Page 2449 of 2492
UPPER REAR STRUCTURE
Upper hinge mounting support
44SUpper hinge mounting support
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the complete left hand
light support.
For standardisation purposes, the left hand light
support is delivered by the Parts Department without
the upper hinge mounting.
The rear face jig Car. 1563 (Parts Department
part no. 00 00 156 300) must be used.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with:
– upper hinge mounting angle bracket,
– upper hinge mounting angle bracket reinforcement.
PARTS CONCERNED (thickness in mm):
PRF4422
1Upper hinge mounting
2Upper hinge mounting reinforcement
3Light support
4Tail wheel arch3
2
1
1.2
44-23
L
Page 2450 of 2492
UPPER REAR STRUCTURE
Upper hinge mounting support
44P
44-24
644L1-17991
CAS13025-4R5
TOF15607-2R7
L
Page 2451 of 2492
UPPER REAR STRUCTURE
Upper hinge mounting support
44S
44-25
644L2-17989
TOL18021R5
L
Page 2452 of 2492
UPPER REAR STRUCTURE
Lower hinge mounting support
44SLower hinge mounting support
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the left hand light
support.
For standardisation purposes, the left hand light
support is delivered by the Parts Department without
the lower hinge mounting support.
The rear face jig Car. 1563 (Parts Departme
part no. 00 00 156 300) must be used.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Assembled part with lower hinge (bolted).
PARTS CONCERNED (thickness in mm):
PRF4424
1Lower hinge mounting support
2Light support5
1
44-26
M
Page 2453 of 2492
UPPER REAR STRUCTURE
Lower hinge mounting support
44P
44-27
644M1-17988
TOB18017R6
CAA11536-4R8
M
Page 2454 of 2492

UPPER REAR STRUCTURE
Luggage compartment lid stop mounting support
44Luggage compartment lid stop mounting support
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the complete end
panel or the right hand side end panel, part section.
For standardisation purposes, the end panel is
delivered by the Parts Department without the luggage
compartment lid stop mounting support.
The rear face jig Car. 1563 (Parts Department
part no. 00 00 156 300) must be used.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone.
PARTS CONCERNED (thickness in mm):
PRF4423
1Luggage compartment lid stop mounting
2Bumper mounting angle brackets
3Light support reinforcement,
4End panel upper cross member
5Bumper mounting angle bracket support1.5
1.8
1
1
1.8
44-28
N
Page 2455 of 2492
UPPER REAR STRUCTURE
Luggage compartment lid stop mounting support
44
44-29
644N1-17987
TOT18026-3R7
TOT18025-3R5
TOA15608-1R5
N
Page 2456 of 2492
NON-SIDE OPENING ELEMENTS
Tailgate
48P
148 NON-SIDE OPENING ELEMENTS
Tailgate
REMOVAL
Remove:
– the third brake light,
– the de-icing connections (B),
– the washer jet and disconnect.
Release:
– wiring harness (A),
– the two upper mounting protectors (C),
– the two hinge nuts (E),
– the balancers by removing the locking clips (D),
– the tailgate (this operation should be carried out be
two people for safety reasons).REFITTING
Before refitting it will be necessary to reseal between
the roof rear cross member and the hinges using
beading mastic.
Stick two strips of masking tape to the edge of the
tailgate, to prevent the paintwork from being scratched
during refitting.
Refit in reverse order to removal.
PRF4802
48-1
C