FI0534
DI5OU−02
P22892DLC3TOYOTA
−Hand− Held Tester
−
DIAGNOSTICS ENGINE
DI−3
1996 LAND CRUISER (RM451U)
PRE−CHECK
1. DIAGNOSIS SYSTEM
(a) Description
When troubleshooting OBD II vehicles, the only dif-
ference from the usual troubleshooting procedure
is that you connect to the vehicle the OBD II scan
tool complying with SAE J1978 or TOYOTA hand −
held tester, and read off various data output from
the vehicle’s ECM.
OBD II regulations require that the vehicle’s on −
board computer lights up the Malfunction Indicator
Lamp (MIL) on the instrument panel when the com-
puter detects a malfunction in the computer itself or
in drive system components which affect vehicle
emissions. In addition to the MIL lighting up when
a malfunction is detected, the applicable Diagnostic
Trouble Codes (DTC) prescribed by SAE J2012 are
recorded in the ECM memory (See page DI−13).
If the malfunction does not reoccur in 3 trips, the MIL goes off
but the DTC remain recorded in the ECM memory.
To check the DTC, connect the OBD II scan tool or
TOYOTA hand−held tester to Data Link Connector
3 (DLC3) on the vehicle. The OBD II scan tool or
TOYOTA hand−held tester also enables you to
erase the DTCs and check freezed frame data and
various forms of engine data (For operating instruc-
tions, see the OBD II scan tool’s instruction book.).
DTC include SAE controlled codes and manufac-
turer controlled codes. SAE controlled codes must
be set as prescribed by the SAE, while manufactur-
er controlled codes can be set freely by the
manufacturer within the prescribed limits (See DTC
chart on page DI−13).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
DI5K9−03
Q08225
Q08634
TOYOTA Hand−held Tester
DLC3
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−131
1996 LAND CRUISER (RM451U)
PRE−CHECK
1. DIAGNOSIS SYSTEM
(a) Description
When troubleshooting OBD II vehicles, the only dif-
ference from the usual troubleshooting procedure
is that you connect to the vehicle the OBD II scan
tool complying with SAE J1978 or TOYOTA hand −
held tester, and read off various data output from
the vehicle’s ECM.
OBD II regulations require that the vehicle’s on −
board computer lights up the Malfunction Indicator
Lamp (MIL) on the instrument panel when the com-
puter detects a malfunction in the computer itself or
in drive system components which affect vehicle
emissions. In addition to the MIL lighting up when
a malfunction is detected, the applicable DTCs pre-
scribed by SAE J2012 are recorded in the ECM
memory (See page DI−13).
If the malfunction does not occurs in 3 trips, the MIL goes off but
the DTCs remain recorded in the ECM memory.
To check the DTCs, connect an OBD II scan tool or
TOYOTA hand−held tester to the DLC3 on the ve-
hicle. The OBD II scan tool or TOYOTA hand−held
tester also enables you to erase the DTCs and
check freeze frame data and various forms of en-
gine data (For operating instructions, see the OBDII
scan tool’s instruction book).
DTCs include SAE controlled codes and Manufac-
turer controlled codes.
SAE controlled codes must be set as prescribed by
the SAE, while Manufacturer controlled codes can
be set freely by the manufacturer within the pre-
scribed limits (See page DI−143).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
