Page 2481 of 2492
EXTERIOR PROTECTION
Front bumper (central section)
55S
55-12
REFITTING
Offer up the upper section of the bumper impact
absorber above the two guides (H).
To refit, proceed in the reverse order to removal.
ADAPTING THE PART FROM THE PARTS
DEPARTMENT FOR FITTING THE FRONT BUMPER
PROTECTOR (section 55-A)
NOTE: it is necessary to drill the central bumper when
this has a protector.
A Ø 10 mm
B Ø 17 mm
CCut according to the markings
17596R
18078R1
E
Page 2482 of 2492
EXTERIOR PROTECTION
Rear bumper
55PRear bumper
REMOVAL
After removing the rear wing extenders
(section 55-D),
Remove:
– the three lower mounting bolts (A),– the four upper mounting bolts (B),
– the luggage compartment lid balancers and its
mounting ball joint (C).
WARNING: the balancer acts as a door check strap. It
is necessary hold the cover using string.
Release the bumper.
REFITTING
To refit, proceed in the reverse order to removal.
18062R
17897R
55-13
F
Page 2483 of 2492
EXTERIOR PROTECTION
Front and rear door panels
55SFront and rear door panels
PRF5519
55-14
G
Page 2484 of 2492
EXTERIOR PROTECTION
Front and rear door panels
55P
55-15
REMOVING THE FRONT DOOR PANEL
Remove the blanking cover (A), and the panel
mounting bolt.
Protect the door using masking tape and then release
the panel using the unclipping pliers.REMOVING THE REAR DOOR PANEL
Remove the blanking cover (B), and the panel
mounting bolt.
Protect the door using masking tape and then release
the panel using the unclipping pliers.
18063R
17597S18064R
17542S
G
Page 2485 of 2492
EXTERIOR PROTECTION
Luggage compartment lid embellishers.
55PLuggage compartment lid embellishers.
REMOVAL
After removing the emergency spare wheel,
remove the lower mounting bolts (A).Protect the luggage compartment lid using masking
tape and then release the embellisher using the
unclipping pliers (six clips).
Disconnect the registration plate light connector.
REFITTING
To refit, proceed in the reverse order to removal.
17600R
17602S
17601S
55-16
H
Page 2486 of 2492
EXTERIOR ACCESSORIES
Rear wing corner extender
56P
156EXTERIOR ACCESSORIES
Rear wing corner extender
REMOVAL
Remove:
– the rear light,
– the two mounting bolts (A).
– the lower clip using a small flat screwdriver,
– the upper clip using the special clamp.Extender embellisher (B)
It is possible to remove this part, which avoids masking
before painting.
Apply pressure to the retaining brackets (C).
At the same time pull on the part which is held by the
double sided adhesive tape (D).
REFITTING
Apply double sided adhesive tape to the front
embellisher before reclipping it.
Check that the seals are positioned correctly (E).
To refit, proceed in the reverse order to removal.
17823R
16879-1R
56-1
A
Page 2487 of 2492
EXTERIOR ACCESSORIES
Rear windscreen wiper arm
56SRear windscreen wiper arm
PRF5606
WARNING: Use the special tool Elé. 1552 to remove the rear screen wiper arm.
56-2
B
Page 2488 of 2492
EXTERIOR ACCESSORIES
Rear windscreen wiper arm
56S
56-3
REMOVAL
After removing the emergency spare wheel,
remove the nut cover, unscrew the mounting nut on
the arm by one turn, insert the tool.
1 Extractor bolt (wedged on the loosened nut)
2 Short bend clip
3 Long bend clip
After unlocking the arm, remove the extractor then
complete the operation manually.
REFITTING
Tightening torque for the nut 11 ± 1 N.m
16834R
B