1995 RENAULT MEGANE SCENIC brake fluid

DESCRIPTIONPACKAGINGPART NUMBER
LUBRICANTS - CONSUMABLES
Packaging
04
•"CIRCUIT PLUS"
varnish for repairing heated screens
•
"CONTACT PLUS"
varnish for repairing rear screen supply termi-
nals
Bottle
Kit77 01 421 135
77 01 422 752
VARNISHES
BRAKES
• Brake fluid 0.5 litre bottleDOT 477 01 421 940
04-3

AD4 4
ELF RENAULT MATIC D2 (D20104)
or use: MOBIL ATF 220 (D20104 or D21412)
TEXAMATIC 4011
Automatic
transmission
VALUES AND SETTINGS
Capacity - Grades
07
3 .4 Manual gearboxComponents
Capacity in
litresGradeFeatures
JB1 3 .4
Brake circuit
Brake fluids must be approved by the Technical
DepartmentSAE J 1703
and DOT 3
All countries: TRANSELF TRX 75 W 80 W
( API GL5 or MIL-L 2105 C or D standards)
Normal : 0.7
ABS : 1
Fuel tankapproximately
60
Unleaded
petrol/diesel
JB3
Separate
reservoir
1.1
Cooling circuit
F3R
F8Q
E7J - K7M
GLACÉOL RX
(type D)
Only add coolant
7
7 .5
6
Power assisted
steeringELF RENAULT MATIC
D2 or
MOBIL ATF 220
07-4

MANUAL GEARBOX
Gearbox (Removal - Refitting)
21
Position the driveshaft with respect to the sun-
wheel, pivot the stub-axle carrier and engage the
driveshaft into the sunwheel using the shouldered
pin B.Vi. 31-01 in order to align the holes.IMPORTANT
Fit the bolt (V) and the starter motor centring do-
wel (D) correctly :
E and K engines
A chamfer on the leading edge of the sunwheel
makes it easier to fit new roll pins.
Seal the ends
(RHODORSEAL 5661).
Fill with fluids.
Fit the caliper mounting bolts with Loctite
FRENBLOC and tighten to the correct torque.
Press the brake pedal several times to bring the
pistons back into contact with the brake pads. E and K
engines
86070R3
Reconnect the speedo cable, ensuring that the clip
is the correct way round.
92108-1S
74937-4S
Tighten all nuts and bolts to the recommended
torques.
Fill the gearbox with oil.
21-12

MANUAL GEARBOX
Gearbox (Removal - Refitting)
21
Position the driveshaft with respect to the sun-
wheel, pivot the stub-axle carrier, engaging the
driveshaft into the sunwheel using the shouldered
pin B.Vi. 31-01 in order to align the holes. F engine
A chamfer on the leading edge of the sunwheel
facilitates makes it easier to fit new roll pins.
Seal the ends
(RHODORSEAL 5661).
Fill with fluids.
Fit the caliper mounting bolts with Loctite
FRENBLOC and tighten to the correct torque.
Press the brake pedal several times to bring the
pistons back into contact with the brake pads. F
engine
86070-1R1
Check the adjustments of the upper mountings
(refer to chapter 10).
Ensure that the movement limiter is mounted the
correct way round: the nuts should be fitted on
the exhaust pipe side.
92661S
74937-4S
Tighten all nuts and bolts to the recommended
torques.
Fill the gearbox with oil.
21-18

30
GENERAL
Parts to be renewed when they are removed / Brake fluid