1995 RENAULT MEGANE SCENIC window

TOP AND FRONT OF ENGINE
Timing belt
11F8Q ENGINE
99309R2
Remove:
- the suspended mounting cover and the move-
ment limiter,- the lower timing casing (1),
- the alternator drive belt (see section 16
"Removing the alternator"),
Turn the crankshaft to position the camshaft ti-
ming reference mark in the timing window.
99176G
89120-2S
11-8

MECHANISMS OF OPENINGS
OTHER THAN SIDE DOORSPages
Contents
SIDE DOOR MECHANISMS
GLAZING51
54
Mechanisms and
accessories
52
EXTERIOR ACCESSORIES
UPPER INTERIOR ACCESSORIES56
58
51-1
51-4 Front door window mechanism
Quarter light mechanism
52-1
52-7
52-10
52-13
52-16 Complete manual or
electrohydraulic hood
Front hood locks
Complete hydraulic system
Hydraulic system (pipes)
Hydraulic system reservoir
54-1
54-5 Front door windows
Quarter light
56-1 Exterior mirror
58-1 Road box

SIDE DOOR MECHANISMS
Front door window mechanism
Remove the window mechanism.
51
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
After removing the interior trim, the side impact
bar and the window, compress the window
mechanism rings.
PRE5101
Disconnect the motor connector.
Remove the window mechanism mounting bolts.
12279R
12280S
51-1

SIDE DOOR MECHANISMS
Front door window mechanism
Turn the motor shaft until the mounting bolt (3) is
accessible.
Remove the mounting bolts.
51
PRE5103
CC C C
HH H H
AA A A
NN N N
GG G G
II I I
NN N N
GG G G

TT T T
HH H H
EE E E

MM M M
OO O O
TT T T
OO O O
RR R R
After removing the window mechanism, mark the
position of the stop (1).
Remove the stop.
Open the motor cover mounting plates (2) and
remove the motor.
Detach the toothed ring.
Remove the mounting bolt (4).
12286R
12285R
12284R
51-2

SIDE DOOR MECHANISMS
Front door window mechanism
51
RR R R
EE E E
FF F F
II I I
TT T T
TT T T
II I I
NN N N
GG G G
Secure the motor and engage the toothed wheel.
Connect the motor and operate the window
mechanism.
Position the stop (1) at the marks and tighten it.
Refit the window mechanism - window assembly.
The tightening torque for all of the bolts is 8 N.m.
AA A A
DD D D
JJ J J
UU U U
SS S S
TT T T
MM M M
EE E E
NN N N
TT T T
See section 54.
51-3

SIDE DOOR MECHANISMS
Quarter light mechanism
- the window .
AA A A
DD D D
JJ J J
UU U U
SS S S
TT T T
MM M M
EE E E
NN N N
TT T T
See section 54
51
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
After removing the seat, the rear bench seat
backrest, the interior trim and the window,
disconnect the motor connector.
PRE5102
Remove:
- the window mechanism mountings (1),
12295R
12296S
51-4

GLAZING
Front door window
- the window mounting bolts (3).
Tilt the window towards the rear and remove it.
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L

OO O O
FF F F

TT T T
HH H H
EE E E

RR R R
EE E E
AA A A
RR R R

SS S S
LL L L
II I I
DD D D
EE E E
RR R R
54
PRE5401
RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
After removing the interior trim,
Remove the slider blanking piece and mountings
(4). remove:
- the side impact bar bolts (1) ,
- the interior weatherstrip,
- the rear guide shoe bolt (2) ,
12276R
12281R 12277-1R
54-1

GLAZING
Front door window
AA A A
DD D D
JJ J J
UU U U
SS S S
TT T T
II I I
NN N N
GG G G

TT T T
HH H H
EE E E

WW W W
II I I
NN N N
DD D D
OO O O
WW W W
SS S S
The hood must be folded for the fixed window,
two operators are required to adjust the movable
window.
The door must be adjusted correctly and the
upper movable window stops must be in the
uppermost position.
54
FF F F
II I I
XX X X
EE E E
DD D D

WW W W
II I I
NN N N
DD D D
OO O O
WW W W
Remove the window mounting bolts (5) and the
window pillar mounting bolts (6).
Tilt the assembly (window/pillar) and remove the
window.
FF F F
II I I
XX X X
EE E E
DD D D

WW W W
II I I
NN N N
DD D D
OO O O
WW W W
With the door closed (1st notch), position the
pillar at dimension A = 30 mm high and B = 6
mm from the edge of the windscreen aperture
seal.
12281-1R
12278S
12438R
54-2