1998 MITSUBISHI MONTERO Service Manual

octane engine overheat gas mileage compression ratio brake pads wheelbase

Page 441 of 1501

MITSUBISHI MONTERO 1998 Service Manual Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement

Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Broken .................. A ............ Require replacement.
Leaking (hydraulic
mount) ................. A ............ Require replacement.
Mounting hole worn,
affecting performance .. A ............ Require replacement.
Mounting hole worn, not
affecting performance .. .. ........ No service suggested or
required.
Rubber deteriorated,
affecting performance .. A ............ Require replacement.
Rubber deteriorated, not
affecting performance .. .. ........ No service suggested or
required.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
\
\
\
\
\
\
\

ODOMETER DRIVES (MECHANICAL)
See SPEEDOMETER/ODOMETER DRIVES (MECHANICAL) .
ODOMETER HEADS (MECHANICAL)
See SPEEDOMETER/ODOMETER HEADS (MECHANICAL) .
OIL PANS
See TRANSMISSION PANS .
PANS
See TRANSMISSION PANS .
PILOT HOLES
See DOWEL PINS, GUIDES AND PILOT HOLES .
PRESSURE PLATES
PRESSURE PLATE INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Balance weight missing .. C ............ Require replacement.
Broken .................. A ............ Require replacement.
Contact surface
distorted .............. B ............ Require replacement.
Cracks .................. B ............ Require replacement.
Fingers bent ............ A ............ Require replacement.
Hard spots .............. B ............ Require replacement.

Page 442 of 1501

MITSUBISHI MONTERO 1998 Service Manual Scored .................. B ............ Require replacement.
Spring rate less than
specifications ......... B ............ Require replacement.
Worn, affecting
performance ............ A

Scored .................. B ............ Require replacement.
Spring rate less than
specifications ......... B ............ Require replacement.
Worn, affecting
performance ............ A ............ Require replacement.
Worn beyond
specifications ......... B ............ Require replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
\
\
\
\
\
\
\

PRESSURE SWITCHES
See SWITCHES.
RACES
See BEARINGS AND RACES .
RUBBER JOINTS (METALASTIC)
These joints may be found on half and/or drive shafts. They
are usually found on European vehicles featuring a three-lug drive
flange. They may be equipped with a centering ball or pin.
RUBBER JOINT (METALASTIC) INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Drive flange bent ....... A ............. Require repair or
replacement.
Drive flange damaged,
affecting performance .. A ............ Require replacement.
Rubber drive joint
cracked ................ 2 ............ Suggest replacement.
Rubber drive joint
damaged, affecting
performance ............ A ............ Require replacement.
Rubber drive joint split
between mounting holes . A ............ Require replacement.
Rubber drive joint torn at
mounting holes ......... A ............ Require replacement.
Rubber drive joint weather-
cracked ................ .. ........ No service suggested or
required.
\
\
\
\
\
\
\

SCREENS
See FILTERS AND SCREENS .
SEALS
SEAL INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Leaking ................. A ........... ( 1) Require repair or
replacement.
( 1) - Require inspection of mating and sealing surface and
repair or replace as necessary. Check vent. A plugged

Page 443 of 1501

$MITSUBISHI MONTERO 1998 Service Manual vent may force fluid past the seal.��\ ��\ ��\ ��\ ��\ ��\ ��\ �� SEALS$

vent may force fluid past the seal.\
\
\
\
\
\
\

SEALS (METAL-CLAD)
See SEALS.
SELECTOR INTERLOCK SYSTEMS
See
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS) .
SERVOS
See ACTUATORS (VACUUM) .
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS)
See:
ACTUATORS (ELECTRICAL)
CABLES
LINKAGES (EXTERNAL)
SWITCHES
SENSORS
SENSOR INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Inoperative ............. A ........... ( 2) Require repair or
replacement.
Leaking
(vacuum/fluid/air) ..... A ............ Require replacement.
Out of adjustment ....... B .......... ( 3) Further inspection
required.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting

Page 444 of 1501

MITSUBISHI MONTERO 1998 Service Manual performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repai

performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Inoperative includes intermittent operation or out of
specification.
( 3) - Follow OEM recommended adjustment procedures. Repair
or replace if out of specification.
\
\
\
\
\
\
\

SIDE COVERS
See TRANSMISSION PANS .
SLIP YOKES
See YOKES AND SLIP YOKES .
SOLENOIDS
See:
ACTUATORS (ELECTRICAL)
ACTUATORS (VACUUM)
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
SPEED SENSOR (ELECTRONIC WHEEL AND VEHICLE) INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Air gap incorrect ....... B ....... ( 1) Require adjustment or
replacement.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of hardware.
Attaching hardware
threads stripped
(threads missing) ...... A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... ( 2) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Contaminated ............ A ........... ( 3) Require repair or
replacement.
Inoperative ............. B ........... ( 4) Require repair or
replacement. Further
inspection required.
Leaking ................. A .. Require repair or replacement.
Loose ................... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Resistance out of

Page 445 of 1501

MITSUBISHI MONTERO 1998 Service Manual specification .......... B .. Require repair or replacement.
Sensor housing cracked .. 2 ............ Suggest replacement.
Terminal broken ......... A .. Require repair or replacement.
Te

specification .......... B .. Require repair or replacement.
Sensor housing cracked .. 2 ............ Suggest replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... (2) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead misrouted ..... B .... Require re-routing according
to vehicle manufacturer's
specifications.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - If a sensor is not adjustable, further inspection is
required to identify and correct cause.
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as metal particles
or water. Require repair or replacement.
( 4) - Inoperative includes intermittent operation or out of OEM
specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\

SPEEDOMETER-DRIVEN GEAR HOUSINGS
See SPEEDOMETER/ODOMETER DRIVES (MECHANICAL) .
SPEEDOMETER/ODOMETER DRIVES (MECHANICAL)
SPEEDOMETER/ODOMETER DRIVE (MECHANICAL) INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Inoperative ............. A ........ ( 1) Require replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Teeth broken ............ A .. Require repair or replacement.

Page 446 of 1501

MITSUBISHI MONTERO 1998 Service Manual Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Worn close to the end of
its useful life

Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Worn close to the end of
its useful life ........ 1 ............ Suggest replacement.
Worn, affecting
performance ............ A ............ Require replacement.
(1) - Inoperative includes intermittent operation.
\
\
\
\
\
\
\

SPEEDOMETER/ODOMETER HEADS (MECHANICAL)
SPEEDOMETER/ODOMETER HEAD (MECHANICAL) INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Lens broken ............. A ........... ( 1) Require repair or
replacement.
Lens cloudy ............. 2 ........... ( 1) Suggest repair or
replacement.
Lens missing ............ C ........... ( 1) Require repair or
replacement.
Malfunctioning .......... A ........... ( 2) Require repair or
replacement.
Noisy ................... 2 .. Suggest repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - If lens is available as a separate part, require
replacement of lens only.
( 2) - Includes inoperative, intermittent operation, failure
to perform all functions, out of OEM specification, or
out of range.
\
\
\
\
\
\
\

SPEEDOMETERS AND ODOMETERS (ELECTRONIC)
SPEEDOMETER AND ODOMETER (ELECTRONIC) INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack

Page 447 of 1501

MITSUBISHI MONTERO 1998 Service Manual type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... (1) Require repair or
replacement.
Co

type) leaking .......... A .. Require repair or replacement.
Connector melted ........ A ........... (1) Require repair or
replacement.
Connector missing ....... C ............ Require replacement.
Leaking ................. A ............ Require replacement.
Lens broken ............. A ........... ( 2) Require repair or
replacement.
Lens cloudy ............. 2 ........... ( 2) Suggest repair or
replacement.
Lens missing ............ C ........... ( 2) Require repair or
replacement.
Malfunctioning .......... A ........... ( 3) Require repair or
replacement.
Mechanical head noisy ... 2 .. Suggest repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - If lens is available as a separate part, require
replacement of lens only.
( 3) - Includes inoperative, intermittent operation, failure
to perform all functions, out of OEM specification,
or out of range.
\
\
\
\
\
\
\

SWITCHES
SWITCH INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Binding, affecting
performance ............ A .. Require repair or replacement.
Binding, not affecting
performance ............ 2 .. Suggest repair or replacement.
Broken .................. A .. Require repair or replacement.
Burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Burned, not affecting
performance ............ 2 ........... ( 1) Suggest repair or

Page 448 of 1501

MITSUBISHI MONTERO 1998 Service Manual replacement.
Cracked, affecting
performance ............ A .. Require repair or replacement.
Cracked, not affecting
performance ............

replacement.
Cracked, affecting
performance ............ A .. Require repair or replacement.
Cracked, not affecting
performance ............ 1 .. Suggest repair or replacement.
Leaking ................. A .. Require repair or replacement.
Malfunctioning .......... A ........... (2) Require repair or
replacement.
Melted, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Melted, not affecting
performance ............ 2 ........... ( 1) Suggest repair or
replacement.
Missing ................. C ............ Require replacement.
Out of adjustment ....... B .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Won't return ............ A .. Require repair or replacement.
Worn .................... 1 ............ Suggest replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Includes inoperative, intermittent operation, or
failure to perform all functions.
\
\
\
\
\
\
\

TONE WHEELS
See TOOTHED RINGS (TONE WHEELS) .
TOOTHED RINGS (TONE WHEELS)
If the toothed ring requires replacement and cannot be
replaced as a separate component, replace the assembly of which the
ring is a part.
TOOTHED RING (TONE WHEEL) INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Alignment incorrect ..... B .. Require repair or replacement.
Bent .................... B ............ Require replacement.
Contaminated, affecting
performance ............ A .... Require repair. Identify and
correct cause.
Cracked ................. B ............ Require replacement.
Loose ................... A ..... Require replacement of worn
parts.
Missing ................. C ............ Require replacement.
Number of teeth

Load next 8 pages

Page: < prev 1-10 ... 409-416 417-424 425-432 433-440 441-448 449-456 457-464 465-472 473-480 ... 1504 next >

adblue wheel alignment navigation fuel type dead battery open trunk maintenance schedule