So before switch-
ing modes, always check the DTCs and freeze frame data,
and note them down. (1) Prepare the OBD II scan tool (complying with SAEJ1978) or TOYOTA hand−held tester.
(2) Connect the OBD II scan tool or TOYOTA hand−
held tester to the DLC3 in the fuse box at the lower
left of the instrument panel.
(3) Turn the ignition switch ON and turn the OBD II scan
tool or TOYOTA hand−held tester switch ON.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08634
TOYOTA Hand−held Tester
DLC3
FI3605
ON
OFF 0.13 sec.
Flashing
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−133
1996 LAND CRUISER (RM451U)
(4) Use the OBD II scan tool or TOYOTA hand−held
tester to check the DTCs and freeze frame data.
Note them down (For operating instructions, see
the OBD II scan tool’s instruction book).
(5) See page DI−143 to confirm the details of the
DTCs.
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand −held tester) to check the DTCs, use
the normal mode. For codes on the DTC chart subject to ”2
trip detection logic”, turn the ignition switch off after the
symptoms have been simulated for the 1st time. Them re-
peat the simulation process again. When the program has
been simulated twice, the MIL lights up and the DTCs are
recorded in the ECM.
3. Check Mode: INSPECT DIAGNOSIS
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has high sens-
ing ability to detect malfunctions. Furthermore, the same diag-
nostic items which are detected in the normal mode can also be
detected in check mode.
(a) Check the DTC. (1) Check the initial conditions.
Battery positive voltage 11 V or more.
Throttle valve fully closed.
Transmission in P position.
Air conditioning switched off.
(2) Turn the ignition switch OFF.
(3) Prepare the TOYOTA hand−held tester.
(4) Connect the TOYOTA hand− held tester to the
DLC3 in the fuse box at the lower left of the instru-
ment panel.
(5) Turn the ignition switch ON and switch the T OYOTA
hand −held tester ON.
(6) Switch the TOYOTA hand −held tester from the nor-
mal mode to the check mode (Check that the MIL
flashes).
(7) Start the engine (The MIL goes).
(8) Simulate the conditions of the malfunction de- scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTCs etc.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N09214
DLC3
DI−134
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
(9) After simulating the malfunction conditions, use the
TOYOTA hand−held tester diagnosis selector to
check the DTCs and freeze frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. T urning the ignition
switch off switches the diagnosis system from check mode to
normal mode, so all DTCs, etc. are erased. (10) After checking the DTC, inspect the applicable cir-cuit.
(b) Clear the DTC. The following actions will erase the DTCs and freeze
frame data.Operating the OBD II scan tool (complying with SAE
J1978) or TOYOTA hand−held tester to erase the
codes (See the OBD II scan tool’s instruction book
for operating instructions.).
NOTICE:
If the T OYOTA hand−held tester switches the ECM from the
normal mode to the check mode or vice−versa, or if the
ignition switch is turned from ON to ACC or OFF during the
check mode, the DTCs and freezed frame data will be
erased.
(c) Check the DLC3. The vehicle’s ECM uses V.P.W. (V ariable Pulse Width) for
communication to comply with SAE J1850. The terminal
arrangement of DLC3 complies with SAE J1962 and
matches the V.P.W. format.
Terminal No.Connection/V oltage or ResistanceCondition
2Bus  Line/Pulse generationDuring communication
4Chassis Ground − Body/1 Ω or lessAlways
5Signal Ground − Body/1 Ω or lessAlways
16Battery Positive − Body/9 − 14 V or 1 Ω or lessAlways
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−135
1996 LAND CRUISER (RM451U)
HINT:
If your display shows ”UNABLE TO CONNECT TO VEHICLE”
when you have connected the cable of the OBD II scan tool or
TOYOTA hand−held tester to the DLC3, turned the ignition
switch ON and operated the scan tool, there is a problem on the
vehicle side or tool side.
If communication is normal when the tool is connected to
another vehicle, inspect the DLC3 on the original vehicle.
If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool’s instruction manual.
4. CHECK FOR INTERMITTENT PROBLEMS
TOYOTA hand−held tester only:
By putting the vehicle’s ECM in the check mode, 1 trip detection logic is possible instead of 2\
trip detection
logic and sensitivity to detect open circuits is increased. This makes it easier t\
o detect intermittent problems.
(1) Clear the DTC (See step 3).
(2) Set the check mode (See step 3).
(3) Do a simulation test (See page IN−18).
(4) Check the cnnector connection and terminal (See page IN−28).
(5) Visual check and contact pressure (See page IN−28).
(6) Handle the connector (See page IN−28).
5. ROAD TEST
NOTICE:
Perform the test at normal operating ATF temperature 50 − 80°C (122 − 176° F).
(a) D position test in NORM and PWR pattern positions. Shift into the D position and hold the accelerator pedal constant at the full\
throttle valve opening posi-
tion and check the following:
HINT:
When the 2nd start switch in on, there is no 1 → 2 up−shift and 2 →1 down−shift.
(1) 1 →2, 2 → 3 and 3 → O/D up−shift takes place, and shift point should conform to those shown
in the automatic shift schedule. Conduct a test under both Normal and Powe\
r patterns.
HINT:
There is no O/D up−shift or lock−up when the coolant temperature is below 55 °C (131°F ).
Evaluation:
If there is no 1 → 2 up−shift:
Shift solenoid valve No. 2 is stuck.
1−2 shift valve is stuck.
If there is no 2 → 3 up−shift:
Shift solenoid valve No. 1 is stuck.
2−3 shift valve is stuck.
If there is no 3 → O/D up−shift:
3−4 shift valve is stuck.
If the shift point is defective:
Throttle valve, 1−2 shift valve, 2−3 shift valve, 3−4 shift valve etc., are defective.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−136
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
If the lock−up is defective:
Lock−up solenoid is stuck.
Lock−up control valve is stuck.
Lock−up signal value is stuck.
(2) In the same way, check the shock and slip at the 1 → 2, 2 →3 and 3 → O/D up−shift.
Evaluation:
If the shock is excessive:
Line pressure is too high.
Accumulator is defective.
Check ball is defective. (3) Run at the D position lock −up or O/D gear and check for abnormal noise and vibration.
HINT:
The check for the cause of abnormal noises and vibration must be made with \
extreme care as it could also
be due to loss of balance in the propeller shaft, differential, torque converter clutch, etc.
(4) While running in the D position, 2nd, 3rd and O/D gears, check to see that the\
possible kick −down
vehicle speed limits for 2 →1, 3 → 2 and O/D →3 kick−downs conform to those indicated on
the automatic shift schedule.
(5) Check for abnormal shock and slip at kick −down.
(6) Check for the lock −up mechanism.
Drive in D position, O/D gear, at a steady speed (lock −up ON) of about 95 km/h (59 mph).
Lightly depress the accelerator pedal and check that the engine RPM does not change
abruptly.
If there is a big jump in engine RPM, there is no lock −up.
(b) 2 position test. Shift into the 2 position and, while driving with the accelerator pedal held \
constantly at the full throttle
valve opening position, push in one of the pattern selectors and check the fo\
llowing points:
HINT:
When the 2nd start switch is on, there is no 1 → 2 up−shift and 2 →1 down−shift.
(1) Check to see that the 1 → 2 up− shift takes place and that the shift point conforms to the automatic
shift schedule.
HINT:
There is no O/D up−shift and lock−up in the 2 position. (2) While running in the 2 position and 2nd ge ar, release the accelerator pedal and check the engine
braking effect.
Evaluation:
If there is no engine braking effect:
2nd coast brake is defective. (3) Check for abnormal noise at acceleration and deceleration, and for shock at up −shift and down −
shift.
(c) L position test. (1) While running in the L position, check to see that there is no up −shift to 2nd gear.
(2) While running in the L position, release the accelerator pedal and check the engine braking ef- fect.
Evaluation:
If there is no engine braking effect:
1stand reverse brake is defective. (3) Check for abnormal noise during acceleration and deceleration.
(d) R position test. Shift into the R position and fully depress the accelerator pedal and ch\
eck for slipping.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT3417
OK if hot
Add if hot
Q07273
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−137
1996 LAND CRUISER (RM451U)
(e) P position test.
Stop the vehicle on a grade (more than 5 °) and after shifting into the P position, release the parking
brake. Then, check to see that the parking lock pawl holds the vehicle i\
n place.
6. BASIC INSPECTION
(a) Check the fluid level.
HINT:
Drive the vehicle so that the engine and transmission are
at normal operating temperature.
Fluid temp.: 70 − 80°C (158 − 176° F)
Only use the COOL range on the dipstick as a rough refer-
ence when the ATF is replaced or the engine does not
run.
(1) Park the vehicle on a level surface and set the park-
ing brake.
(2) With the engine idling and the brake pedal de- pressed, shift the shift lever into all positions from P
to L position and return to P position.
(3) Pull out the dipstick and wipe it clean.
(4) Push it back fully into the pipe.
(5) Pull it out and check that the fluid level is in the HOT range.
If the level is at the low side, add new fluid. Fluid type: ATF DEXRON ®II
NOTICE:
Do not overfill.
(b) Check the fluid condition. If the fluid smells burnt or is black, replace it.
(c) Replace the ATF. (1) Remove the drain plug and drain the ATF.
(2) Reinstall the drain plug securely.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07308
AT3417
OK if hot
Add if hot
AT4252
0 − 1 mm
Q07309
DI−138
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
(3) With the engine OFF, add new fluid through the oil
filler pipe.
Fluid type: ATF DEXRON ®II
Capacity:
Dry fill: 11.0 liters (11.6 US qts, 9.7 Imp. qts)
Drain and refill: 1.9 liters (2.0 US qts, 1.7 Imp. qts)
(4) Start the engine and shift the shift lever into all posi-
tions from P to L position and then shift into P posi-
tion.
(5) With the engine idling, check the fluid level. Add fluid up to the COOL level on the dipstick.
(6) Check the fluid level at the normal operating tem- perature 70 − 80° C (158 − 176°F) and add as nec-
essary.
NOTICE:
Do not overfill.
(d) Check the fluid leaks.
Check for leaks in the transmission.
If there are leaks, it is necessary to repair or replace O −rings,
Seal packings, oil seals, plugs or other parts.
(e) Inspect and adjust the throttle cable. (1) Check that the throttle valve is fully closed.
(2) Check that the inner cable is not slack.
(3) Measure the distance between the outer cable endand stopper on the cable.
Standard distance: 0 − 1 mm (0 − 0.04 in.)
If the distance is not standard, adjust the cable by the adjusting
nuts.
(f) Inspect and adjust the shift lever position. When shifting the shift lever from the N position to other
positions, check that the lever can be shifted smoothly
and accurately to each position and that the position indi-
cator correctly indicates the position.
If the indicator is not aligned with the correct position, carry out
the following adjustment procedures. (1) Loosen the nut on the control rod.
(2) Push the control rod fully rearward.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07310Control Shaft Lever(b)
(c)
Q07311
Neutral Basic Line
Bolt
Groove
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−139
1996 LAND CRUISER (RM451U)
(3) Return the control shaft lever 2 notches to N posi-
tion.
(4) Set the shift lever to N position.
(5) While holding the shift lever lightly toward the R
position side, adjust the control rod nut.
(6) Tighten the control rod nut.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf)
(7) Start the engine and make sure that the vehicle moves forward when shifting the lever from the N to
D position and reverses when shifting it to the R
position.
(g) Inspec and adjust park/neutral positoin switch. Check that the engine can be started with the shift lever
only in the N or P position, but not in other positions.
If not as stated above, carry out the following adjustment proce-
dure.
(1) Loosen the park/neutral position switch bolt and set
the shift lever to the N position.
(2) Align the groove and neutral basic line.
(3) Hold in position and tighten the bolt.
Torque: 13 N·m (130 kgf·cm, 9 ft·lbf) For continuity inspect of the park/neutral position
switch, see page DI−169 .
(h) Check the idle speed. Idle speed:
650 ± 50 rpm (In N position and air conditioner OFF)
7. MECHANICAL SYSTEM TESTS
(a) Measure the stall speed. The object of this test is to check the overall performance of the transmis\
sion and engine by measuring
the stall speeds in the D and R positions.
NOTICE:
Do the that at normal operating ATF temperature 50 − 80°C (122 − 176° F).
Do not continuously run this test longer than 5 seconds.
To ensure safety, conduct this test in a wide, clear, level area which provides good traction.
The stall test should always be carried out in pairs. One technician should\
observe the condi-
tions of wheels or wheel stoppers outside the vehicle while the other is doin\
g the test.
(1) Chock the 4 wheels.
(2) Connect an OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(3) Fully apply the parking brake.
(4) Keep your left foot pressed firmly on the brake pedal.
(5) Start the engine.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010