Page 1961 of 2492

UPPER REAR STRUCTURE
Rear quarter panel lining assembly
PRE4419
44F
INTRODUCTION
The replacement of this part is a complementary
operation to a complete wing panel.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- outer wheel arch,
- seat mounting reinforcement,
- connecting bracket,
- rear end pillar lining assembly,
- upper corner reinforcement assembly.
PARTS CONCERNED (thickness in mm) :
1Body side lining 0.7
2Rear quarter panel lining 0.7
3Centre pillar lining 1.2
4Front sill closure panel 1.5
5Rear sill closure panel 0.8
6Rear inner wheel arch 0.8
7Seat belt mounting reinforcement 1.5
8Stretcher lining 1.2
9Rear floor base 0.8
10Rear floor 0.7
11Rear end pillar lining 1
12Rear end pillar lower reinforcement 1
or
NOTE : to avoid replacing the part located behind
the sill panel, cut the front lower section of the li-
ning, see section (C) in the diagram below.
44-21
Page 1962 of 2492
UPPER REAR STRUCTURE
Rear quarter panel lining assembly
254f01-15375
44F
or
A
CAW13602R7
1
6
5
B
C
CAA11537-1R1a
1
1
D
TOA14581R4
1
5
CAA11536-1R2
15
44-22
Page 1963 of 2492
UPPER REAR STRUCTURE
Rear quarter panel lining assembly
254f04-15371
44F
E
TOD14617R4
1
4
5
F
CAA11536R2
13
G
Ga
CAQ11697-2R1a
7 14
TOA14581R3
1
5
44-23
Page 1964 of 2492
UPPER REAR STRUCTURE
Rear quarter panel lining assembly
254f03-15372-1
44F
254f02-15373
H
CAA11537R2
1 8
I
TOB14593R5
111
J
CAW13603-2R8
111
12
44-24
Page 1965 of 2492
UPPER REAR STRUCTURE
Rear quarter panel lining assembly
44F
K
CAT13319-1R2
112
L
CAA11538-1R4
19
M
CAA11538-1R4
110
N
CAA11538-1R2
1 6
O
CAQ11697R6a
1
6
P
CAT13319-1R2
211
44-25
Page 1966 of 2492
UPPER REAR STRUCTURE
Rear quarter panel lining assembly
44F
Q
TOK14646-3R5
1 11
2
44-26
Page 1967 of 2492

UPPER REAR STRUCTURE
Outer wheel arch
PRE4421
44G
INTRODUCTION
This part can be replaced in two ways:
• by part section A , complementary to the rear
end pillar,
• by part section B , complementary to the wing
panel.
The method described only contains descriptions
of joints specific to the part concerned. Joints with
complementary parts are not included.
These are dealt with in their respective section (re-
fer to the contents page).
COMPOSITION OF PART FROM PARTS
DEPARTMENT
Part assembled with:
- outer wheel arch,
- seat mounting reinforcement,
- connecting bracket,
- rear end pillar lining assembly,
- upper corner reinforcement assembly.
PRE4420
SECTION A : complementary to rear end pillar
reinforcement.
SECTION B : complementary to rear wing panel.
PARTS CONCERNED (thickness in mm) :
1Body side lining 0.7
2Rear quarter panel lining 0.7
3Rear end pillar lining 1
4Rear floor base 0.8
5Rear floor 0.7
6Rear inner wheel arch 0.8
7Seat belt mounting reinforcement 1.5or
44-27
Page 1968 of 2492
UPPER REAR STRUCTURE
Outer wheel arch
COMPLEMENTARY TO REAR END PILLAR
REINFORCEMENT
254g01-15372
44G
or
A
CAP11696-1R4
2
1
1
B
CAA11536-3R7
1
C
CAT13321-1R7
1 2 3
D
CAA11538-1R1
122
44-28