1987 MAZDA 626 Workshop Manual

REMOVAL 7A
DOHC
76G07A-009
1. Battery
2. Main fuse block
3. Air cleaner assembly
4. Ventilation hose
5. Air hose
6. Ground(s)
7. Speedometer cable
8. Clutch release cylinder
9. Canister hose
10. Wheel
11. Splash sheild
12. Extension bar
13. Control rod
14. Stabilizer
15. Joint shaft
16. Surge tank bracket
17. Starter
18. Engine mount No.4
19. Engine mount No.2
20. Rear member (4WS)
21. Hunger rubber
22. Crossmember
7A—11

7A REMOVAL
Carburator
76G07A-010
15. Starter
16. Engine mount No.4
17. Engine mount No.2
18. Under cover
19. Hunger rubber
20. Crossmember
1. Battery
2. Air cleaner assembly
3. Ground
4. Speedometer cable
5. Clutch release cylinder
6. Canister hose
7. Wheel
8. Splash sheild
9. Extension bar
10. Control rod
11. Stabilizer
12. Joint shaft
13. Gusset plate (rear)
14. Gusset plate (front)
7 A-12

REMOVAL 7A
RF-N and RF-CX
1. Battery
2. Air cleaner assembly
3. Vacuum hose
4. Intercooler pipe and hose
(RF-CX)
5. Electric fan
6. Speedometer cable
7. Ground(s)
8. Clutch release cylinder
9. Pressure and return hoses
(power steering)
10. Starter
11. Wheel
12. Splash shield
13. Stabilizer
14. Joint shaft
15. Extension bar
16. Control rod
76G07A-011
17. Exhaust pipe bracket
18. Water pipe
19. Gusset plate (rear)
20. Gusset plate (front)
21. Under cover
22. Engine mount No.4
23. Engine mount No.2
24. Crossmember
7 A—13

7A REMOVAL
1. Remove the battery and battery carrier.
2. Disconnect the main fuse block. (Fl)
3. Disconnect the distributor lead.
4. Remove the air cleaner assembly.
76G07A-012
5. Remove the vacuum hose, the intercooler hose
(RF-CX) and the electric fan. (RF-N and RF-CX)
86U07A-021
8. Remove the front wheels.
9. Remove the splash shields.
10. Drain the transaxle oil.
86U07A-022
7A—14

REMOVAL 7A
86U07A-023
86U07A-024
86U07A-025
11. Disconnect the clutch release cylinder.
12. Disconnect the tie-rod ends using SST.
13. Remove the stabilizer bar control links.
14. Remove the bolts and nuts at the left and right low-
er arm bolt joints.
15. Pull the lower arms downward to separate them
from the knuckles.
Note
Do not damage the ball-joint dust boots.
16. Separate the left driveshaft from the transaxle by
prying with a bar inserted between the shaft and
the case.
Note
Do not damage the oil seal.
17. Remove the joint shaft bracket.
18. Separate the right driveshaft together with the joint
shaft in the same manner.
86U07A-026
7 A—15

7A REMOVAL
19. Install the SST to the differential side gear.
Note
Failure to install the SST may cause the
differential side gears to become misposi-
tioned.
86U07A-027
20. Remove the gusset plates, (except DOHC)
21. Remove the under cover, (except DOHC)
22. Remove the extension bar and the control rod.
76G07A-014
23. Remove the surge tank bracket. (Fl)
24. Remove the starter.
76G07A-015
25. Suspend the engine with the SST.
86U07A-030
7 A-16

REMOVAL 7A
26. Remove the engine mount No. 4 and bracket.
86U07A-031
86U07A-032
86U07A-033
27. Remove the engine mount No. 2.
28. Disconnect the hanger rubber then remove the
crossmember and the left side lower arm as an as-
sembly.
29. Lean the engine toward the transaxle.
30. Support the transaxle with a jack.
31. Remove the remaining transaxle mounting bolts.
32. Remove the transaxle.
86U07A-034
7 A—17

7A DISASSEMBLY
DISASSEMBLY
STEP 1
Disassemble in the sequence shown in the figure referring to disassembly note for the specially marked
parts.
76G07A-016
76G07A-017
24. Crank lever shaft
25. O-ring
26. Crank lever assembly
27. Shift fork and shift rod as-
sembly
28. Steel ball
29. Spring
30. Primary shaft gear as-
sembly
31. Secondary shaft gear as-
sembly
32. Differential assembly
33. Clutch housing
1. Rear cover
2. Lock nut
3. Lock nut
4. Primary reverse synchroniz-
er gear
5. Secondary reverse syn-
chronizer gear
6. Roll pin
7. Shift fork
8. Clutch hub assembly
9. Synchronizer ring
10. 5th gear
11. Gear sleeve
12. Secondary 5th gear
13. Lock bolt
14. Guide bolt
15. Lock bolt, ball and spring
16. Transaxle case
17. Magnet
18. Reverse idle shaft
19. Reverse idle gear
20. Lock bolt
21. Shift rod (5th and reverse)
and clip
22. Gate
23. Pin
7 A—18