Page 73 of 2492

Mot. 1040-01 Dummy cradle for removing and
refitting the engine and
transmission assembly
Mot. 1159 Tool for securing the engine on the
sub-frame
Mot. 1289-03 Fork for centring suspended engine
mounting limiter
Mot. 1273 Tool for checking belt tension
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F3R engine
Front sub-frame mounting bolt 6
Rear sub-frame mounting bolt 11
Upper shock absorber cup mounting bolt 3
Wheel bolts 9
Brake caliper bolt 3.5
Universal steering joint mounting bolt 3
Nut for mounting rubber mounting pad
on front left hand side member mounting 7.5
Bolt mounting front right hand suspended
engine mounting cover on engine 4
Mounting bolt for front right hand
suspended engine mounting
movement limiter 6
SPECIAL TOOLING
REMOVAL
Put the vehicle on a 2 post lift.
Remove the engine undertray.
Disconnect the battery.
Drain:
- the cooling circuit from the lower radiator
hose, water pump end,
98898R2
- the engine and gearbox if necessary.
TIGHTENING TORQUES (in daN.m)
10-29
Page 74 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F3R engine
98710R
Remove:
- the front wheels,
- the right and left hand mudguards,
- the brake calipers and the ABS sensors (attach
them to the body),
- the sub-frame-body tie rods,
- the exhaust downpipe (disconnect the oxygen
sensor),
- the horn,
- the two exhaust heat shields,
99612R
- the gear control at the gearbox end (turn it
over and attach it to the exhaust pipe),
- the front bumper,
PRJ1002
- the air inlet sleeve, the air filter and its
mounting.
Disconnect:
- the relay plate and the engine connection unit
electrical connector,
98756R
10-30
Page 75 of 2492

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F3R engine
- the accelerator and clutch cables,
- the heater hoses on the thermostat mounting.
Remove the battery mounting bracket.
Disconnect:
- the injection feed wire in the scuttle panel
and the starter feed,
98754R
- the brake servo pipe,
- the connectors for the fan, the relays, the
thermistor and the pressostat,
- the pipe on the canister,
- the upper and lower radiator hoses,
- the fuel return and supply pipes, unclipping
them from their mounting.Remove:
- the suspended engine mounting cap,
- the injection computer mounting and attach
it to the engine,
- the expansion bottle and attach it to the
engine,
- the absolute pressure sensor,
- the accessories belt (see section 11).
Unclip the power assisted steering reservoir.
Disconnect the compressor feed wire (if fitted).
Remove:
- the four mounting bolts for the air
conditioning compressor (if fitted), move it to
one side and attach it to the front of the
vehicle,
- the earth strap,
- the nut and eccentric bolt (1) (use a roll pin
punch) from the steering yoke after pushing
the protector back.
97390-1R
10-31
Page 76 of 2492
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F3R engine
SPECIAL NOTES FOR VEHICLES FITTED WITH A
DRIVER’S AIRBAG
IMPORTANT
To avoid any risks of destroying the rotary switch
under the steering wheel, comply with the
following instructions:
• Before removing the steering column and the
rack, the steering wheel MUST be immobilised
with the wheels straight using a "steering
wheel locking" tool, throughout the whole
operation.
• Any doubts about whether the steering wheel
is centred means that the steering wheel will
have to be removed so that the centring
method described in section 88 "Airbag" can
be applied.
REMINDER: in this case, only qualified, trained
staff can carry out this operation.
NOTE: cut the base of tool Mot. 1159 to 30 mm.
99023R2
99024R2
Diagram for drilling tool Mot. 1159. (For
instructions on use, refer to page 10-33).
99028R
Fit tool Mot. 1159.
10-32
Page 77 of 2492
99310R
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F3R engine
Fit the bracket of tool Mot. 1159 (water pipe
mounting bolt).
Remove the right hand suspended engine
mounting cover and the movement limiter.
99308R1
Fit a block between the gearbox and the left hand
sub-frame.Remove the nut then using a copper hammer, tap
the stud to release it from the suspended
mounting on the left hand side.
99308R3
92442R
PREPARATION OF TOOL MOT. 1040-01
Fit the wheel pins into the lower holes (G).
This is secured to the sub-frame by hooks (I).
10-33
Page 78 of 2492
98755R
ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F3R engine
Secure tool Mot. 1040-01 under the sub-frame.
PRJ1003
Attach the cooling assembly to the front face.
Remove the engine and transmission assembly by
lifting the body.
Tie the spring - shock absorber units together
using rope.
NOTE: for an operation requiring separation of
the engine - gearbox - sub-frame, note the
position of tool Mot. 1159 carefully. Lower the 2 post lift until the tool comes into
contact with the floor.
Remove:
- the upper shock absorber bolts,
- the four sub-frame mounting bolts.
99178S
10-34
Page 79 of 2492

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F3R engine
REFITTING
The engine sub-frame can be easily aligned with
the bodywork by positioning the two
approximately 100 mm long threaded rods into
the two front mountings of the body sub-frame .
Refitting is the reverse of removal.
Tighten the sub-frame mounting bolts to a torque
of :
•6 daN.m at the front,
•11 daN.m at the rear.
If the vehicle has manual steering, position the
shock absorber mountings into the holes (A), and
into holes (B) for power assisted steering.
92114-1R
When the left and right hand suspended
mountings are refitted, remember to remove the
block under the gearbox and tool Mot. 1159
ADJUSTING THE LONGITUDINAL MOVEMENT
LIMITER
Slacken the two limiter bolts (E).
Insert the centring fork tool Mot. 1289-03 into the
openings in the suspended mounting cover.
99166-1R
Tighten the two limiter mounting bolts (E) to a
torque of6 daN.m.
Tighten all bolt, nuts and screws to the
recommended torques.
Fit the caliper mounting bolts using Loctite
FRENBLOC and tighten them to the correct
torque.
Press the brake pedal several times to bring the
pistons back into contact with the pads.
Fill:
- the cooling circuit and bleed it (see section
19),
- the engine and gearbox if required.
NOTE:
- check the steering shaft yoke spacer is in place
when refitting,
- ensure the heat shields are correctly
positioned.
10-35
Page 80 of 2492

ENGINES AND PERIPHERALS
Engine and transmission assembly
10
F8Q engine
TIGHTENING TORQUES (in daN.m)
Front sub-frame mounting bolt 6
Rear sub-frame mounting bolt 11
Upper shock absorber cup mounting bolt 3
Wheel bolts 9
Brake caliper bolt 3.5
Universal steering joint mounting bolt 3
Nut for mounting rubber mounting pad
on front left hand side member mounting 7.5
Bolt mounting front right hand suspended
engine mounting cover on engine 4
Nut mounting suspended engine
mounting cover on rubber mounting pad 4.5
Mot. 1040-01 Dummy cradle for removing and
refitting the engine and
transmission assembly
Mot. 1159 Tool for securing the engine on the
sub-frame
Mot. 1311-06 Tool for removing the fuel pipe
SPECIAL TOOLING
REMOVAL
Put the vehicle on a 2 post lift.
Remove the engine undertray.
Disconnect the battery.- the brake calipers and attach them to the
body,
- the sub-frame-body tie rods,98710R
Drain:
- the cooling circuit from the lower radiator
hose (radiator end),
- the engine and gearbox if necessary.
Remove:
- the front wheels,
- the right hand left hand mudguards,
10-36