1987 MAZDA 626 Workshop Manual

1 4 INSTRUMENT PANEL
INSTALLATION VIEW
67U14X-003
14—74

INSTRUMENT PANEL 1 4
86U14X-175
86U14X-176
REMOVAL
1. Remove the screws and remove the shift lever
knob (ATX).
2. Remove the shift lever knob (MTX).
3. Remove the rear console mounting screws.
4. Pull the console rearward and remove it.
86U14X-178
5. Remove the front console mounting screws.
86U14X-179
14—75

1 4 INSTRUMENT PANEL
6. Remove the steering wheel cap.
76G14X-026
7. Remove the steering wheel mounting nut.
76G14X-027
9. Remove the screws and remove the column covers
(upper and lower).
76G14X-028
14—76

INSTRUMENT PANEL 1 4
76G14X-029
10. Remove the screws and remove the under covers.
11. Loosen the nut and remove the hood release knob.
76G14X-030
86U14X-185
12. Remove the screws and pull out the meter hood.
13. Disconnect the connectors and remove the meter
hood.
14. Remove the screws and pull the meter assembly
outward.
15. Disconnect the speedometer cable at the
speedometer.
16. Disconnect the gauge connectors.
17. Remove the meter assembly.
86U14X-186
14—77

1 4 INSTRUMENT PANEL
86U14X-187
86U14X-188
86U14X-189
18. Remove the screws and pull the panel outward.
19. Disconnect the connectors and remove the switch
panel.
20. Remove the screws and remove the glove box.
21. Disconnect the glove box light connector.
22. Remove the center panel.
23. Remove the screws and slide out the heater con-
trol assembly.
24. Disconnect the control wires at the DEF, MAX-
COLD and REC positions (lever type control).
Note
Disconnect the connectors at the rear of the
control (Logicon type).
25. Remove the center cap.
26. Remove the instrument panel mounting bolt.
86U14X-190
14-78

INSTRUMENT PANEL 1 4
27. Remove the instrument panel side mounting bolts.
86U14X-191
28. Remove the instrument panel center bracket
mounting bolts.
86U14X-192
29. Remove the steering shaft mounting bolts.
86U14X-193
30. Disconnect the dash harness connectors.
31. Remove the instrument panel.
86U14X-194
14—79

14 INSTRUMENT PANEL
INSTALLATION
Install in the reverse order of removal, noting the fol-
lowing.
1. Tightening torque:

.^Torque Bolt
N-m (m-kg,
ft-lb)

©
4.22-6.18 (0.43-0.63, 3.10-4.54)

®(D
8.8-14 (0.9—1.4, 6.5—10)

©(D
8.8—14 (0.9—1.4, 6.5—10)

©@
8.8-14 (0.9-1.4, 6.5-10)
Steering wheel 39-49 (4.0—5.0, 29—36)

86U14X-195
2. Air-mix door control wire
a. Set TEMP lever at MAX—COLD position.
b. Connect the control wire and clamp it with the
shutter lever on the heater unit all the way to the
right side.
Caution
Move the temperature control lever to check
that the wire is secured. Also, check that it
moves the full stroke between HOT and COLD.
69G14X-224
3. Mode control wire
a. Set MODE control lever to DEF position.
b. Connect the control wire and clamp it with the
shutter lever on the heater unit at its closest point.
Caution
Move the mode lever to check that the wire
is secured. Also, check that it moves the full
stroke between DEF and VENT.
69G14X-225
, REC-FRESH air selector wire
a. Set the selector lever to REC position.
b. Connect the control wire and clamp it with the
shutter lever on the blower unit at its closest
point.
Caution
Move the recirculate-fresh air switch lever to
check that the wire is secured. Also, check
that it moves the full stroke between REC and
FRESH.
69G14X-226
14—80

SLIDING SUNROOF 1 4
SLIDING SUNROOF
STRUCTURAL VIEW
13. Guide rails
14. Guide
15. Packing
16. Tube assembly
17. Frame assembly
18. Sunroof relay
1. Sun shade
2. Slide panel
3. Weatherstrip
4. Deflector
5. Set plate
6. Drip rail
7. Lower panel
8. Lower panel cover
9. Decoration cover
10. Motor assembly
11. Guide brackets (rear)
12. Guide bracket (front)
14—81