1996 TOYOTA LAND CRUISER Workshop Manual

CO112−01
CO−4
−
COOLING WATER PUMP
1996 LAND CRUISER (RM451U)
REMOVAL
1. DRAIN ENGINE COOLANT
2. DISCONNECT NO.3 WATER BYPASS HOSE
3. DISCONNECT RADIATOR INLET HOSE
4. REMOVE DRIVE BELTS, FAN WITH FLUID COU- PLING, WATER PUMP PULLEY AND FAN SHROUD
(a) Stretch the belts and loosen the water pump pulley mounting nuts.
(b) Loosen the lock, pivot and adjusting bolts of the genera- tor, and remove the drive belts.
(c) Disconnect the oil cooler hose from the clamp on the fan shroud.
(d) Remove the 2 bolts holding the fan shroud to the radiator.
(e) Remove the 4 water pump pulley mounting nuts.
(f) Pull out the fan with fluid coupling, water pump pulley and
fan shroud.
(g) Remove the fan from the fluid coupling.
5. REMOVE WATER PUMP
Remove the 4 bolts, 2 nuts, water pump and gasket.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO113−04
−
COOLING WATER PUMP
CO−5
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT WATER PUMP
(a) Visually check the air hole and water hole for coolant leak-
age.
If leakage is found, replace the water pump.
(b) Turn the pulley seat and check that the water pump bear- ing moves smoothly and quietly.
If necessary, replace the water pump.
2. INSPECT FLUID COUPLING
Check the fluid coupling for damage and silicon oil leakage.
If necessary, replace the fluid coupling.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO114−02
CO−6
−
COOLING WATER PUMP
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL WATER PUMP
Install a new gasket and the water pump with the 4 bolts and 2
nuts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
2. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN WITH FLUID COUPLING AND DRIVE BELTS
(a) Install fan to the fluid coupling.
(b) Place the fan with fluid coupling, water pump pulley and fan shroud in position.
(c) Temporarily install the fan pulley mounting nuts.
(d) Install the fan shroud with the 2 bolts. Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
(e) Connect the oil cooler hose to the clamp on the fan
shroud.
(f) Install the drive belts with the adjusting bolt and pivot bolt.
(g) Stretch the belts tight and tighten the 4 water pump pulley mounting nuts.
(h) Adjust the drive belts (See page CH−2 ).
3. CONNECT NO.3 WATER BYPASS HOSE
4. CONNECT RADIATOR INLET HOSE
5. FILL RADIATOR WITH ENGINE COOLANT
6. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO0IU−03
−
COOLING THERMOSTAT
CO−7
702
Author: Date:
1996 LAND CRUISER (RM451U)
THERMOSTAT
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO115−01
CO−8
−
COOLING THERMOSTAT
1996 LAND CRUISER (RM451U)
REMOVAL
HINT:
Removal of the thermostat would have an adverse effect, causing a lowering of cooling efficiency. Do not
remove the thermostat, even if the engine tends to overheat.
1. DRAIN ENGINE COOLANT
2. REMOVE WATER INLET AND THERMOSTAT
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO0IW−06
−
COOLING THERMOSTAT
CO−9
1996 LAND CRUISER (RM451U)
INSPECTION
INSPECT THERMOSTAT
HINT:
The thermostat is numbered with the valve opening tempera-
ture.
(a) Immerse the thermostat in water and gradually heat the
water.
(b) Check the valve opening temperature. Valve opening temperature: 80 − 84° C (176 − 183°F)
If the valve opening temperature is not as specified, replace the
thermostat.
(c) Check the valve lift. Valve lift: 10 mm (0.39 in.) or more at 95° C (203°F)
If the valve lift is not as specified, replace the thermostat.
(d) Check that the valve is fully closed when the thermostat is at low temperatures (below 40 °C (104° F)).
If not closed, replace the thermostat.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO116−01
CO−10
−
COOLING THERMOSTAT
1996 LAND CRUISER (RM451U)
INSTALLATION
1. PLACE THERMOSTAT IN WATER PUMP
(a) Install a new gasket on to the thermostat.
(b) Align the thermostat jiggle valve with the protrusion of the
water inlet housing, and insert the thermostat in the water
inlet housing.
HINT:
The jiggle valve may be set within 15 ° of either side of the pre-
scribed position.
2. INSTALL WATER INLET
Install the water inlet with the 3 nuts. Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
3. FILL RADIATOR WITH ENGINE COOLANT
4. START ENGINE AND CHECK FOR LEAKS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO0IY−02
−
COOLING RADIATOR
CO−11
706
Author: Date:
1996 LAND CRUISER (RM451U)
RADIATOR
ON−VEHICLE CLEANING
NOTICE:
If using a high pressure type cleaner , be careful not to deform the fins of the radiator core. (i.e. Main-
tain a distance between the cleaner nozzle and radiator core)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010