1998 MITSUBISHI MONTERO oil type

Connector missing ....... C ............ Require replacement.
Inoperative ............. A ........ (2) Require replacement.
Insulation overheated ... A ............ Require replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Inoperative includes intermittent operation or out of
OEM specification.









\









\









\









\









\









\









\


BLOWER SWITCHES
See SWITCHES.
CABIN AIR FILTERS
CABIN AIR FILTER INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Air flow obstruction .... A ............. Require cleaning or
replacement.
Maintenance intervals ... 3 ............ Suggest replacement.
Missing ................. C ............ Require replacement.









\









\









\









\









\









\









\


CIRCUIT BREAKERS
See FUSES, FUSIBLE LINKS AND CIRCUIT BREAKERS .
COMPRESSOR CLUTCH ASSEMBLIES
COMPRESSOR CLUTCH ASSEMBLY INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Air gap incorrect ....... B .. Require repair or replacement.
Bearing seized .......... A .. Require replacement of bearing
or assembly.
Bearing worn, affecting
performance ............ A .. Require replacement of bearing
or assembly.
Coil shows signs of
overheating ............ 1 .... Suggest replacement of coil.
Connector broken ........ A .. Require repair or replacement.
Connector (Weatherpack
type) leaking .......... A .. Require repair or replacement.
Connector melted,

Bracket broken, affecting
performance ............ A ............ Require replacement.
Bracket broken, not
affecting performance .. .. ........ No service suggested or
required.
Bracket corroded,
affecting performance .. A .. Require repair or replacement.
Bracket corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Bracket cracked, affecting
performance ............ A .. Require repair or replacement.
Bracket cracked, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket holes elongated,
affecting performance .. A .. Require repair or replacement.
Bracket holes elongated,
not affecting
performance ............ .. ........ No service suggested or
required.
Bracket loose, affecting
performance ............ A .. Require repair or replacement.
Bracket loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Bracket missing ......... C ............ Require replacement.
Housing broken, affecting
performance ............ A .. Require repair or replacement.
Housing broken, not
affecting performance .. .. ........ No service suggested or
required.
Housing cracked, affecting
performance ............ A .. Require repair or replacement.
Housing cracked, not
affecting performance .. 1 .. Suggest repair or replacement.
Inoperative ............. A ........... (1) Require repair or
replacement.
Leaking ................. A .. Require repair or replacement.
Noisy ................... 2 ........... ( 2) Suggest repair or
replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Tubing connection
leaking ................ A .. Require repair or replacement.
( 1) - Inoperative includes intermittent operation or out of
OEM specification.
( 2) - Compressor noise can also be caused by low oil level,
state of charge, air contamination, or type of
refrigerant.









\









\









\









\









\









\









\


CONDENSER AIR SEALS
CONDENSER AIR SEAL INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Leaking ................. A . Require repair or replacement.
Missing ................. C ........... Require replacement.









\









\









\









\









\









\









\


CONDENSER FAN MOTORS

missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Contaminated, affecting
performance ............ A ............ Require replacement.
Dessicant bag
deteriorated ........... A ........ (1) Require replacement.
Further inspection required.
Dessicant at the end of
its useful life (saturated
with moisture) ......... 1 .. Suggest repair or replacement.
Fusible plug leaking .... A .... Require replacement of plug.
Leaking ................. A ............ Require replacement.
Pressure relief device
leaking ................ A . Require replacement of pressure
relief device.
Restricted .............. A .. Require repair or replacement.
Sight glass no longer
transparent ............ 2 ... Suggest replacement of drier.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Tubing connection
leaking ................ A .. Require repair or replacement.
( 1) - Inspect system to determine effects of dessicant bag
deterioration.









\









\









\









\









\









\









\


REFRIGERANT
NOTE: Refrigerants include any SNAP (Significant New Alternative
Policy)-approved blends.
REFRIGERANT INSPECTION









\









\









\









\









\









\









\


Condition Code Procedure
Contaminated (other than
refrigerant blends) .... B ........ Require service to remove
contamination.
Different types of
refrigerants in the same
system (other than
refrigerant blends) .... B ................. Require repair.
Overcharged ............. B ................. Require repair.
Refrigerant type
does not match
fittings and label ..... B ................. Require repair.
Undercharged ............ B ................. Require repair.









\









\









\









\









\









\









\


REFRIGERANT OIL
REFRIGERANT OIL INSPECTION








\









\









\









\









\









\









\


Condition Code Procedure
Contaminated ............ 1 .. Require repair or replacement.
Overfilled .............. B ................. Require repair.

A/C-HEATER SYSTEM
1998 Mitsubishi Montero
1998 AIR CONDITIONING & HEAT
Mitsubishi - A/C-Heater System
Montero
* PLEASE READ THIS FIRST *
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG RESTRAINT
SYSTEM article.
A/C SYSTEM SPECIFICATIONS
A/C SYSTEM SPECIFICATIONS TABLE








\









\









\









\









\









\






Application Specification
Compressor Type ............... Nippondenso 10PA15 10-Cyl.
Compressor Belt Deflection ( 1)
New .......................... 13/64-15/64" (5.1-6.0 mm)
Used ......................... 17/64-19/64" (6.6-7.5 mm)
Compressor Oil Capacity ..................... ( 2) 2.7 ozs.
Refrigerant (R-134a) Capacity ................. 21-23 ozs.
System Operating Pressures ( 4)
High Side ............... 149-213 psi (10.5-15.0 kg/cm
)
Low Side .................... 14-33 psi (1.0-2.3 kg/cm)
( 1) - With 22 lbs. (100 N.m) force applied midway on longest
span of belt.
( 2) - Use ND 8-OIL refrigerant oil.
( 3) - Use SUN PAG 56 refrigerant oil.
( 4) - With ambient temperature at about 80
F (27C).








\









\









\









\









\









\






DESCRIPTION
Slight variations exist among manual A/C-heater systems used.
On Montero, a Nippondenso 10-cylinder compressor is used. Cycling of
compressor clutch is controlled by an automatic A/C Control Unit
(ACCU).
Compressors will only operate within normal temperatures and
pressures set for each model. An electric condenser fan operates
whenever A/C system is operating. System components may vary depending
upon model. Systems may include an ACCU, fan switch, evaporator,
temperature sensor, dual-pressure switch, engine coolant temperature
switch, compressor, condenser, receiver-drier and various pipes and
hoses.
OPERATION
A/C CONTROL UNIT (ACCU)
ACCU controls cycling of compressor clutch based on
information received from air thermosensor and air inlet sensor, dual-
pressure switch, A/C switch and A/C engine coolant temperature switch.
ACCU is attached to top of evaporator housing.

Other Means Of Identification
Refrigerant R-134a, when viewed through a sight glass, may
have a "milky" appearance due to the mixture of refrigerant and
lubricating oil. As the refrigerant and oil DO NOT exhibit a "clear"
sight glass on a properly charged A/C system, most R-134a systems have
no sight glass.
REFRIGERANT OILS
NOTE: Use ONLY the specified oil for the appropriate system or A/C
compressor. Always check vehicle underhood A/C specification
label or A/C compressor label before adding refrigerant oil
to A/C compressor/system. See Figs. 2 and 3. Always use
refrigerant oil specified on vehicle underhood A/C
specification label if different from the following list.
Refrigerant R-12 based systems use mineral oil, while R-134a
systems use Polyalkylene Glycol (PAG) oils. Using a mineral oil based
lubricant with R-134a will result in A/C compressor failure due to
lack of proper lubrication. The following R-134a refrigerant oils are
currently specified:
Use DENSO/ND-Oil 8 refrigerant oil on Nippondenso
compressors. Use SUN PAG 56 refrigerant oil on Sanden compressors.
NOTE: PAG oils absorb moisture very rapidly, 2.3-5.6 percent by
weight, as compared to a mineral oil absorption rate of
0.005 percent by weight.
SERVICE EQUIPMENT
A/C systems using R-134a refrigerant and PAG lubricants
cannot use R-12 refrigerant or mineral oil lubricants. R-134a
refrigerant is NOT compatible or interchangeable with R-12
refrigerant. Separate sets of hoses, manifold gauge sets and
recovery/recycling equipment are required to service the different
systems. This is necessary to avoid cross-contaminating and damaging
A/C system. A single set of A/C service equipment cannot be cleaned
thoroughly enough to be used with both types of refrigerant.
All equipment used to service A/C systems using R-134a must
be U.L. listed and certified to meet SAE standard J2210. The service
hoses on the manifold gauge set must have manual (turn wheel) or
automatic back-flow valves at the service port connector ends. This
will prevent refrigerant from being released into the atmosphere.
For identification purposes, R-134a service hoses must have a
Black stripe along its length and be clearly labeled SAE J2196/R-134a.
The low pressure test hose is Blue with a Black stripe. The high
pressure test hose is Red with a Black stripe, and the center test
hose is Yellow with a Black stripe.
R-134a manifold gauge sets can be identified by one or all of
the following: Labeled FOR USE WITH R-134a on set, labeled HFC-134a or
R-134a on gauge face, or by a Light Blue color on gauge face. In
addition, pressure/temperature scales on R-134a gauge sets are
different from R-12 manifold gauge sets.
SYSTEM SERVICE VALVES
SCHRADER-TYPE VALVES
NOTE: Although similar in construction and operation to a tire
valve, NEVER replace a Schrader-type valve with a tire valve.

Schrader valve is similar in construction and operation to a
tire valve. When a test gauge hose with built-in valve core depressor
is attached, Schrader stem is pushed inward to the open position and
allows system pressure to reach gauge.
If test hose does not have a built-in core depressor, an
adapter must be used. Never attach hose or adapter to Schrader valve
unless it is first connected to manifold gauge set.
Refrigerant R-12 Schrader-type valve cores have TV5 thread
size. Refrigerant R-134a Schrader-type valve cores use M6 (Metric)
threads. See Fig. 1.
SERVICE VALVE LOCATIONS
SERVICE VALVE LOCATIONS TABLE








\









\









\









\









\









\






Vehicle High Low
Diamante ...................... ( 1) ................ ( 2)
Eclipse ....................... ( 1) ................ ( 2)
Galant ........................ ( 1) ................ ( 2)
Mirage ........................ ( 1) ................ ( 2)
Montero ....................... ( 3) ................ ( 3)
Montero Sport ................. ( 1) ................ ( 2)
3000GT ........................ ( 4) ................ ( 2)
( 1) - On high pressure line, between accumulator/receiver-
drier and evaporator.
( 2) - On low pressure line, between evaporator and
compressor.
( 3) - On top of accumulator/receiver-drier.
( 4) - On high pressure line, near receiver-drier.









\









\









\









\









\









\






REFRIGERANT RECOVERY/RECYCLING
Refrigerant recovery/recycling equipment is used to remove
refrigerant from vehicle's A/C system without polluting atmosphere. To
remove and recycle refrigerant, connect the recovery/recycling
equipment and following the equipment manufacturer's instructions.
Removed refrigerant is filtered, dried and stored in a tank
within the recovery/recycling equipment until it is ready to be pumped
back into vehicle A/C system. With refrigerant stored in the
recovery/recycling equipment, A/C system can be opened without
polluting atmosphere.
NOTE: Separate sets of hoses, gauges and refrigerant
recovery/recycling equipment MUST be used for R-12 and
R-134a based systems. DO NOT mix R-12 and R-134a
refrigerants, as their refrigerant oils and desiccants are
not compatible. It is NOT possible to clean equipment
thoroughly enough to prevent cross-contamination of A/C
systems. On systems with R-134a refrigerant, use
Polyalkylene Glycol (PAG) wax-free refrigerant oil.

A/C SYSTEM SPECIFICATIONS
1998 Mitsubishi Montero
1998 AIR CONDITIONING & HEAT
Mitsubishi - A/C System Specifications
Montero
A/C SYSTEM SPECIFICATIONS
A/C SYSTEM SPECIFICATIONS TABLE








\









\









\









\









\









\






Application Specification
Compressor Type ............... Nippondenso 10PA15 10-Cyl.
Compressor Belt Deflection ( 1)
New .......................... 13/64-15/64" (5.1-6.0 mm)
Used ......................... 17/64-19/64" (6.6-7.5 mm)
Compressor Oil Capacity ..................... ( 2) 2.7 ozs.
Refrigerant (R-134a) Capacity ................. 21-23 ozs.
System Operating Pressures ( 4)
High Side ............... 149-213 psi (10.5-15.0 kg/cm
)
Low Side .................... 14-33 psi (1.0-2.3 kg/cm)
( 1) - With 22 lbs. (100 N.m) force applied midway on longest
span of belt.
( 2) - Use ND 8-OIL refrigerant oil.
( 3) - Use SUN PAG 56 refrigerant oil.
( 4) - With ambient temperature at about 80
F (27C).








\









\









\









\









\









\

AXLE RATIO SPECIFICATIONS








\









\









\









\









\









\









\







Application Ratio
Montero ..................................................... 4.27:1
Montero Sport .................................................. (1)
( 1) - On vehicles equipped with wide fender, ratio is 4.64:1. On
vehicles with narrow fender, ratio is 4.27:1.









\









\









\









\









\









\









\







LUBRICATION
CAPACITY
DIFFERENTIAL FLUID CAPACITY








\









\









\









\









\









\









\







Application Specification
Montero & Montero Sport ............................ 2.4 Pts. (1.1L)\









\









\









\









\









\









\









\







FLUID TYPE
All models use fluid type SAE 80W-90/API GL-5.
TROUBLE SHOOTING
NOTE: See TROUBLE SHOOTING - BASIC PROCEDURES article in the
GENERAL TROUBLE SHOOTING section.
REMOVAL & INSTALLATION
AXLE SHAFTS R & I
Removal
1) Raise and support vehicle. Remove wheels and undercover.
Ensure hub is in free-wheeling position. Place transfer case in 2H
position. Remove drive hub cover, snap ring and shim from axle shaft.
See Fig. 3 . Remove brake calipers and support aside.
2) Disconnect tie rod assembly. Support lower control arm
with jack. Separate ball joints from knuckle. Remove knuckle and front
hub assembly. Using flat-blade pry bar, carefully remove left axle
shaft from differential carrier. DO NOT damage oil seal. On right axle
shaft, remove axle shaft-to-inner shaft flange retaining bolts. Remove
right axle shaft.
CAUTION: Replace circlips on BJ/DOJ splined shaft end.
Installation
1) Install right axle shaft on inner shaft flange. Install
new circlip on DOJ side of left axle shaft. Carefully install left
axle shaft into differential. DO NOT damage oil seal.
2) Reinstall knuckle with front hub assembly. To complete
installation, reverse removal procedure. Install shim and snap ring.
Check axle end play. See Fig. 4. End play should be .016-.028" (.4-.7
mm). If end play is not within specification, install correct shim.