1996 TOYOTA LAND CRUISER Workshop Manual

TF0854
TF0986
TF0857
Q07130
RemovalInstallation
Socket Wrench Socket Wrench
TR−8
−
TRANSFER TRANSFER ASSEMBLY
1996 LAND CRUISER (RM451U)
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
16. REMOVE 2 BEARING RACES FROM REAR CASE
17. REMOVE INPUT SHAFT ASSEMBLY
Using a plastic hammer, remove the input shaft assembly.
18. REMOVE IDLER GEAR ASSEMBLY, CENTER DIFFER-
ENTIAL ASSEMBLY, SHIFT FORK NO.1 AND SHIFT
FORK NO.1 SHAFT FROM FRONT CASE
19. SEPARATE SHIFT FORK NO.1 AND SHIFT FORK NO.1 SHAFT
(a) Using a pin punch and hammer, drive out the slotted spring pin.
(b) Separate the shift fork No.1 and shift fork No.1 shaft.
20. REMOVE SHIFT OUTER LEVER AND INNER LEVER
(a) Remove the nut and washer from the shift outer lever. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Using a brass bar, hammer and socket wrench, tap out the lever lock pin.
(c) Remove the shift outer lever, washer and inner lever from
the front case.
21. REMOVE OIL RECEIVER FROM FRONT CASE
Remove the bolt and oil receiver. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07131
SST
TF0867
I19645
Push
Free
−
TRANSFER TRANSFER ASSEMBLY
TR−9
1996 LAND CRUISER (RM451U)
22. REMOVE 2 BEARING RACES FROM FRONT CASE
(a) Using SST, remove the bearing race (for idler gear).
SST 09950−40010, 09950 −60010 (09951−00320)
HINT:
At the time of reassembly, please refer to the following item.
Using SST and a press, install the bearing race (for idler gear).
SST 09316−60011 (09316 −00011, 09316−00041)
(b) Using a brass bar and hammer, remove the bearing race
(for output shaft).
HINT:
At the time of reassembly, please refer to the following item.
Using SST and a press, install the bearing race (for the out put
shaft). SST 09316 −20011, 09316 −60011 (09316 −00011,
09316 −00031)
23. INSPECT TRANSFER INDICATOR SWITCH
Check that there is continuity between the terminals, as shown.
Switch PositionSpecified
PushContinuity
FreeNo continuity
If continuity is not as specified, replace the switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TF0862
SST
TR0CN−01
TF0863
SST
TF0864
SST
SST
TR−10
−
TRANSFER TRANSFER ASSEMBLY
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REPLACE SHIFT LEVER OIL SEAL
(a) Using a screwdriver, pry out the oil seal.
(b) Using SST and a hammer, drive in a new oil seal. SST 0608−00081, 09950 −70010 (09951−07150)
2. REPLACE INPUT SHAFT OIL SEAL
(a) Using SST and a hammer, drive out the oil seal. SST 09316−60011 (09316 −00011)
(b) Using SST and a hammer, drive in a new oil seal. SST 09316−60011 (09316 −00011, 09316−00031)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0B4−01
−
TRANSFER TRANSFER ASSEMBLY
TR−11
1996 LAND CRUISER (RM451U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page TR−4 ).
HINT:
Coat all of the sliding and rotating surfaces with gear oil before assem\
bly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0B5−01
TR−12
−
TRANSFER INPUT SHAFT
822
Author: Date:
1996 LAND CRUISER (RM451U)
INPUT SHAFT
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0B6−01
TF0870
Socket
Wrench
−
TRANSFER INPUT SHAFT
TR−13
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE REAR BALL BEARING
(a) Using a snap ring expander, remove the snap ring.
(b) Using a socket wrench and press, remove the rear ball
bearing.
2. REMOVE INPUT GEAR
(a) Using a snap ring expander, remove the snap ring.
(b) Using a press, remove the input gear.
3. REMOVE FRONT BALL BEARING
Using a press, remove the front ball bearing.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0B7−01
Q00533
TR−14
−
TRANSFER INPUT SHAFT
1996 LAND CRUISER (RM451U)
REASSEMBLY
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
assembly.
1. INSTALL FRONT BALL BEARING
Using SST and a press, install a new front ball bearing. SST 09527−30010
2. INSTALL INPUT GEAR
(a) Using a press, install the input gear.
(b) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)MarkThickness mm (in.)
A2.00 (0.0787)F2.50 (0.0984)
B2.10 (0.0827)G2.60 (0.1024)
C2.20 (0.0866)H2.70 (0.1063)
D2.30 (0.0906)J2.80 (0.1 102)
E2.40 (0.0945)−−
(c) Using a snap ring expander, install a new snap ring.
3. INSTALL REAR BALL BEARING
(a) Using SST and a press, install a new rear ball bearing.
SST 09316−60011 (09316 −00031)
(b) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)
A2.00 (0.0787)
B2.10 (0.0827)
C2.20 (0.0866)
D2.30 (0.0906)
E2.40 (0.0945)
(c) Using a snap ring expander, install a new snap ring.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0B8−01
Z15264
Front Taper Roller BearingIdler Gear
High and Low
Clutch SleeveNeedle Roller Bearing
Idler
Low Gear Rear Taper
Roller Bearing
−
TRANSFER IDLER GEAR
TR−15
825
Author: Date:
1996 LAND CRUISER (RM451U)
IDLER GEAR
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010