1998 MITSUBISHI MONTERO Service Manual

headlight aiming key battery oil viscosity climate control tire pressure reset light

Page 1201 of 1501

$MITSUBISHI MONTERO 1998 Service Manual ��\ ��\ ��\ ��\ ��\ ��\ ��\ �� STRIKE OUT BUMPERS STRIKE OUT BUMPER INSPECTION$

\
\
\
\
\
\
\

STRIKE OUT BUMPERS
STRIKE OUT BUMPER INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A .......... Require replacement of
broken part.
Attaching hardware
corroded, affecting
structural integrity ... A .......... Require replacement of
corroded part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .......... Require replacement of
missing part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Missing ................. C ............ Require replacement.
Split ................... 1 ............ Suggest replacement.
\
\
\
\
\
\
\

STRUT RODS
STRUT ROD INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Adjusting nut seized .... A ........... ( 1) Require repair or
replacement.
Attaching hardware
bent ................... B ... Require repair or replacement
of bent part, if available;
otherwise, replace strut rod.
Attaching hardware
broken ................. A ... Require replacement of broken
part, if available; otherwise,
replace strut rod.
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace strut rod.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace strut rod.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace strut rod.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,

Page 1202 of 1501

MITSUBISHI MONTERO 1998 Service Manual if available; otherwise,
replace strut rod.
Attaching hardware
threads stripped
(threads missing) ...... A

if available; otherwise,
replace strut rod.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
strut rod.
Attaching (mating) hole
oversized .............. A ... Require repair or replacement
of frame.
Attaching point on frame
corroded, affecting
structural integrity ... A ........ Require repair of frame.
Bent .................... A ............ Require replacement.
Mating (attaching) hole
oversized .............. A ... Require repair or replacement
of frame.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ............ Require replacement.
(1) - Only required if an alignment is being performed.
\
\
\
\
\
\
\

STRUT UPPER BEARING PLATE ASSEMBLIES
NOTE: When the following guidelines indicate replacement of
bearing, only the bearing should be replaced if it is
available separately; otherwise, replace the bearing
plate assembly.
STRUT UPPER BEARING PLATE ASSEMBLY INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require replacement of broken
part, if available; otherwise,
replace bearing plate assembly.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace bearing
plate assembly.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace bearing plate assembly.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace bearing plate assembly.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
bearing plate assembly.
Bearing axial or radial
movement exceeds vehicle
manufacturer's

Page 1203 of 1501

MITSUBISHI MONTERO 1998 Service Manual specifications ......... B ............. Require replacement
of bearing.
Bearing binding ......... A ............. Require replacement

specifications ......... B ............. Require replacement
of bearing.
Bearing binding ......... A ............. Require replacement
of bearing.
Bearing missing ......... C ............. Require replacement
of bearing.
Bearing seized .......... A ............. Require replacement
of bearing.
Bent .................... B ............ Require replacement.
Holes distorted ......... A ............ Require replacement.
Missing ................. C ............ Require replacement.
Severely corroded,
affecting structural
integrity .............. A ............ Require replacement.
\
\
\
\
\
\
\

SWAY BAR LINKS
SWAY BAR LINK INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace link.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace link.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace link.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace link.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
link.
Ball and socket has
looseness (perceptible
vertical movement) ..... 1 ........ ( 1) Suggest replacement.
Ball and socket has
looseness that is
excessive .............. B ..... ( 1)( 2) Require replacement.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Grease boot cracked ..... 2 ........ ( 3) Suggest replacement.
Grease boot missing ..... 2 ........ ( 4) Suggest replacement.
Grease boot torn ........ 2 ........ ( 5) Suggest replacement.
Missing ................. C ............ Require replacement.
Nut on stud loose ....... A ............. ( 6) Require repair.
Stud bent ............... B ........ ( 7) Require replacement.
Stud broken ............. A ........ ( 7) Require replacement.
Threads damaged ......... A .. Require repair or replacement.

Page 1204 of 1501

MITSUBISHI MONTERO 1998 Service Manual Threads stripped (threads
missing) ............... A ........ (7) Require replacement.
( 1) - If manufacturers procedures for inspection exist, use
those procedures; otherwise, use an appr

Threads stripped (threads
missing) ............... A ........ (7) Require replacement.
( 1) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 2) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 3) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 5) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 6) - Check for bent stud or damaged taper hole.
( 7) - Check for damaged taper hole.
\
\
\
\
\
\
\

SWAY BARS
SWAY BAR INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require replacement of broken
part, if available; otherwise,
replace sway bar.
Attaching hardware
corroded, affecting
structural integrity ... A .......... Require replacement of
corroded part, if available;
otherwise, replace sway bar.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace sway bar.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace sway bar.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace sway bar.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
sway bar.
Bent .................... B ............ Require replacement.
Broken .................. A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ............ Require replacement.
\
\
\
\
\
\
\

TIE ROD ENDS (INNER AND OUTER)

Page 1205 of 1501

$MITSUBISHI MONTERO 1998 Service Manual TIE ROD END (INNER AND OUTER) INSPECTION��\ ��\ ��\ ��\ ��\ ��\ ��\ �� Condition$

TIE ROD END (INNER AND OUTER) INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace tie rod end.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace tie rod end.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace tie rod end.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace tie rod end.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
tie rod end.
Adjusting sleeve bent ... B ... Require replacement of sleeve
or tie rod end.
Adjusting sleeve clamps
out of position ........ B ................. Require repair.
Adjusting sleeve
corroded, affecting
structural integrity ... A ... Require replacement of sleeve
or tie rod end.
Adjusting sleeve
missing ................ C ... Require replacement of sleeve
or tie rod end.
Adjusting sleeve
seized ................. A ........... (1) Require repair or
replacement.
Adjusting sleeve
threads damaged ........ A ... Require repair or replacement
of sleeve or tie rod end.
Adjusting sleeve
threads stripped
(threads missing) ...... A ... Require replacement of sleeve
or tie rod end.
Binding ................. A .......... ( 2) Further inspection
required.
Grease boot cracked ..... 2 ........ ( 3) Suggest replacement.
Grease boot missing ..... 2 ........ ( 4) Suggest replacement.
Grease boot torn ........ 2 ........ ( 5) Suggest replacement.
Grease fitting broken ... A ... Require replacement of grease
fitting.
Grease fitting missing .. C ... Require replacement of grease
fitting.
Grease fitting
won't seal ............. A ... Require replacement of grease
fitting.
Grease seal missing ..... 2 ......... ( 4) Suggest replacement
of seal.

Page 1206 of 1501

MITSUBISHI MONTERO 1998 Service Manual Grease seal torn ........ 2 ......... (5) Suggest replacement
of seal.
Greaseable tie rod end
wont take grease ...... 2 ...... ( 6) S

Grease seal torn ........ 2 ......... (5) Suggest replacement
of seal.
Greaseable tie rod end
won't take grease ...... 2 ...... ( 6) Suggest replacement of
grease fitting.
Looseness (perceptible
horizontal movement) ... 1 ........ ( 7) Suggest replacement.
Looseness exceeds
manufacturer's
specifications ......... B ............ Require replacement.
Looseness that is
excessive .............. B ..... ( 7)( 8) Require replacement.
Nut on stud loose ....... A ........... ( 9) Require repair or
replacement of nut.
Seized .................. A ............. Require replacement
Stud bent ............... B ....... ( 10) Require replacement.
Stud broken ............. A ....... ( 10) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ....... ( 10) Require replacement.
( 1) - Only required if toe needs to be adjusted.
( 2) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 3) - Cracked grease boot will allow contaminants to enter
joint and will accelerate wear.
( 4) - Lack of grease boot will allow contaminants to enter
joint and will accelerate wear.
( 5) - Torn grease boot will allow contaminants to enter joint
and will accelerate wear.
( 6) - If greaseable tie rod end will not take grease after
replacing the grease fitting, suggest replacement of
tie rod end.
( 7) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and socket
movement. Use only moderate hand pressure.
( 8) - Excessive looseness is defined as being significant enough
to affect vehicle handling or structural integrity.
( 9) - Check for bent stud or damaged taper hole.
( 10 ) - Check for damaged taper hole.
\
\
\
\
\
\
\

TRACK BARS
TRACK BAR INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
incorrect .............. A .......... Require replacement of
incorrect part, if available;
otherwise, replace track bar.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;
otherwise, replace track bar.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace track bar.
Attaching hardware

Page 1207 of 1501

MITSUBISHI MONTERO 1998 Service Manual threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,

threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace track bar.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
track bar.
Bent .................... B ............ Require replacement.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Grease boot cracked ..... 2 ........ (1) Suggest replacement.
Grease boot missing ..... 2 ........ ( 2) Suggest replacement.
Grease boot torn ........ 2 ........ ( 3) Suggest replacement.
Holes distorted ......... A ............ Require replacement.
Looseness (perceptible
horizontal movement) ... 1 ........ ( 4) Suggest replacement.
Looseness that is
excessive .............. B ..... ( 4)( 5) Require replacement.
Nut on stud loose ....... A ........... ( 6) Require repair or
replacement of nut.
Seized .................. A ............ Require replacement.
Stud bent ............... B ........ ( 7) Require replacement.
Stud broken ............. A ........ ( 7) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications ......... B ............ Require replacement.
( 1) - Cracked grease boot will allow contaminants to enter
joint and will accelerate wear.
( 2) - Lack of grease boot will allow contaminants to enter
joint and will accelerate wear.
( 3) - Torn grease boot will allow contaminants to enter joint
and will accelerate wear.
( 4) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and socket
movement. Use only moderate hand pressure.
( 5) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural integrity.
( 6) - Check for bent stud or damaged taper hole.
( 7) - Check for damaged taper hole.
\
\
\
\
\
\
\

TRAILING ARMS
TRAILING ARM INSPECTION\
\
\
\
\
\
\

Condition Code Procedure
Attaching hardware
broken ................. A ... Require replacement of broken
part, if available; otherwise,
replace trailing arm.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part, if available;

Page 1208 of 1501

MITSUBISHI MONTERO 1998 Service Manual otherwise, replace trailing
arm.
Attaching hardware
missing ................ C .. Require replac

otherwise, replace trailing
arm.
Attaching hardware
missing ................ C .. Require replacement of missing
part, if available; otherwise,
replace trailing arm.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads,
if available; otherwise,
replace trailing arm.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads, if
available; otherwise, replace
trailing arm.
Bent .................... B ............ Require replacement.
Bushing hole oversized .. B ............ Require replacement.
Corroded, affecting
structural integrity ... A ............ Require replacement.
Holes distorted ......... A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped
(threads missing) ...... A ............ Require replacement.
\
\
\
\
\
\
\

WHEEL BEARINGS, RACES AND SEALS
NOTE: When replacing or repacking wheel bearings, grease seal
replacement is required. You are not required to replace
these components in axle sets. Determine the need to
replace based upon the individual component conditions
that follow.
WHEEL BEARING, RACE AND SEAL INSPECTION
\
\
\
\
\
\
\

Condition Code Procedure
Rear axle seal on rear-
wheel drive leaking .... A ..... Require replacement of seal
and inspection of axle,
bearing, housing,
and vent tube.
Seal bent ............... 1 ............ Suggest replacement.
Seal leaking ............ A . Require replacement of seal and
inspection of bearings.
Seal missing ............ C ............ Require replacement.
Seal torn ............... A ............ Require replacement.
Wheel bearing
assembly feels rough
when rotated ........... A .. Require replacement of bearing
assembly.
Wheel bearing balls
are pitted ............. A .. Require replacement of bearing
assembly.
Wheel bearing balls
are worn ............... A .. Require replacement of bearing
assembly.
Wheel bearing end-play
exceeds vehicle
manufacturer's
specifications ......... B .. Require adjustment of bearing,

Load next 8 pages

Page: < prev 1-10 ... 1169-1176 1177-1184 1185-1192 1193-1200 1201-1208 1209-1216 1217-1224 1225-1232 1233-1240 ... 1504 next >

technical data clock coolant reservoir child seat heating cabin filter