Page 265 of 2492

INJECTION
Operating wiring diagram
17
E7J engine
COMPUTER TRACK ALLOCATION
TrackALLOCATION
1Power earth
2Electronic earth
3Vehicle speed information
4+ before ignition (permanent) computer memory
5Canister bleed signal (sequential earth period)
6Pump relay control (via track N° 2)
7Locking relay control (via track N° 2)
8Diagnostic line for erasing the memory and power assisted steering pressostat information
9Throttle position potentiometer information (pin N° 4 on 222)
10Heater relay command
11TDC sensor signal (track B)
12Rev counter information at instrument panel
13Connection with injection fault warning light on instrument panel
14Air temperature information
15Coolant temperature information
16+ 5 V feed for absolute pressure sensor and throttle potentiometer
17Common earth for absolute pressure sensor, throttle potentiometer and coolant temperature
sensor
18Emission of diagnostic signal to diagnostic socket
19Main computer feed via injection locking relay
20Air conditioning compressor command
21Injector control via earth
22Not used
23+ or - feed to idle speed micromotor (pin N° 1)
24+ or - feed to idle speed micromotor (pin N° 2)
17-41
Page 266 of 2492
INJECTION
Operating wiring diagram
17
E7J engine
TrackALLOCATION
25No load information input
26Not used
27Power module command
28TDC sensor signal input (track A)
29Immobiliser coded line input via decoder unit
30+ 12 V information when ignition turned on
31Pinking sensor noise signal input
32+ 12 V after ignition information
33Voltage information dependent on manifold pressure seen by sensor (on track B)
34Air conditioning compressor operation request input
35Voltage from oxygen sensor input
17-42
Page 267 of 2492
INJECTION
Operating wiring diagram
17
K7M engine
PRJ99475
17-43
Page 268 of 2492

INJECTION
Operating wiring diagram
17
K7M engine
COMPUTER TRACK ALLOCATION
TrackALLOCATION
1Not used
2Power earth n° 1
3Power earth n° 2
4Command for injector n° 2 and n° 3 via earth
5Air conditioning on - off information and request for compressor operation authorisation
(0 - 12 V)
6Heated windscreen information (0 - 12 V)
7Park / Neutral / torque reduction information (0 - 5 V) (K7M 703)
8Pinking sensor signal
9Stepping motor control (0 - 12 V)
10EGR solenoid valve control (0 - 12 V) (K7M 703)
11Bi-directional diagnostic line K used for entry into fault finding mode
(looking for computer), emission of diagnostic signals from computer, application of command
modes (G..*), erasing the memory (G0**)
and ending fault finding (G13*)
12Vehicle speed information
13Power assisted steering pressostat information
14Not used
15Coolant temperature sensor information
16Manifold pressure information transcribed by absolute pressure sensor
17Voltage information from oxygen sensor
18Earth
19Throttle position potentiometer information
20Air temperature sensor information
21Not used
22Not used
23Not used
24+ 12 V after ignition
17-44
Page 269 of 2492

INJECTION
Operating wiring diagram
17
TrackALLOCATION
25Not used
26Not used
27Not used
28Command for coil for cylinders 1 and 4
29Command for coil for cylinders 2 and 3
30Command for injector n° 1 and n° 4 via earth (n° 1 flywheel end)
31Pinking sensor screened cable
32+12 V before ignition
33TDC sensor signal (track B)
34TDC sensor signal (track A)
35Stepping motor command (0 - 12 V)
36Stepping motor command (0 - 12 V)
37Immobiliser coded line input
38Uni-directional diagnostic line L for entry into diagnostic mode only
(looking for computer)
39Not used
40Stepping motor command (0 - 12 V)
41Throttle angle information for automatic transmission computer
42RCO control (sequential earth period for canister bleed solenoid valve RCO)
43Command for injection fault warning light on instrument panel
44Common earth for pinking sensor and coolant temperature sensor and absolute pressure sensor
45+ 5 V feed for absolute pressure sensor and throttle position potentiometer
46Common earth for air temperature sensor and throttle position potentiometer
47Not used
48Command (via earth) for fuel pump relay and engine speed information
49Not used
K7M engine
17-45
Page 270 of 2492
INJECTION
Operating wiring diagram
17
TrackALLOCATION
50Fuel flow information for on board computer
51Air conditioning compressor clutch operation prevention command
(0 V → authorisation ; 12 V → prevention)
52Monitoring of injector feed and fuel pump feed from relay (236)
53Not used
54Not used
55Not used
K7M engine
17-46
Page 271 of 2492
INJECTION
Operating wiring diagram
17
F3R engine
PRJ99473
17-47
Page 272 of 2492

INJECTION
Operating wiring diagram
17
COMPUTER TRACK ALLOCATION
TrackALLOCATION
1Not used
2Power earth n° 1
3Power earth n° 2
4Command for injector n° 3 via earth
5Heated windscreen information (0 - 12 V)
6Air conditioning on - off information and request for compressor operation authorisation
(0 - 12 V)
7Park / Neutral / torque reduction information (0 - 5 V) (F3R 751)
8Pinking sensor signal
9Not used
10Not used
11Bi-directional diagnostic line K used for entry into fault finding mode
(looking for computer), emission of diagnostic signals from computer, application of command
modes (G..*), erasing the memory (G0**)
and ending fault finding (G13*)
12Vehicle speed information
13Fuel flow information for on board computer
14Not used
15Coolant temperature sensor information
16Manifold pressure information transcribed by absolute pressure sensor
17Voltage information from oxygen sensor
18Oxygen sensor earth
19Throttle position potentiometer information
20Air temperature sensor information
21Not used
22Not used
23Not used
24+ 12 V after ignition
F3R engine
17-48