Page 1553 of 2492
Pages
Contents
INTERIOR BODY TRIMS71
71-1 Quarter light trims
TRIMS OF OPENINGS OTHER
THAN SIDE DOORS
73
73-1
73-5
73-7 Exterior hood trim
Padding
Interior hood trim
Trims and
upholstery
Page 1554 of 2492
INTERIOR BODY TRIMS
Quarter light trims
Remove:
- the cover and the nuts (1),
- the clips (2) and the bolt (3).
Unclip the fittings.
71
PRE7101
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
After removing the seat, the rear bench seat ba-
ckrest and the seat belt, unclip the insert.
Unclip the insert.
12282S
12283R
71-1
Page 1555 of 2492
TRIMS OF OPENINGS OTHER THAN SIDE DOORS
Exterior hood trim
Fold the hood in its housing.
Immobilise the hood cover in the case of the elec-
trohydraulic model.
73
PRE7301
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
Before carrying out any work, protect the seats
and the rear wings.
Open the hood, raise the front section beyond the
pushing point (neutral position).
Remove the front frame cover clamps.Unscrew the pin (1) and remove the locking han-
dle.
Unclip and remove the cover.
12431S
12432R
73-1
Page 1556 of 2492
TRIMS OF OPENINGS OTHER THAN SIDE DOORS
Exterior hood trim
73
Remove the upper side tensioning strap bolt (7).
12452
Unseat the front crossmember seal (2).
Remove:
- the bolt (3) and the seal (4) from the main
frame,
12453
- the front formed section tightening wrench
(5).
Unseat the frame front formed section (6).
12454
12455
Unseat the side formed section (8) from the front
crossmember.
73-2
Page 1557 of 2492
TRIMS OF OPENINGS OTHER THAN SIDE DOORS
Exterior hood trim
73
Unseat:
- the rear frame seal (11),
- the rear formed section (12) from the rear
frame.
Remove the exterior trim.
12456
Remove the rivet (9) from the side tensioning ca-
ble, remove the cable and the exterior trim.
Place the rear frame in a vertical position.
12457
Remove the rivet (10) from the main control rod
side tensioning strap.
12458
73-3
Page 1558 of 2492

TRIMS OF OPENINGS OTHER THAN SIDE DOORS
Exterior hood trim
73
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
Place the rear frame in a vertical position.
Seat the rear formed section (12) in the rear
frame.
Rivet (Ø 4×12) the side tensioning strap (10) to
the main control rod.
Pass the side tensioning cable (9) into the exterior
trim, rivet it (Ø 3×8) to the front crossmember.
Seat:
- the side formed section (8) on the front cross-
member,
- the front formed section (6) on the front
frame.
Fold the hood.
Clip the front formed section tightening wrench
(5).
Place the hood in the neutral position.
Secure:
- the side tensioning strap (7) to the main
frame,
- the main frame seal (4).
Place the rear frame in a vertical position.
Seat:
- the rear seal (12) on the rear frame,
- the front crossmember side seal (2).
Clip and clamp the front frame cover, secure the
handle, close the hood.
Adjustment of the windscreen aperture seal -
front crossmember side seal.
A clearance of 1 mm must be obtained between
the two seals by sliding the side seal.
In the event of sideways offset, slide the winds-
creen aperture seal as necessary after unseating it
at the front locks.
73-4
Page 1559 of 2492
TRIMS OF OPENINGS OTHER THAN SIDE DOORS
Padding
73
PRE7302
Removal
After removing the exterior hood trim, remove
the front formed section tightening wrench (1).
12460
Place the hood in neutral.Unseat the front formed section (2).
12461
Remove the tensioning strap bolts (3), remove the
rivets (4).
73-5
Page 1560 of 2492
TRIMS OF OPENINGS OTHER THAN SIDE DOORS
Padding
73
Remove:
- the bolts (5),
- the padding pulling to disengage the formed
section (6) from the rear roof arch groove.
RR R R
EE E E
FF F F
II I I
TT T T
TT T T
II I I
NN N N
GG G G
Engage the formed section (6) in the rear roof
arch groove and pull the padding aligning it at
the same time.
Tighten the bolt (5).
Rivet the tensioning strap (4) to the roof arches
and tighten it at the front (3) on the frame (Ø
3×10).
Seat the front formed section (2) in the groove,
align the padding.
Fit the front formed section tightening wrench
(1).
12462
73-6