Page 1545 of 2492
EXTERIOR ACCESSORIES
Exterior mirror
56
Remove:
- the bolt (1), the cover and the blanking piece.
- the mounting nuts (2).
12288R
12287R
56-1
Page 1546 of 2492
UPPER INTERIOR ACCESSORIES
Road box
Fit:
- the clamps to the cover (C),
- the compartment cover to the frame (B) and
secure it using bolts (HEX M5×12).
Degrease the foam strip (D) positioning grooves
(heptane surface cleaner).
Glue the strips.
58
PRE5801
AA A A
SS S S
SS S S
EE E E
MM M M
BB B B
LL L L
YY Y Y
Position the side panels (A) on the frame (B) and
secure them using bolts (HEX M4×8).
12477R
12478R
58-1
Page 1547 of 2492
UPPER INTERIOR ACCESSORIES
Road box
Secure it using the milled bolts and the crossed
nuts.
58
12468
With the hood folded and the hood cover open,
remove:
- the mounting nuts,
12467
- the bench seat cushion mounting bolts,
- the cushion.Unclip the seat belts.
Remove the bench seat backrest.
Clip the seat belt.
Fit:
- the carpet
- the road box (2 people).
12476R
58-2
Page 1548 of 2492
UPPER INTERIOR ACCESSORIES
Road box
CC C C
HH H H
AA A A
NN N N
GG G G
II I I
NN N N
GG G G
TT T T
HH H H
EE E E
BB B B
LL L L
II I I
NN N N
DD D D
LL L L
OO O O
CC C C
KK K K
II I I
NN N N
GG G G
MM M M
OO O O
TT T T
OO O O
RR R R
58
Close the hood cover.
Check the clearance (5 mm) between the
compartment and the hood cover.
If necessary, adjust the clearance using the nut (1).
Connect the electrical wiring (A).After removing the road box, disconnect the
motor harness (1).
Detach the locking rod (2).
Remove the mounting bolt (3).
12479R12475R
58-3
Page 1549 of 2492
77 11 192 972FF F F
EE E E
BB B B
RR R R
UU U U
AA A A
RR R R
YY Y Y
11 1 1
99 9 9
99 9 9
77 7 7Edition Anglaise
"The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods may be modified as a result of changes by the manufacturer in the
production of the various component units and accessories from which his vehicles
are constructed".All copyrights reserved by Renault.
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault.
CRenault 1997
Sealing and soundproofing
BODY SEALING
Page 1550 of 2492
Pages
Contents
Sealing and
soundproofing
WINDOW SEALING64
64-1 Windscreen pillar seal
Page 1551 of 2492
BODY SEALING
Windscreen pillar seal
Engage the seal in the retaining formed section
groove.
64
PRE6401
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
-- - -
RR R R
EE E E
FF F F
II I I
TT T T
TT T T
II I I
NN N N
GG G G
After removing the front locks and the trims, re-
move the seal.
Moisten the seal (glass cleaner, soapy water).Slide the seal so that the end (A) is positioned with
the corner of the windscreen aperture.
Close and lock the hood.
Check the sideways alignment with the hood seal.
A clearance of 1 mm must be obtained between
the seals (longitudinal clearance).
12437S
12436R
64-1
Page 1552 of 2492
77 11 192 972FF F F
EE E E
BB B B
RR R R
UU U U
AA A A
RR R R
YY Y Y
11 1 1
99 9 9
99 9 9
77 7 7Edition Anglaise
"The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods may be modified as a result of changes by the manufacturer in the
production of the various component units and accessories from which his vehicles
are constructed".All copyrights reserved by Renault.
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of
Renault.
CRenault 1997
Trims and upholstery
TRIMS OF OPENINGS OTHER THAN SIDE DOORS
INTERIOR BODY TRIMS