1996 TOYOTA LAND CRUISER Workshop Manual

−
BODY WINDSHIELD
BO−49
1996 LAND CRUISER (RM451U)
(b) Clean off the sealer oozing out from the masking tape with
a clean rag saturated in cleaner.
6. INSPECT FOR LEAKS AND REPAIR
(a) Do a leak test.
(b) Seal any leaks with auto glass sealer.
Part No. 08833−00030 or equivalent
7. INSTALL ROOF HEADLINING
8. INSTALL FRONT PILLAR GARNISHES
9. INSTALL ASSIST GRIPS
10. INSTALL SUN VISORS AND HOLDERS
11. INSTALL PERSONAL LIGHT COVER
12. INSTALL PERSONAL LIGHT ASSEMBLY
13. INSTALL INNER REAR VIEW MIRROR
14. INSTALL COWL LOUVER
15. INSTALL WIPER ARMS Torque: 20 N·m(205 kgf·cm, 15 ft·lbf)
16. INSTALL HOOD Torque: 18 N·m(185 kgf·cm, 13 ft·lbf)
17. ADJUST HOOD (See page BO−6)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO38S−01
BO−50
−
BODY QUARTER WINDOW GLASS
1284
Author: Date:
1996 LAND CRUISER (RM451U)
QUARTER WINDOW GLASS
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO38T−01
−
BODY QUARTER WINDOW GLASS
BO−51
1996 LAND CRUISER (RM451U)
REMOVAL
1. w/ No. 2 rear seat:
NO. 2 REAR SEAT
2. REMOVE BACK DOOR SCUFF PLATE
3. REMOVE QUARTER TRIM
4. REMOVE REAR SEAT SIDE GARNISH
5. REMOVE REAR DOOR SCUFF PLATE
6. REMOVE QUARTER PILLAR GARNISH
7. REMOVE REAR PILLAR GARNISH
8. REMOVE ASSIST GRIPS
9. LOOSEN ROOF HEADLINING
10. REMOVE VENT LOUVER AND QUARTER BELT MOULDING
(a) Remove the nut from the vent louver.
(b) Insert a screwdriver between the retainers and body to pry it loose.
HINT:
Tape the screwdriver tip before use.
(c) Pull out the vent louver.
(d) Pull out the clips from the edge of the panel, and remove the moulding.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO−52
−
BODY QUARTER WINDOW GLASS
1996 LAND CRUISER (RM451U)
11. If reusing the weatherstrip:
REMOVE QUARTER WINDOW GLASS
(a) Using a screwdriver loosen the weatherstrip from the
body.
NOTICE:
Be careful not to damage the body.
(b) Pry the lip of the weatherstrip outward from the interior part of the body flange.
(c) Pull the glass outwards and remove it with the weather- strip.
12. If using a new weatherstrip: REMOVE QUARTER WINDOW GLASS
(a) From outside of the vehicle, cut off the weatherstrip lip with a knife.
NOTICE:
Do not damage the body and the glass.
(b) Push the glass outwards and remove the glass.
(c) Remove the remaining weatherstrip.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO38U−01
−
BODY QUARTER WINDOW GLASS
BO−53
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. Slide Type:
REMOVE CENTER SASH
Remove the screw and weatherstrip.
2. REMOVE QUARTER WINDOW GLASS
Pull up the sash and remove the 2 glasses.
3. REMOVE QUARTER WINDOW GLASS RUN FROM SASH
4. REMOVE QUARTER WINDOW WEATHERSTRIP FROM SASH
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO38V−01
BO−54
−
BODY QUARTER WINDOW GLASS
1996 LAND CRUISER (RM451U)
REASSEMBLY
1. Slide type: INSTALL QUARTER WINDOW WEATHERSTRIP ON
SASH
NOTICE:
If the weatherstrip has hardened, it may develop leaks.
HINT:
Use a new one if possible.
2. INSTALL QUARTER WINDOW GLASS RUN
3. INSTALL QUARTER WINDOW GLASS
Pull up on the sash and install 2 glasses.
4. INSTALL CENTER SASH
Install the weatherstrip with the screw.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO38W−01
−
BODY QUARTER WINDOW GLASS
BO−55
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL WEATHERSTRIP ON GLASS
(a) Attach the weatherstrip to the glass.
NOTICE:
If the weatherstrip has hardened, it may develop leaks. Use
a new one if possible.
(b) Insert a cord into the groove of the weatherstrip all the way
around with the ends overlapping.
2. INSTALL QUARTER WINDOW GLASS
(a) Apply soapy water to contact surface of the weatherstrip lip and to the body flange.
HINT:
Begin installation in the middle of the lower part of the quarter
window glass.
(b) Hold the glass in position on the body.
(c) From the inside, pull on one cord at an angle so it pulls the
lip over the flange. From the outside, press the glass
along the weatherstrip until the glass is installed.
3. FIX IN GLASS
To make the glass fix snugly, tap from the outside with your
open hand.
4. INSPECT FOR LEAKS AND REPAIR
(a) Do a leak test.
(b) Seal any leak with auto glass sealer.
5. INSTALL ROOF HEADLINING
6. INSTALL ASSIST GRIPS
7. INSTALL REAR PILLAR GARNISH
8. INSTALL QUARTER PILLAR GARNISH
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO−56
−
BODY QUARTER WINDOW GLASS
1996 LAND CRUISER (RM451U)
9. INSTALL REAR DOOR SCUFF PLATE
10. INSTALL REAR SEAT SIDE GARNISH
11. INSTALL QUARTER TRIM
12. INSTALL BACK DOOR SCUFF PLATE
13. w/ No. 2 Rear Seat:
INSTALL NO. 2 REAR SEAT
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010