Page 1977 of 2492
TOP OF BODY
Roof
45A
I
J
CAN11689R1a
K
CAP11696-2R1
L
TOP15254R1
M
N
CAW13602R2
1612
1
7
1 461 96 4
CAP11696-2R1
1 49
CAP11696-2R1
1 45
45-4
Page 1978 of 2492
TOP OF BODY
Roof
45A
O
P
CAJ11551-1R5 CAP11696-2R1
1
410
1 7 6
255a03-15312
15342R1
A = 70 mm
B = 500 mm
C = 500 mm
D = 300 mm
NOTE : apply a bead of adhesive mastic (C) in
zones (B) and (D) of the basic diagram, to rein-
force the roof where the roof bars are mounted.
E
Bead C
45-5
Page 1979 of 2492

TOP OF BODY
Roof acoustic cross member
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the roof for a
roll-over.
For reasons of standardisation, the Parts
Department only supplies parts for the version wi-
thout sunroof.Where a sunroof is fitted originally,
the roof and the centre roof cross member must
be cut according to the diagram below.
These cuts must also be made to fit a sunroof as an
accessory.
IMPORTANT : the roof cross member has a struc-
tural reinforcement function. For the version with
sunroof, the sunroof frame fulfils this function.
When fitting a sunroof as an accessory it is re-
commended that only sunroofs approved by the
Renault accessories department are used.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Single part.
PRE4502
45B
PARTS CONCERNED (thickness in mm) :
1Acoustic cross member 0.7
2Centre pillar reinforcement 1.5For sunroof
45-6
Page 1980 of 2492
TOP OF BODY
Roof acoustic cross member
LEFT HAND SIDE
255b01-15313
45B
RIGHT HAND SIDE
255b02-15316
A
CAA11536-3R6
B
CAA11536-5R6
1
2
1 2
45-7
Page 1981 of 2492
TOP OF BODY
Roof bow
PRE4503
45C
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the roof for a
roll-over.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Single part.
Bows (A) and (B) are mounted by rivets.
Bow (C) is spot welded.
PARTS CONCERNED (thickness in mm) :
1Roof bow 0.7
2Rear pillar upper reinforcement 1
3Roof bow support 1.2
45-8
Page 1982 of 2492
TOP OF BODY
Roof bow
BOWS A and B
255c01-15315
45C
A = rivet diameter 4.8 mm
(joint with bow support)
255c02-15314
B
CAA11536-3R6
1
2
45-9
Page 1983 of 2492
TOP OF BODY
Roof rear cross member
PRE4504
45D
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the roof for a
roll-over.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included. These are
dealt with in their respective section (refer to the
contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Single part.
PARTS CONCERNED (thickness in mm) :
1Roof rear cross member 0.7
2Rear quarter panel lining 0.7
3Rear corner reinforcement 1.2
45-10
Page 1984 of 2492
TOP OF BODY
Roof rear cross member
255d01-15318
45D
A
CAT13318R2
13
B
CAA11538-1R2
C
TOD14617R4
1 3
1
2
3
45-11