1998 MITSUBISHI MONTERO coolant level
[x] Cancel search: coolant levelPage 63 of 1501
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - Refer to manufacturer's diagnostic trouble code
procedure and require repair or replacement of
affected component(s).
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement. Check for accepted cleaning procedure.
( 4) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable.
\
\
\
\
\
\
\
COOLANT
COOLANT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Acidity (pH) incorrect .. 1 ........... Suggest correction or
replacement.
Contaminated ............ B ...... ( 1) Require replacement or
recycling. Further
inspection required.
Level incorrect ......... B .......... ( 2) Require filling to
proper level.
Maintenance intervals ... 3 ........ ( 3) Suggest replacement.
Mixture incorrect ....... B ........... Require correction or
replacement.
Type incorrect .......... B ............ Require replacement.
( 1) - Determine source of contamination and require correction
prior to coolant replacement.
( 2) - Determine source of incorrect level and suggest repair.
( 3) - The system should be drained and/or flushed and
refilled with correct coolant according to OEM
recommended service interval and procedures.
\
\
\
\
\
\
\
COOLING FAN BLADES
COOLING FAN BLADE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Page 93 of 1501
A/C SWITCH
Removal & Installation
Lower glove box. Remove instrument cover. Remove lap cooler
and foot shower ducts. Remove center panel and A/C-heater control
panel. Remove bezel and knob. Disconnect A/C switch connector, and
remove A/C switch. To install, reverse removal procedure.
A/C ENGINE COOLANT TEMPERATURE SWITCH
Removal & Installation
Drain coolant below level of thermostat housing. See Fig. 8.
Remove A/C engine coolant temperature switch wiring harness connector,
and unscrew A/C engine coolant temperature switch from thermostat
housing. To install, reverse removal procedure. Tighten A/C engine
coolant temperature switch to specification. See TORQUE SPECIFICATIONS
. Add coolant and check for leaks.
Fig. 8: Locating A/C Engine Coolant Temperature Switch
Courtesy of Mitsubishi Motor Sales of America.
BLOWER MOTOR & RESISTOR
Removal & Installation
Remove right side foot shower duct. Disconnect blower and/or
resistor. Remove blower motor and/or resistor. See Fig. 9. To install,
reverse removal procedure.
Page 587 of 1501
Engine pre-oiling can be done using pressure oiler (if
available). Connect pressure oiler to cylinder block oil passage
such as oil pressure sending unit. Operate pressure oiler long enough
to ensure correct amount of oil has filled crankcase. Check oil level
while pre-oiling.
If pressure oiler is not available, disconnect ignition
system. Remove oil pressure sending unit and replace with oil pressure
test gauge. Using starter motor, rotate engine starter until gauge
shows normal oil pressure for several seconds. DO NOT crank engine
for more than 30 seconds to avoid starter motor damage.
Ensure oil pressure has reached the most distant point from
the oil pump. Reinstall oil pressure sending unit. Reconnect ignition
system.
INITIAL START-UP
Start the engine and operate engine at low speed while
checking for coolant, fuel and oil leaks. Stop engine. Recheck coolant
and oil level. Adjust if necessary.
CAMSHAFT
Break-in procedure is required when a new or reground
camshaft has been installed. Operate and maintain engine speed between
1500-2500 RPM for approximately 30 minutes. Procedure may vary due to
manufacturers recommendations.
PISTON RINGS
Piston rings require a break-in procedure to ensure seating
of rings to cylinder walls. Serious damage may occur to rings if
correct procedures are not followed.
Extremely high piston ring temperatures are produced obtained
during break-in process. If rings are exposed to excessively high RPM
or high cylinder pressures, ring damage can occur. Follow piston ring
manufacturer's recommended break-in procedure.
FINAL ADJUSTMENTS
Check or adjust ignition timing and dwell (if applicable).
Adjust valves (if necessary). Adjust carburetion or injection idle
speed and mixture. Retighten cylinder heads (if required). If
cylinder head or block is aluminum, retighten bolts when engine is
cold. Follow the engine manufacturer's recommended break-in procedure
and maintenance schedule for new engines.
NOTE: Some manufacturer's require that head bolts be retightened
after specified amount of operation. This must be done to
prevent head gasket failure.
Page 589 of 1501
CLUTCH PEDAL POSITION SWITCHES
COLD START INJECTORS
CONNECTORS
COOLANT
COOLANT RECOVERY TANKS
COOLING FAN MOTOR MODULES
COOLING FAN MOTOR RELAYS AND MODULES
COOLING FAN MOTOR RESISTORS
COOLING FAN MOTOR SENSORS AND SWITCHES
COOLING FAN MOTOR SWITCHES
COOLING FAN MOTORS
CRANKSHAFT POSITION SENSORS
DECEL VALVES
DEFLECTORS
DIP STICKS AND TUBES
DIP STICK TUBES
DISTRIBUTOR ADVANCES AND RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR BOOTS AND SHIELDS
DISTRIBUTOR CAPS
DISTRIBUTOR RETARDERS (MECHANICAL AND VACUUM)
DISTRIBUTOR ROTORS
DISTRIBUTOR SHIELDS
DISTRIBUTORS
EARLY FUEL EVAPORATION VALVES (HEAT RISER ASSEMBLIES)
EGR COOLERS
EGR EXHAUST MANIFOLD PASSAGES
EGR INTAKE AND EXHAUST MANIFOLD PASSAGES
EGR PLATES AND COOLERS
ELECTRONIC SPARK CONTROL MODULES
ELECTRONIC TRANSMISSION CONTROL DEVICES
ELECTRONIC TRANSMISSION FEEDBACK DEVICES
ENGINE COOLANT TEMPERATURE SENSORS
ENGINE COOLING SYSTEMS
ENGINE COVERS (OIL PAN, VALVE COVER, TIMING COVER)
ENGINE OIL
ENGINE OIL CANISTERS
ENGINE OIL COOLERS (EXTERNAL)
ENGINE OIL DRAIN PLUGS AND GASKETS
ENGINE OIL FILTERS AND CANISTERS
ENGINE OIL GASKETS
ENGINE OIL PRESSURE GAUGES (MECHANICAL)
EVAPORATIVE EMISSION (EVAP) CANISTER FILTERS
EVAPORATIVE EMISSION (EVAP) CANISTER PURGE DEVICES
EVAPORATIVE EMISSION (EVAP) CANISTERS
EVAPORATIVE EMISSION (EVAP) FEEDBACK DEVICES
EXHAUST GAS RECIRCULATION DEVICES
EXHAUST GAS RECIRCULATION FEEDBACK DEVICES
EXPANSION PLUGS
FAN CONTROL SENSORS
FUEL
FUEL ACCUMULATORS AND DAMPERS
FUEL AND COLD START INJECTORS
FUEL DAMPERS
FUEL DELIVERY CHECK VALVES
FUEL DISTRIBUTORS (BOSCH CIS)
FUEL FILLER NECKS AND RESTRICTORS
FUEL FILTERS
FUEL INJECTORS
FUEL LEVEL SENDERS7
FUEL PRESSURE REGULATORS
FUEL PUMPS (IN-TANK AND EXTERNAL, ELECTRICAL OR MECHANICAL)
FUEL RAILS
FUEL RESTRICTORS
Page 607 of 1501
replacement of part.
(2) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
BATTERIES
Proper operation of any electrical system or component can be
affected by battery condition. The battery(ies) must meet or exceed
minimum specification for vehicle as equipped and test to that
specific battery's CCA.
Definition of Terms
* Battery Performance Testing
Testing that determines whether or not a battery meets both
vehicle OEM and battery manufacturer's specifications.
* Cold Cranking Amp (CCA) Rating
The number of amperes a new, fully charged battery at
0
F (-17.8 C) can deliver for 30 seconds and maintain at
least a voltage of 1.2 volts per cell (7.2 volts for a
12-volt battery).
* Cranking Amps (CA)
The number of amperes a new, fully charged battery, typically
at 32
F (0 C) can deliver for 30 seconds and maintain at
least a voltage of 1.2 volts per cell (7.2 volts for a
12-volt battery).
* OEM Cranking Amps
The minimum CCA required by the original vehicle manufacturer
for a specific vehicle.
BATTERY INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Battery frozen .......... .. ......... ( 1) Further inspection
required.
Case leaking ............ A ............ Require replacement.
Casing swollen .......... A .......... ( 2) Further inspection
required.
Circuit open internally . A ............ Require replacement.
Electrolyte
contamination .......... A .......... ( 2) Further inspection
required.
Electrolyte
discoloration .......... A .......... ( 2) Further inspection
required.
Fails to accept and
hold charge ............ A ........ ( 3) Require replacement.
Fluid level low ......... B .......... ( 4) Further inspection
required.
Out of performance
specification
for battery ............ B ........ ( 5) Require replacement.
Out of specification for
application ............ B ........ ( 5) Require replacement.
Page 615 of 1501
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Inoperative includes intermittent operation or out of OEM
specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
COLD START INJECTORS
See FUEL AND COLD START INJECTORS .
CONNECTORS
See WIRING HARNESSES AND CONNECTORS .
COOLANT
COOLANT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Acidity (pH) incorrect .. 1 ........... Suggest correction or
replacement.
Contaminated ............ B ...... ( 1) Require replacement or
recycling. Further inspection
required.
Level low ............... B ... ( 2) Require filling to proper
level.
Maintenance intervals ... 3 ........ ( 3) Suggest replacement.
Mixture incorrect ....... B ........... Require correction or
replacement.
Type incorrect .......... B ............ Require replacement.
( 1) - Determine source of contamination and require
correction prior to coolant replacement.
( 2) - Determine source of incorrect level and suggest repair.
( 3) - The system should be drained and/or flushed and
refilled with correct coolant according to OEM
recommended service interval and procedures.
\
\
\
\
\
\
\
COOLANT RECOVERY TANKS
COOLANT RECOVERY TANK INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A .. Require repair or replacement
of hardware.
Attaching hardware
missing ................ C ......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A .. Require repair or replacement
of hardware.
Leaking ................. A . Require repair or replacement.
Page 629 of 1501
(1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Determine source of contamination, such as engine
coolant, fuel, metal particles, or water. Require
repair or replacement.
( 3) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable;
check for accepted cleaning procedure.
\
\
\
\
\
\
\
ENGINE COOLING SYSTEMS
NOTE: Overheating, poor engine performance, and insufficient
cabin heat can be affected by, but are not limited to,
all of the components in the engine cooling system.
ENGINE COVERS (OIL PAN, VALVE COVER, TIMING COVER)
ENGINE COVER (OIL PAN, VALVE COVER, TIMING COVER) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
incorrect .............. B ............ Require replacement.
Attaching hardware
loose .................. A .. Require repair or replacement.
Attaching hardware
missing ................ C ............ Require replacement.
Baffle loose ............ 2 .. Suggest repair or replacement.
Baffle missing .......... C ............ Require replacement.
Bent, affecting
performance ............ A .. Require repair or replacement.
Bent, not affecting
performance ............ .. ....... No service suggested or
required.
Cracked (not leaking) ... 2 .. Suggest repair or replacement.
Leaking externally ...... A .. Require repair or replacement.
Leaking internally,
causing fluid
contamination .......... A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
Restricted passage ...... A .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
\
\
\
\
\
\
\
ENGINE OIL
ENGINE OIL INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Contaminated ............ A .. ( 1) Require replacement of oil
and filter.
Level high .............. B ... Determine source of incorrect
level and require repair.
Level low ............... B ... Determine source of incorrect
level and require repair.
Maintenance intervals ... 3 ... Suggest replacement to comply
with vehicle's OEM recommended
service intervals.
( 1) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water when changing oil. Require
Page 631 of 1501
Further inspection required.
Canister attaching
hardware broken ........ A ... Require repair or replacement
of hardware.
Canister attaching
hardware loose ......... A ................. Require repair.
Canister attaching
hardware missing ....... C ............ Require replacement.
Canister attaching
hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Center tube collapsed ... A ........ (2) Require replacement.
Further inspection required.
Contaminated ............ A ...... ( 3) Require replacement of
oil and filter.
Dented .................. 2 ........ ( 4) Suggest replacement.
Further inspection required.
Leaking ................. A .. Require repair or replacement.
Maintenance intervals ... 3 ... Suggest replacement to comply
with vehicle's OEM recommended
service intervals.
( 1) - Inspect pressure relief valve.
( 2) - Inspect bypass.
( 3) - Determine cause of contamination, such as engine coolant,
fuel, metal particles, or water when changing oil. Require
repair or replacement.
( 4) - Determine cause, such as broken motor mount.
\
\
\
\
\
\
\
ENGINE OIL GASKETS
See ENGINE OIL DRAIN PLUGS AND GASKETS .
ENGINE OIL PRESSURE GAUGES (MECHANICAL)
ENGINE OIL PRESSURE GAUGE (MECHANICAL) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Indicates out of range .. B .......... ( 1) Further inspection
required.
Inoperative ............. A .......... ( 2) Further inspection
required.
Leaking ................. A .. Require repair or replacement.
Reads inaccurately ...... 2 .. Suggest repair or replacement.
( 1) - Gauge may indicate problem with contaminated oil, level,
pressure, or temperature, or problem with gauge.
( 2) - Gauge may indicate problem with contaminated oil, level,
pressure, or temperature, or problem with gauge.
Inoperative includes intermittent operation, out of OEM
specification, or out of range. Further inspection
required to determine cause.
\
\
\
\
\
\
\
EVAPORATIVE EMISSION (EVAP) CANISTER FILTERS
EVAPORATIVE EMISSION (EVAP) CANISTER FILTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure