1995 RENAULT MEGANE SCENIC wheel bolt torque

ENGINE AND PERIPHERALS
Engine - Gearbox
10
E7J engine
SPECIAL TOOLING
B.Vi. 31-01 Set of punches
Mot. 1202 Hose clip pliers
T.Av. 476 Ball joint extractor
SPECIAL EQUIPMENT
Load positioning tool (example : NAUDER 1805)
Brake caliper bolts 3.5
Shock absorber base bolt 17
Track rod end nut 3.5
Driveshaft gaiter bolt 2.5
Wheel bolts 9
Engine tie-bar bolt :
- on the gearbox 6.5
- on the sub-frame 7.5
Right hand engine mounting nut 4.5
Left hand gearbox mounting nut 4.5
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Drain the gearbox.
Disconnect the battery.
Remove:
- the bonnet,
- the front wheels.Right hand side of the vehicle
Remove the pins from the right hand driveshaft
using tool B.Vi. 31-01.
Remove:
- the track rod end using tool T.Av. 476,
- the upper shock absorber bolt and slacken the
nut on the lower bolt without removing it.
Remove the driveshaft from the gearbox. Left hand side of the vehicle
Remove:
- track rod end using tool T.Av. 476,
- the three bolts of the driveshaft gaiter,
- the two bolts from the shock absorber base,
- the two bolts from the brake caliper then
secure it to the shock absorber spring,
- the bolt from the lower ball joint,
- the complete hub assembly and the
driveshaft.
10-4

ENGINE AND PERIPHERALS
Engine - Gearbox
10
K7M engine
SPECIAL TOOLING
Mot. 1202 Hose clip pliers
T.Av. 476 Ball joint extractor
B.Vi. 31-01 Set of punches
SPECIAL EQUIPMENT
Load positioning tool (example : NAUDER 1805)
Brake caliper mounting bolt 3.5
Shock absorber base bolt 17
Track rod end nut 3.5
Driveshaft gaiter mounting bolt 2.5
Wheel bolts 9
Engine tie-bar bolt :
- on the gearbox 6.5
- on the sub-frame 7.5
Right hand engine mounting nut 4.5
Left hand gearbox mounting nut 4.5
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Drain the gearbox.
Disconnect the battery.
Remove:
- the bonnet,
- the front wheels.Right hand side of the vehicle
Remove the pins from the right hand driveshaft
using tool B.Vi. 31-01.
Remove:
- the track rod end using tool T.Av. 476,
- the upper shock absorber bolt and slacken the
nut on the lower bolt without removing it.
Remove the driveshaft from the gearbox. Left hand side of the vehicle
Remove:
- track rod end using tool T.Av. 476,
- the three bolts of the driveshaft gaiter,
- the two bolts from the shock absorber base,
- the two bolts from the brake caliper then
secure it to the shock absorber spring,
- the bolt from the lower ball joint,
- the complete hub assembly and the
driveshaft.
10-7

ENGINE AND PERIPHERALS
Engine - Gearbox
10
F engine (E)
Load positioning tool (example: NAUDER 1805)
SPECIAL TOOLING
B. Vi. 31 -01 Roll pin punches
Mot. 1202 Hose clip pliers
Mot. 1273 Tool for checking belt tension
Mot. 1289 -03 Fork for centring suspended
engine mounting limiter
T.Av. 476 Ball joint extractor
SPECIAL EQUIPMENT
Brake caliper mounting bolts 3.5
Shock absorber base bolts 17
Driveshaft gaiter mounting bolts 2.5
Wheel bolts 9
Engine tie-bar bolt 4.5 to 6.5
Suspended engine mounting bolt
on gearbox 4
Nut for suspended engine mounting
pad on front left hand side member 7.5
Front right hand suspended engine
mounting cover bolt on engine 4
Front right hand suspended engine
mounting movement limiter bolt 6
Nut for engine mounting pad on front
right hand suspended engine
mounting cover 4.5
TIGHTENING TORQUES (in daN.m)REMOVAL
Put the vehicle on a two post lift.
Disconnect the battery.
Drain the gearbox.
Remove:
- the front wheels,
- the front right hand and left hand
mudguards.
98710R
10-10

ENGINE AND PERIPHERALS
Engine - Gearbox
10
F8Q engine
Load positioning tool (example : NAUDER 1805)
SPECIAL TOOLING
B. Vi. 31 -01 Roll pin punches
Mot. 1202 Hose clip pliers
Mot. 1311-06 Tool for removing fuel pipes
T.Av. 476 Ball joint extractor
SPECIAL EQUIPMENT
Brake caliper mounting bolt 3.5
Shock absorber base bolt 17
Track rod end 3.5
Lower ball joint nut 6.5
Driveshaft gaiter mounting bolt 2.5
Wheel bolts 9
Engine tie-bar bolt 6
Suspended engine mounting bolt
on gearbox 5.5
Bolt for suspended engine mounting
pad on front left hand side member 2.5
Front right hand suspended engine
mounting cover bolt on engine 4
Front right hand suspended engine
mounting movement limiter bolt 6
TIGHTENING TORQUES (in daN.m)REMOVAL
Put the vehicle on a two post lift.
Disconnect the battery.
Remove:
- the bonnet,
- the engine undertray.
Drain:
- the gearbox.
- the cooling circuit through the lower radiator
hose (radiator end).

Remove:
- the front wheels,
- the front right hand and left hand
mudguards.
98710R
10-14

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
E7J Engine
SPECIAL TOOLING
Mot. 1040-01 Dummy cradle for removing and
refitting the engine and
transmission assembly
Mot. 1202 Hose clip pliers
Front sub-frame mounting bolt 6
Rear sub-frame mounting bolt 11
Upper shock absorber cup mounting bolt 3
Wheel bolts 9
Brake caliper mounting bolt 3.5
Universal steering joint mounting bolt 3.5
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect:
- the battery,
- the relay plate and the engine connection unit
electrical connector,
98756R
- the connectors of the ignition module and the
HT coil wire,
- the oxygen sensor connector,
- the accelerator and clutch cables.
Drain:
- the cooling circuit,
- the engine if necessary,
- the gearbox (by removing the cover) if
necessary.
Remove:
- the earth strap,
- the air filter,
- the nut and the eccentric bolt (1) (remove
using a roll pin punch) from the steering shaft
yoke after having pushed the protector back.
97390-1R
10-19

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
K7M engine
/ AT
SPECIAL TOOLING
Mot. 1040-01 Dummy cradle for removing and
refitting the engine and
transmission assembly
Mot. 1202 Hose clip pliers
Mot. 1311-06 Tool for removing fuel pipes
Front sub-frame mounting bolt 6
Rear sub-frame mounting bolt 11
Upper shock absorber cup mounting bolt 3
Wheel bolts 9
Brake caliper mounting bolt 3.5
Universal steering joint mounting bolt 3.5
Engine mounting pad nut on front
left hand side member mounting 7.5
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Drain:
- the cooling circuit from the lower radiator
hose,
- the engine if necessary.
Remove:
- the front wheels,
- the left and right hand mudguards,
- the sub-frame-body tie rods,
- the brake calipers and attach them to the
body,
98710R
- the front bumper,
PRJ1002
10-24

Mot. 1040-01 Dummy cradle for removing and
refitting the engine and
transmission assembly
Mot. 1159 Tool for securing the engine on the
sub-frame
Mot. 1289-03 Fork for centring suspended engine
mounting limiter
Mot. 1273 Tool for checking belt tension
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F3R engine
Front sub-frame mounting bolt 6
Rear sub-frame mounting bolt 11
Upper shock absorber cup mounting bolt 3
Wheel bolts 9
Brake caliper bolt 3.5
Universal steering joint mounting bolt 3
Nut for mounting rubber mounting pad
on front left hand side member mounting 7.5
Bolt mounting front right hand suspended
engine mounting cover on engine 4
Mounting bolt for front right hand
suspended engine mounting
movement limiter 6
SPECIAL TOOLING
REMOVAL
Put the vehicle on a 2 post lift.
Remove the engine undertray.
Disconnect the battery.
Drain:
- the cooling circuit from the lower radiator
hose, water pump end,
98898R2
- the engine and gearbox if necessary.
TIGHTENING TORQUES (in daN.m)
10-29

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
TIGHTENING TORQUES (in daN.m)
Front sub-frame mounting bolt 6
Rear sub-frame mounting bolt 11
Upper shock absorber cup mounting bolt 3
Wheel bolts 9
Brake caliper bolt 3.5
Universal steering joint mounting bolt 3
Nut for mounting rubber mounting pad
on front left hand side member mounting 7.5
Bolt mounting front right hand suspended
engine mounting cover on engine 4
Nut mounting suspended engine
mounting cover on rubber mounting pad 4.5
Mot. 1040-01 Dummy cradle for removing and
refitting the engine and
transmission assembly
Mot. 1159 Tool for securing the engine on the
sub-frame
Mot. 1311-06 Tool for removing the fuel pipe
SPECIAL TOOLING
REMOVAL
Put the vehicle on a 2 post lift.
Remove the engine undertray.
Disconnect the battery.- the brake calipers and attach them to the
body,
- the sub-frame-body tie rods,98710R
Drain:
- the cooling circuit from the lower radiator
hose (radiator end),
- the engine and gearbox if necessary.
Remove:
- the front wheels,
- the right hand left hand mudguards,
10-36