1996 TOYOTA LAND CRUISER Workshop Manual

BE1LU−01
−
BODY ELECTRICAL POWER SOURCE
BE−9
1147
Author: Date:
1996 LAND CRUISER (RM451U)
POWER SOURCE
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LV−01
BE−10−
BODY ELECTRICAL IGNITION SWITCH AND KEY UNLOCK WARNING
SWITCH
1148
Author: Date:
1996 LAND CRUISER (RM451U)
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LW−01
−
BODY ELECTRICAL IGNITION SWITCH AND KEY UNLOCK WARNING
SWITCHBE−11
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT IGNITION SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
LOCK−No continuity
ACC7 − 9Continuity
ON3 − 4, 6 − 7 − 9Continuity
START2 − 3 − 4
6 − 9 − 10Continuity
If continuity is not as specified, replace the switch.
2. INSPECT SWITCH CONTINUITY
ConditionTester connectionSpecified condition
SW OFF
(Key removed)−No continuity
SW ON (Key set)1 − 5Continuity
If continuity is not as specified, replace the switch.
3. INSPECT DOOR COURTESY SWITCH CONTINUITY
(See page BE−21 )
4. INSPECT SEAT BELT WARNING RELAY CIRCUIT
(See page BE−34 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LX−01
BE−12
−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
1150
Author: Date:
1996 LAND CRUISER (RM451U)
HEADLIGHT AND TAILLIGHT SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LY−01
−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
BE−13
1996 LAND CRUISER (RM451U)
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1LZ−01
BE−14
−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT LIGHT CONTROL SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
OFF−No continuity
TAILA2 − A11Continuity
HEADA2 − A11 − A13Continuity
If continuity is not as specified, replace the switch.
2. INSPECT HEADLIGHT DIMMER SWITCH CONTINU-
ITY
Switch positionTester connectionSpecified condition
FlashA9 − A12 − A14Continuity
Low beamA3 − A9Continuity
High beamA9 − A12Continuity
If continuity is not as specified, replace the switch.
3. INSPECT HEADLIGHT CONTROL RELAY CONTINU-
ITY
ConditionTester connectionSpecified condition
Constant1 − 2Continuity
Apply B+ between
terminals 1 and 2.3 − 4Continuity
If continuity is not as specified, replace the relay.
4. INSPECT TAILLIGHT CONTROL RELAY CONTINUITY
ConditionTester connectionSpecified condition
Constant1 − 2Continuity
Apply B+ between
terminals 1 and 2.2 − 3Continuity
If continuity is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
BE−15
1996 LAND CRUISER (RM451U)
5. INSPECT HEADLIGHT RETAINER CIRCUIT
(a) Connect the positive (+) leads from the battery to termi-
nals 1 and 6, and the negative ( −) lead to terminal 3.
(b) Connect the 3.4 W test bulb between terminal 7 and the positive (+) lead from the battery.
(c) Disconnect the positive (+) lead from terminal 1, and check that the test bulb is lighting.
(d) Connect the negative ( −) lead to terminal 5, and check
that the test bulb goes out.
If operation is not as specified, replace the relay.
6. INSPECT TAILLIGHT CIRCUIT
(a) Connect the positive (+) leads from the battery to termi- nals 1 and 6, and the negative ( −) lead to terminal 2.
(b) Connect the 3.4 W test bulb between terminal 8 and the positive (+) lead from the battery.
(c) Disconnect the positive (+) lead from terminal 1, and check that the test bulb is lighting.
(d) Connect the negative ( −) lead to terminal 5, and check
that the test bulb goes out.
If operation is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE1M0−01
BE−16
−
BODY ELECTRICAL HEADLIGHT AND TAILLIGHT SYSTEM
1996 LAND CRUISER (RM451U)
ADJUSTMENT
1. ADJUSTING HEADLIGHT AIM ONLY
(a) Put the vehicle in below conditions.
Make sure the body around the headlight is not de-
formed.
Park the vehicle on a level place.
The driver gets into the driver’s seat and puts the
vehicle in a state ready for driving (with a full tank).
Bounce the vehicle several times.
(b) Adjust headlight in vertical alignment.
If the gauge bubble is outside the acceptable range of the beam
angle gauge, adjust it using adjusting screw A.
HINT:
The beam angle will change about 0 °11’ with one mark.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010