1996 TOYOTA LAND CRUISER brake pads

BR1CS−04
BR−22
−
BRAKE FRONT BRAKE PAD
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REMOVE FRONT WHEEL
2. INSPECT PAD LINING THICKNESS
Check the pad thickness and replace pads if not within the
specification. Minimum thickness: 1.0 mm (0.039 in.)
3. REMOVE THESE PARTS:
Clip
2 pins
Anti−rattle spring
2 pads
4 anti−squeal shims
NOTICE:
The anti −rattle spring and clip can be used again provided
that they have sufficient rebound, no deformation, cracks
or wear, and have had all rust, dirt and foreign particles
cleaned off.
4. CHECK DISC THICKNESS AND RUNOUT (See page
BR−27 )
5. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti −squeal shims must be
replaced together with the pads.
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in the pistons with a hammer handle or an equiva- lent.
HINT:
Always change the pad on one wheel at a time as there
is a possibility of the opposite piston flying out.
If the piston is difficult to push in, loosen the bleeder plug
and push in the piston while letting some brake fluid es-
cape.
(c) Install the 2 anti−squeal shims to new pads.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BRAKE FRONT BRAKE PAD
BR−23
1996 LAND CRUISER (RM451U)
HINT:
Apply disc brake grease to both sides of the inner anti −squeal
shims (See page BR−21 ).
(d) Install the 2 pads.
HINT:
Apply disc brake grease to the caliper indicated by the arrows
(See page BR−33 ).
NOTICE:
Do not allow oil or grease to get on the rubbing face.
6. INSTALL ANTI −RATTLE SPRING AND 2 PINS
7. INSTALL CLIP
8. INSTALL FRONT WHEEL
9. CHECK THAT FLUID LEVEL IS AT MAX LINE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1CU−03
−
BRAKE FRONT BRAKE CALIPER
BR−25
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
(b) Use a container to catch the brake fluid as it drains out.
2. REMOVE CALIPER
Remove the 2 mounting bolts and caliper. Torque: 123 N·m (1,250 kgf·cm, 90 ft·lbf)
3. REMOVE THESE PARTS:
Clip
2 pins
Anti−rattle spring
2 pads
4 anti−squeal shims
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1D0−03
−
BRAKE REAR BRAKE PAD
BR−31
1996 LAND CRUISER (RM451U)
REPLACEMENT
1. REMOVE REAR WHEEL
Remove the wheel and temporarily fasten the disc with the hub
nuts.
2. INSPECT PAD LINING THICKNESS
Check the pad thickness through the caliper inspection hole
and replace pads if the thickness is not within the specification.
Minimum thickness: 1.0 mm (0.039 in.)
3. REMOVE BRAKE CALIPER
(a) Remove the sliding main pin and sliding sub pin.
(b) Remove the caliper and suspend it so the hose is not stretched.
HINT:
Do not disconnect the flexible hose.
4. REMOVE THESE PARTS:
(a) 2 brake pads
(b) Anti−squeal shim
(c) 4 pad support plates
(d) 2 pad wear indicator plates
NOTICE:
The pad support plates can be used again provided that
they have sufficient rebound, no deformation, cracks or
wear, and have had all rust, dirt and foreign particles
cleaned off.
5. CHECK DISC THICKNESS AND RUNOUT (See page BR−36 )
6. INSTALL PAD SUPPORT PLATES
7. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti −squeal shim and wear
indicator plates must be replaced together with the pads.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR−32
−
BRAKE REAR BRAKE PAD
1996 LAND CRUISER (RM451U)
(a) Install pad wear indicator plate to each pads.
(b) Install the anti−squeal shim to the outer pad.
(c) Install the 2 pads so the wear indicator plate is facing up-
ward.
NOTICE:
Do not allow oil or grease to get on the rubbing face.
8. INSTALL CALIPER
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in piston with a hammer handle or an equivalent.
HINT:
Always change the pads on one wheel at a time as there is a
possibility of the opposite piston flying out.
(c) Install the caliper carefully so the boot is not wedged.
(d) Install and torque the sliding main pin and sub pin. Torque: 88 N·m (900 kgf·cm, 65 ft·lbf)
9. INSTALL REAR WHEEL
10. CHECK THAT FLUID LEVEL IS AT MAX LINE
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BR1D2−01
BR−34
−
BRAKE REAR BRAKE CALIPER
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper, then disconnect the flexible hose from the cali-
per.
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)
(b) Use a container to catch the brake fluid as it drains out.
2. REMOVE CALIPER
Remove the 2 sliding pins and caliper. Torque: 88 N·m (900 kgf·cm, 65 ft·lbf)
3. REMOVE THESE PARTS:
(a) 2 pads with anti −squeal shim
(b) 4 pad support plates
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

MA0055
MA02T−03
MA−6
−
MAINTENANCE BRAKE
46
Author: Date:
1996 LAND CRUISER (RM451U)
BRAKE
INSPECTION
1. INSPECT BRAKE LINE PIPES AND HOSES
HINT:
Check in a well lighted area. Check the entire circumference
and length of the brake hoses using a mirror as required. Turn
the front wheels fully right or left before checking the front brake.
(a) Check all brake lines and hoses.
Check for damage.
Check for wear.
Check for deformation.
Check for cracks.
Check for corrosion.
Check for leaks.
Check for bends.
Check for twists.
(b) Check all clamps for tightness and connections for leak- age.
(c) Check that the hoses and lines are clear of sharp edges, moving parts and the exhaust system.
(d) Check that the lines installed in grommets pass through the center of the grommets.
2. INSPECT FRONT BRAKE P ADS AND DISCS (See page
BR−27 )
3. INSPECT REAR BRAKE PADS AND DISCS (See page
BR−36 )
4. INSPECT PARKING BRAKE LININGS AND DRUMS
(See page BR−42 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010