Page 65 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
E7J Engine
Remove the battery mounting bracket.
Disconnect the injection feed wire in the scuttle
panel as well as the starter motor feed.
98754R
Remove:
- the computer strap and secure it to the
engine,
- the wheels,
- the right hand and left hand mudguards,
98710R
- the brake calipers and secure them to the
body,
- catalytic converter,
- the two exhaust heat shields,
99612R
- the gear control on the gearbox side, turn it
over and secure to the exhaust pipe,
- the horn,
- the sub-frame-body tie rods,
- the front bumper.
PRJ1002
10-21
Page 66 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
E7J Engine
92442R
PREPARATION OF TOOL MOT. 1040-01
Fit the wheel pins into the lower holes (G).
This is secured to the sub-frame by hooks (I).
Secure tool Mot. 1040-01 underneath the sub-
frame.
98755R
Remove:
- the upper shock absorber bolts,
- the four sub-frame mounting bolts.
PRJ1003
Remove the engine and transmission assembly by
lifting the body.
98757S
Tie the spring - shock absorber units together
using rope.
Lower the 2 post lift until the tool comes into
contact with the floor.
10-22
Page 67 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
E7J Engine
REFITTING
The engine sub-frame can be easily aligned with
the bodywork by positioning the two
approximately 100 mm long threaded rods into
the two front mountings of the body sub-frame .
Refitting is the reverse of removal.
If the vehicle has manual steering, position the
shock absorber mountings into the holes (A), and
into holes (B) for power assisted steering.
92114-1R
Tighten all bolt, nuts and screws to the
recommended torques.
Fit the caliper mounting bolts using Loctite
FRENBLOC and tighten them to the correct
torque.
Press the brake pedal several times to bring the
pistons back into contact with the pads.
Fill:
- the cooling circuit and bleed it (see section
19),
- the engine and gearbox if required.
NOTE:
- check the steering shaft yoke spacer is in place
when refitting,
- ensure the heat shields are correctly
positioned.
10-23
Page 68 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
K7M engine
/ AT
SPECIAL TOOLING
Mot. 1040-01 Dummy cradle for removing and
refitting the engine and
transmission assembly
Mot. 1202 Hose clip pliers
Mot. 1311-06 Tool for removing fuel pipes
Front sub-frame mounting bolt 6
Rear sub-frame mounting bolt 11
Upper shock absorber cup mounting bolt 3
Wheel bolts 9
Brake caliper mounting bolt 3.5
Universal steering joint mounting bolt 3.5
Engine mounting pad nut on front
left hand side member mounting 7.5
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Drain:
- the cooling circuit from the lower radiator
hose,
- the engine if necessary.
Remove:
- the front wheels,
- the left and right hand mudguards,
- the sub-frame-body tie rods,
- the brake calipers and attach them to the
body,
98710R
- the front bumper,
PRJ1002
10-24
Page 69 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
K7M engine
/ AT
- the heat shield from the exhaust manifold,
- the catalytic converter (disconnect the oxygen
sensor) and attach the exhaust pipe to the
body,
- the horn,
- the tie rod between the shock absorber
turrets,
- the air filter,
- the earth strap,
- the absolute pressure sensor,
- the expansion bottle and attach it to the
engine.
Disconnect:
- the accelerator cable and the kickdown switch
connector,
- the brake servo pipe,
- the relay plate and the engine connection unit
connectors,
98756R2
- the automatic transmission computer
connector,
- the canister pipe.Remove the battery mounting bracket.
Disconnect:
- the injection feed wire in the scuttle panel
and the starter feed wire,
- the fuel supply and return pipes using tool
Mot. 1311-06, unclipping them from their
mounting,
99461R
- the heater hoses on the thermostat.
Unclip the radiator and hold it to one side by
attaching it to the engine.
10-25
Page 70 of 2492

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
K7M engine
/ AT
Remove:
- the automatic transmission gear selector
control,
- the nut and eccentric bolt (1) (use a roll pin
punch) from the steering yoke after pushing
the protector back.
97390-1R
SPECIAL NOTES FOR VEHICLES FITTED WITH A
DRIVER’S AIRBAG
IMPORTANT
To avoid any risks of destroying the rotary switch
under the steering wheel, comply with the
following instructions:
• Before removing the steering column and the
rack, the steering wheel MUST be immobilised
with the wheels straight using a "steering
wheel locking" tool, throughout the whole
operation.
• Any doubts about whether the steering wheel
is centred means that the steering wheel will
have to be removed so that the centring
method described in section 88 "Airbag" can
be applied.
REMINDER: in this case, only qualified, trained
staff can carry out this operation.
Fit a block between the automatic transmission
and the left hand sub-frame.
Remove the mounting nut for the rubber
mounting pad on the front left hand side member
mounting.
Using a copper hammer, tap the stud to release it
from the suspended mounting on the left hand
side.
92442R
PREPARATION OF TOOL MOT. 1040-01
Fit the wheel pins into the lower holes (G).
This is secured to the sub-frame by hooks (I).
10-26
Page 71 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
Secure tool Mot. 1040-01 under the sub-frame.
98755R
Lower the 2 post lift until the tool comes into
contact with the floor.
Remove:
- the upper shock absorber bolts,
- the four sub-frame mounting bolts.
PRJ1003
Remove the engine and transmission assembly by
lifting the body.
Tie the spring - shock absorber units together
using rope.
99588S
K7M engine
/ AT
10-27
Page 72 of 2492

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
K7M engine
/ AT
REFITTING
The engine sub-frame can be easily aligned with
the bodywork by positioning the two
approximately 100 mm long threaded rods into
the two front mountings of the body sub-frame .
Tighten the sub-frame mounting bolts to a torque
of :
•6 daN.m at the front,
•11 daN.m at the rear.
Refitting is the reverse of removal.
If the vehicle has manual steering, position the
shock absorber mountings into the holes (A), and
into holes (B) for power assisted steering.
92114-1R
Tighten all bolt, nuts and screws to the
recommended torques.
Fit the caliper mounting bolts using Loctite
FRENBLOC and tighten them to the correct
torque.
Press the brake pedal several times to bring the
pistons back into contact with the pads.
Fill:
- the cooling circuit and bleed it (see section
19),
- the engine and gearbox if required.
NOTE:
- check the steering shaft yoke spacer is in place
when refitting,
- ensure the heat shields are correctly
positioned.
10-28