Page 2417 of 2492
LOWER STRUCTURE
Acceleration sensor mounting
41SAcceleration sensor mounting
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the centre floor.
For standardisation purposes, the centre floor is
delivered by the Parts Department without the
acceleration sensor mounting.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone.
PARTS CONCERNED (thickness in mm):
1
2
3
4
5Acceleration sensor mounting
Front seat height adjuster
Front seat height adjuster reinforcement
Centre floor
Tunnel stiffener 1.2
1.5
1.5
1
1
41-16
Z
Page 2418 of 2492
LOWER STRUCTURE
Acceleration sensor mounting
41P
41-17
X1 = 122 mm
Z
Page 2419 of 2492
LOWER STRUCTURE
Central floor rear reinforcement
41Central floor rear reinforcement
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the centre floor or the
cross member.
For standardisation purposes, these parts are
delivered by the Parts Department without the rear
floor reinforcement.
In the operation described below, only descriptions of
the joints specific to the part concerned are given.
The information on the additional parts will be dealt
with in their appropriate chapters (see contents).
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part delivered alone.
PARTS CONCERNED (thickness in mm):
PRF4119
1
2
3
4
5Central floor rear reinforcement
Sill panel closure panel component
Cross member
Rear side member
Centre floor 1.5
1.8
1.2
1.5
1
641Z1-17951
41-18
AA
Page 2420 of 2492
LOWER STRUCTURE
Central floor rear reinforcement
41
41-19
AA
Page 2421 of 2492
UPPER FRONT STRUCTURE
Wing
42S
142UPPER FRONT STRUCTURE
Wing
INTRODUCTION
The replacement of this part is a basic operation for a frontal or side impact.
This is a detachable structure component.
It will first be necessary to remove:
– the side section of the scuttle panel grille (see section 55-G of the basic
Workshop Repair Manual),
– the front section of the valance, partially (see section 55-B),
– the front wing extender (see section 55-C),
– both sections of the front mudguard (see section 56-F of the basic
Workshop Repair Manual).
42-1
A
Page 2422 of 2492
UPPER FRONT STRUCTURE
Wing
42S
42-2
17564-1R
REMOVAL
Apply two strips of masking tape to the components around the wing, to
prevent the paintwork from being scratched during refitting.
Remove:
– nuts (A) and (B) (open the door),
– bolts (C), (D), (E) and nuts (F) and (G).
Separate the wing from the soundproofing mastic at (H) (see Technical
Note 412A).
REFITTING
NOTE: when refitting, re-apply sealant (detachable components sealing
mastic) between the mounting pads on the wing and the front pillar.
ADJUSTMENT
Fit all the mountings without tightening before beginning to adjust the play and
flush-fittings (see section 40).
REPAIR
REMINDER: see Technical Notes 392A and 473A for how to repair wings
(Noryl).
A
Page 2423 of 2492
UPPER SIDE STRUCTURE
Body side front section
43S
143UPPER SIDE STRUCTURE
Body side front section
INTRODUCTION
The replacement of this part is a basic operation
following a front side collision.
The method for replacing this part has not changed,
see basic Workshop Repair Manual.
For standardisation purposes, the front section of the
body side is delivered by the Parts Department without
the welded pins on the bottom section for mounting the
plastic fittings panels and without the drillings for
mounting the longitudinal flaps.
It will be necessary to fit the riveted pins (pin rivets)
and to make the drillings after the part has been
replaced.
The number of rivets required will depend on the
location of the cut on the sill panel.
The dimensions of the drillings to be carried out are
listed below.
43-1
F
Page 2424 of 2492
UPPER SIDE STRUCTURE
Body side front section
43S
43-2
17963R
A = Ø 2.5 mm
F