Page 81 of 2492

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
- the front bumper,
PRJ1002
- the air inlet sleeve, the air filter and its
mounting,
- the exhaust downpipe,
- the two exhaust heat shields,
99612R
- the nut and eccentric bolt (1) (use a roll pin
punch) from the steering yoke after pushing
the protector back.
97390-1R
SPECIAL NOTES FOR VEHICLES FITTED WITH A
DRIVER’S AIRBAG
IMPORTANT
To avoid any risks of destroying the rotary switch
under the steering wheel, comply with the
following instructions:
• Before removing the steering column and the
rack, the steering wheel MUST be immobilised
with the wheels straight using a "steering
wheel locking" tool, throughout the whole
operation.
• Any doubts about whether the steering wheel
is centred means that the steering wheel will
have to be removed so that the centring
method described in section 88 "Airbag" can
be applied.
REMINDER: in this case, only qualified, trained
staff can carry out this operation.
- the gear control at the gearbox end (turn it
over and attach it to the exhaust pipe),
- the horn
- the expansion bottle (attach it to the engine)
- the earth strap
10-37
Page 82 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
Remove:
- the preheating unit (attach it to the engine),
- the fuel return union on the injection pump.
Disconnect:
- the fuel supply pipe on the diesel fuel filter
using tool Mot. 1311-06,
99461R
- the altimetric sensor connector,
- the relay plate and the engine connection unit
electrical connector,
98756R
- the feed wire for the preheating unit in the
scuttle panel and the starter feed.
98754R
- the heater hoses on the thermostat mounting,
98904R1
10-38
Page 83 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
- the pipes and connectors for the fast idle and
EGR solenoid valves,
- the brake servo pipe,
- the accelerator and clutch cables,
- the diesel fuel filter connector,
- the compressor feed wire (if fitted).
Remove:
- the cooling assembly (see section 19
"Radiator"),
- the alternator belt (see section 16),
- the compressor mounting bolts (if fitted) and
attach it to the front cross member.
NOTE: cut the base of tool Mot. 1159 to 30 mm.
99023R2
99024R2
Remove the oil filter.
Unclip the alternator wiring and move it to one
side.
Diagram for drilling tool Mot. 1159. (For
instructions on use, refer to page 10-40).
99028R
Fit tool Mot. 1159.
10-39
Page 84 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
99310R
Fit the bracket of tool Mot. 1159.
Remove:
- the oil radiator deflector and the oil radiator
and attach it to the engine,
99172R
- the suspended engine mounting cover on the
right hand side and the movement limiter.
99308R1
Fit a block between the gearbox and the left hand
sub-frame.
Remove the nut then using a copper hammer, tap
the stud to release it from the suspended
mounting on the left hand side.
99308R3
10-40
Page 85 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
92442R
PREPARATION OF TOOL MOT. 1040-01
Fit the wheel pins into the lower holes (G).
This is secured to the sub-frame by hooks (I).
98755R
Secure tool Mot. 1040-01 under the sub-frame.
PRJ1003
Remove:
- the upper shock absorber bolts,
- the four sub-frame mounting bolts.
Remove the engine and transmission assembly by
lifting the body.
99178S
Tie the spring - shock absorber units together
using rope.
Lower the 2 post lift until the tool comes into
contact with the floor.
10-41
Page 86 of 2492

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
REFITTING
The engine sub-frame can be easily aligned with
the bodywork by positioning the two
approximately 100 mm long threaded rods into
the two front mountings of the body sub-frame .
Refitting is the reverse of removal.
Tighten the sub-frame mounting bolts to a torque
of :
•6 daN.m at the front,
•11 daN.m at the rear.
If the vehicle has manual steering, position the
shock absorber mountings into the holes (A), and
into holes (B) for power assisted steering.
92114-1R
When the left and right hand suspended
mountings are refitted, remember to remove the
block under the gearbox and tool Mot. 1159
ADJUSTING THE LONGITUDINAL MOVEMENT
LIMITER
Slacken the two limiter bolts (E).
Insert the centring fork tool Mot. 1289-03 into the
openings in the suspended mounting cover.
Tighten the two limiter mounting bolts (E) to a
torque of6 daN.m.
Tighten all bolt, nuts and screws to the
recommended torques.
Fit the caliper mounting bolts using Loctite
FRENBLOC and tighten them to the correct
torque.
Press the brake pedal several times to bring the
pistons back into contact with the pads.
Fill:
- the cooling circuit and bleed it (see section
19),
- the engine and gearbox if required.
NOTE:
- check the steering shaft yoke spacer is in place
when refitting,
- ensure the heat shields are correctly
positioned.
99174-2R
10-42
Page 87 of 2492
ENGINE AND PERIPHERALS
Sump
10
SPECIAL TOOLING REQUIRED
T.Av. 476 Ball joint extractor
B.Vi. 31-01 Set of punches
EQUIPMENT REQUIRED
Engine support tool
(example : DESVIL M300)
Wheel bolt 9
Track rod end nut 3.5
Shock absorber base bolt 17
Engine tie bar bolt:
- on gearbox 6.5
- on sub-frame 7.5
Right hand engine mounting nut 4.5
Left hand gearbox mounting nut 4.5
Sump bolt 0.7 to 0.9
Oil pump bolt 2.5
Tie bar bolt on gearbox 2.5
Tie bar bolt on engine 5
TIGHTENING TORQUES (in daN.m)
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Drain the engine oil.
Remove:
- the catalytic converter,
- the front right hand wheel,
- the track rod end using tool
T.Av. 476,
- the upper shock absorber bolt and slacken the
lower bolt (do not remove it),
98746-1S
- the right hand driveshaft pin using tool B.Vi.
31-01, then tilt the hub to release the
driveshaft from the gearbox and attach it to
the steering,
- the engine - gearbox tie bar, E7J engine
10-43
Page 88 of 2492
PRJ1004
ENGINE AND PERIPHERALS
Sump
10
- nuts (1) for the engine and gearbox mounting
pads,
- nuts (2) for the tie bar mounting,
PRJ1001
- the air filter.
Fit the engine support tool, for example
DESVIL
M300.
98750R
Remove:
- the canister solenoid valve pipe,
98714R2
- the fuel pipes and their mounting on the right
hand side member and the inlet manifold,
- the power assisted steering reservoir,
- the speedo gear from the gearbox.
Lift the engine by the two lifting rings (4) and (5)
so that the three bolts (6) on mounting (7) may be
removed and then remove the engine by lifting it
out. E7J engine
10-44