1987 MAZDA 626 Workshop Manual

ON-VEHICLE MAINTENANCE 7B
OIL STRAINER
Removal
1. Jack up the vehicle and support it with safety
stands.
2. Drain the ATF.
3. Remove the left side splash shield.
86U07B-087
86U07B-088
Inspection
Check the following and repair or replace any faulty
parts.
1. Deformed or cracked oil pan
2. Deformed or clogged oil strainer
86U07B-089
Installation
1. Apply ATF to the O-ring and install it onto the oil
strainer.
2. Install the oil strainer.
Tightening torque:
8—11 Nm (80—110 cm-kg, 69—95 in-lb)
86U07B-090
7B-79

7B ON-VEHICLE MAINTENANCE
86U07B-091
76G07B-101
76G07B-102
3. Install the magnets on the oil pan as shown and
install the oil pan along with a new gasket.
Tightening torque:
8—11 Nm (80—110 cm-kg, 69—95 in-lb)
4. Add ATF, and with the engine idling, check the fluid
level and for leaks. (Refer to page 7B—71)
ADJUSTMENT OF 2-4 BRAKE BAND
1. Remove the oil pan. (Refer to page 7B—79)
2. Adjust the 2-4 brake band. (Refer to page 7B—211)
REPLACEMENT OF DRIVESHAFT OIL SEAL
Replace the oil seal in the same manner as for the
manual transaxle. (Refer to page 7A—9)
86U07B-094
7B-80

OH -VEHICLE MAmTENANSl
3. Remove
OIL COOLER
the oil cooler.
cSckmetollowing and repair or replace
2 Bent fins (repair w
any faulty
Installation Install the oi! cooler referring to installation note.
Installation note
OH cooler Install the oil cooler.
Tightening torque: 8—11 N-m (SO—1W cm-kg, 69—95 in-lb)
i5U07B-098 76-81

7B ON-VEHICLE MAINTENANCE
GOVERNOR (G4A-HL)
Removal
1. Remove the clip from the governor cover.
2. Remove the stopper bolt; then remove the gover-
nor assembly.
76G07B-103
Disassembly, Inspection and Assembly
Refer to Governor section of INSPECTION AND
REPAIR.
76G07B-104
Installation
Install in the reverse order of removal referring to in-
stallation note.
Installation note
Stopper bolt
Tighten the stopper bolt.
Tightening torque:
6—9 Nm (60—90 cm-kg, 52—78 in-lb)
76G07B-105
7B-82

REMOVAL 7B
REMOVAL
PRECAUTION
(1) Drain the ATF before removal.
(2) Jack up the vehicle and support it with safety stands after attaching the engine support.
Components
1. Battery
2. Battery carrier
3. Main fuse block
4. Distributor lead
5. Air flow meter connector
(G4A-EL)
6. Air cleaner assembly
(G4A-EL)
7. Air cleaner hose (G4A-EL)
8. Fresh air duct (G4A-HL)
9. Speedometer cable
10. Connectors
11. Grounds
12. Selector cable
13. Throttle cable
14. Front wheels
15. Splash shields
16. Oil cooler outlet and inlet
hoses
17. Tie-rod ends
18. Stabilizer bar control links
19. Lower arm ball joints
20. Driveshaft
21. Joint shaft bracket
76G07B-106
22. Joint shaft and driveshaft
23. Exhaust pipe bracket
24. Gusset plates
25. Under cover
26. Torque converter nuts
27. Manifold bracket (G4A-EL)
28. Starter
29. Engine mount No.4
30. Engine mount No.2
31. Crossmember and left side
lower arm
32. Transaxle
7B—83

7B REMOVAL
76G07B-107
G4A-EL
76G07B-108
76G07B-109
1. Remove the battery and battery carrier.
2. Disconnect the main fuse block.
3. Disconnect the distributor lead.
4. Disconnect the air flow meter connector and re-
move the air cleaner assembly. (G4A-EL)
5. Remove the air cleaner hose. (G4A-EL)
6. Remove the fresh air duct. (G4A-HL)
7. Disconnect the speedometer cable.
8. Disconnect the connectors.
(1) Inhibitor switch
(2) Solenoid valve
(3) Pulse generator (G4A-EL)
(4) Fluid temperature switch (G4A-EL)
9. Disconnect the grounds from the transaxle case.
10. Disconnect the selector cable.
11. Disconnect the throttle cable.
76G07B-110
7B—84

REMOVAL 7B
12. Remove the front wheels.
13. Remove the splash shields.
14. Drain the ATF.
15. Disconnect the oil cooler outlet and inlet hoses.
76G07B-111
16. Disconnect the tie-rod ends with the SST.
76G07B-112
17. Remove the stabilizer bar control links.
18. Remove the bolts and nuts at the left and right low-
er arm ball joints.
19. Pull the lower arms downward to separate them
from the knuckles.
Caution
Do not damage the ball joint dust boots.
76G07B-113
20. Separate the left driveshaft from the transaxle by
prying with a bar inserted between the shaft and
the case.
Caution
Do not damage the oil seal.
21. Remove the joint shaft bracket.
22. Separate the right driveshaft together with the joint
shaft in the same manner.
76G07B-114
7B—85

7B REMOVAL
76G07B-115
o ' ...
Exhaust pipe
hanger..
Gasset plate —
76G07B-116
23. Install the SST into the differential side gears.
Caution
Failure to install the SST may allow the
differential side gears to become misaligned.
24. Remove the exhaust pipe hanger and gusset
plates.
25. Remove the under cover.
26. Remove the torque converter nuts.
27. Remove the manifold bracket. (G4A-EL)
28. Remove the starter.
76G07B-117
49 G017 5A0
29. Suspend the engine with the SST.
76G07B-118
7B-86