Page 1529 of 2492
MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Front hood locks
52
PRE5202
Unscrew the pin (1) and remove the locking han-
dle.
Unclip and remove the cover.
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
OO O O
FF F F
TT T T
HH H H
EE E E
LL L L
OO O O
CC C C
KK K K
II I I
NN N N
GG G G
PP P P
LL L L
AA A A
TT T T
EE E E
Place the hood in the neutral position.
Remove the front frame cover clips.
Fold the hood in its housing.
Immobilise the hood cover in the case of the elec-
trohydraulic model.
12431S
12432R
12429R
Remove the locking plate bolts (2).
52-7
Page 1530 of 2492
MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Front hood locks
52
12427R
Remove the bolts (1).
RR R R
EE E E
FF F F
II I I
TT T T
TT T T
II I I
NN N N
GG G G
Refit the locks.
RR R R
EE E E
FF F F
II I I
TT T T
TT T T
II I I
NN N N
GG G G
Refit the locking plate and tighten the mounting
bolts (2) 8 N.m.
Clip and clamp the front frame cover.
Secure the handle.
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
OO O O
FF F F
TT T T
HH H H
EE E E
FF F F
RR R R
OO O O
NN N N
TT T T
LL L L
OO O O
CC C C
KK K K
SS S S
12434R
Remove the sun visors, the brackets.
Detach the roof console.
Detach the roof crossmember trim.
52-8
Page 1531 of 2492
MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Front hood locks
52
AA A A
DD D D
JJ J J
UU U U
SS S S
TT T T
MM M M
EE E E
NN N N
TT T T
12428R
The front part of the hood is positioned by mo-
ving part (2) in order to obtain dimension A = 4
mm.
Tighten the bolts (3) to a torque of 8 N.m.
Refit the trim, the console, the sun visors.
12435R
Hood closed and locked.
52-9
Page 1532 of 2492
MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Complete hydraulic system
52
12290R
Disconnect the wiring (1).
Remove the clips (2) and remove the ram.
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
After removing:
- the bench seat cushion and backrest,
- the quarter light trims,
- the boot side fittings
open the hood cover and immobilise it.Remove the connecting crossmember.
PRE5203
12172-1R
Open the bolt (A) as far as possible.
52-10
Page 1533 of 2492
MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Complete hydraulic system
52
Remove the rear roof arch ram pin (5) then the
clamp (6). Separate the ram. Remove:
- the main bearing mounting bolts (see section
52).
- the main ram upper clamp.
Separate the main ram from the frame.
Fold the hood.
Disconnect the hood microswitch wiring (left-
hand side)
Detach the hydraulic pipes.
Remove the main bearing mounting bolts.
Raise and immobilise the main bearings in order
to detach the hydraulic system clearance hole.
Remove:
- the electric relays bracket,
- the lower yoke nut (3),
- the ram.
12293R112291R
12289R
52-11
Page 1534 of 2492

MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Complete hydraulic system
52
RR R R
EE E E
FF F F
II I I
TT T T
TT T T
II I I
NN N N
GG G G
Insert the rams - pipes assemblies through the
clearance holes in the following order:
1 right-hand side assembly
2 left-hand side assembly
3 hood cover assembly.
Refit the pump.
After refitting all of the components, close the hy-
draulic unit bolt and operate the electrohydraulic
system several times (opening - closing) in order to
purge the hydraulic circuit.
WW W W
AA A A
RR R R
NN N N
II I I
NN N N
GG G G
:: : :
when work is carried out on the hy-
draulic system, follow the recommendations be-
low and keep everything clean.
• Before removal, clean the pipe unions, their
environment and the reservoir carefully.
• Place the system on thick paper. Do not use a
fluffy cloth.
• Cover the system carefully if the work is not
carried out immediately.
• Do not remove the replacement parts from
their packaging until immediately before they
are fitted.
• Do not blow with compressed air when the
hydraulic system is open.
OO O O
NN N N
LL L L
YY Y Y
use EE E E
SS S S
SS S S
OO O O
UU U U
NN N N
II I I
VV V V
II I I
SS S S
JJ J J
22 2 2
66 6 6
OO O O
II I I
LL L L for filling the hy-
draulic system. Disconnect the wiring.
Remove:
- the housing,
- the pump mounting bolts (4),
- the pump.
Remove the rams - pipes assemblies in the follo-
wing order:
1 hood cover assembly
2 left-hand side assembly
3 right-hand side assembly.
12172-1R1
52-12
Page 1535 of 2492
MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Hydraulic system (pipes)
52
Remove:
- the pump connectors (1) and wiring,RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
After removing the complete system, mark the co-
lour of the connectors (1) on the solenoid valves.
PRE5204
12298R
12297R
- the pump bolts (2) and bracket. B = blue
R = red
52-13
Page 1536 of 2492
MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Hydraulic system (pipes)
52
12299R
Diagram of fitting of pipes at the pump end
Unscrew the mounting bolts (3) of the pipe
concerned on the pump distributor (example:
pipe (E) for the hood cover ram).
Remove the pipe from the pump distributor.
Unscrew the union (4) on the ram.
Proceed in the same manner for the pipe (N) as
well as for the other groups of pipes.
RR R R
EE E E
FF F F
II I I
TT T T
TT T T
II I I
NN N N
GG G G
Coat the O-ring with hydraulic oil (change it if ne-
cessary).
NN N N
OO O O
TT T T
EE E E
:: : :
the hydraulic pipes are supplied in pairs
and are marked with letters at the unions.
12486S
12433S
Insert the pie union into the corresponding ope-
ning.
Tighten the bolts to a torque of 7 N.m.
52-14