Page 2393 of 2492
GENERAL INFORMATION
Repair Bench
40
40-23
III - REFERENCE POINTS FOR POSITIONING REPLACED PARTS (cont.)
F - FRONT SHOCK ABSORBER UPPER MOUNTING
The bracket rests under the shock absorber cup and is
centred in the shock absorber mounting holes.
It is used when replacing:
– a wheel arch,
– a front half unit.
It is also used when straightening.P - ENGINE MOUNTING
The bracket is positioned from above the engine
mounting and is centred in the mounting holes of the
pad.
It should be used with the mechanical units removed
to replace a front half unit.
17630R
17964R
Page 2394 of 2492
GENERAL INFORMATION
Repair Bench
40
40-24
III - REFERENCE POINTS FOR POSITIONING REPLACED PARTS (cont.)
D - REAR SUB-FRAME REAR MOUNTING
1 - Rear mechanical units removed
The bracket rests under the rear side member and is
centred in the sub-frame mounting hole.
It is used when replacing:
– the side member, part section,
– a rear unit.2 - Rear sub-frame in place
The bracket covers the sub-frame mounting bolt.
It should be used in the event of a rear collision for a
small impact.
17629R17723-1R
Page 2395 of 2492
GENERAL INFORMATION
Repair Bench
40
40-25
III - REFERENCE POINTS FOR POSITIONING REPLACED PARTS (cont.)
J - REAR SIDE MEMBER END
The bracket rests under the side member and is
centred in the pilot hole.
It should be used with the sub-frame in place to realign
a side member.
It should be used with the mechanical units removed,
under the same conditions, to replace a side member.L - END OF REAR END CROSS MEMBER
The bracket rests vertically against the rear end cross
member, and is then centred in the punching hole.
It should be used when replacing the rear end panel
assembly with or without the sub-frame.
17629R117629R2
Page 2396 of 2492
GENERAL INFORMATION
Repair Bench
40
40-26
BLACKHAWK
Page 2397 of 2492
GENERAL INFORMATION
Repair Bench
40
40-27
CELETTE
Page 2398 of 2492
GENERAL INFORMATION
Repair Bench
40
40-28
IV - SPECIAL TOOLING
BLACKHAWK
Special heads for MS System
Supplier’s Part No.: REN 87 998
additional to basic kit REN 87 995.
CELETTE
Special heads for System MZ
Supplier’s Part No.: 715.304
additional to kit 715.330.
For "Sevenne" benches, it will be necessary to order
belts with part number 715.SANGLE. These are not
delivered in the basic kit.
Please see the supplier's advice for fitting.Order from: BLACKHAWK S.A.
Centre Eurofret
Rue de Rheinfeld
67100 STRASBOURG
Order from: CELETTE S.A.
B.P. 9
38026 VIENNE
Page 2399 of 2492
GENERAL INFORMATION
Special tooling
40Special tooling
FRONT FACE JIG
18125R
Points (A) and (B) are the reference points for positioning the jig on the
vehicle.
The user must ensure that these points are correct when fault finding is
carried out before fitting.
Points (C), (D), (E) and (F) help with the mounting and positioning of the
replaced components.
If points (A) or (B) can no longer be used as a reference (detected during a
fault finding inspection), the positioning points on the side opposite the
impact fulfil this function.
40-29
Page 2400 of 2492
GENERAL INFORMATION
Special tooling
40
40-30
Car. 1546
Parts Stores reference:
00 00 154 600
IMPORTANT: the front face jig is not specific to the
4x4, it is also used for the new Scenic models.
17563R