2007 MITSUBISHI LANCER EVOLUTION Service Repair Manual

BODY -Doors42-37
Rear door

Rod positionTerminal No.Rod operationp
23
p
LOCKLOCK to UNLOCK
UNLOCKUNLOCK to LOCK

Rod positionTerminal No.Rod operationp
23
p
LOCKLOCK to UNLOCK
UNLOCKUNLOCK to LOCK
DOOR LOCK KEY CYLINDER SWITCH CONTINUITY
CHECK
Switch positionTerminal No.p

123123
LOCK
OFF
UNLOCK

BA

View ALock
Unlock

View B
UnlockLock

BODY -Doors42-38
WINDOW GLASS RUNCHANNEL AND DOOR OPENING
WEATHERSTRIP
REMOVAL AND INSTALLATION
2
5
43

1
Sectional view of
clip position Sectional view of clip
position
Section A - A
Door
5
A
A
Door inner opening weatherstrip
removal steps
DScuff plate (Refer to GROUP 52A.)
DCowl side trim (Refer to GROUP
52A.)
DCenter pillar lower trim (Refer to
GROUP 52A.)
1. Door inner opening weatherstrip
Door outer opening weatherstrip
removal
AA""AA2. Door outer opening weatherstrip
Door window glass runchannel
removal
3. Door window glass runchannelDoor beltline inner weatherstrip
removal steps
DDoor trim (Refer to P.42-27.)
4. Door beltline inner weatherstrip
Door beltline molding removal
steps
DOutside mirror (Refer to GROUP
51.)
DDoor window glass (Refer to
P.42-32.)
5. Door beltline molding

BODY -Doors42-39
Sectional view of
clip positionSectional view of
clip position
5
4 3
21

Section A - A
Door
6
A
A
6
BB
Section B - B
Door
23
Door inner opening weatherstrip
removal steps
DScuff plate (Refer to GROUP 52A.)
DCenter pillar lower trim (Refer to
GROUP 52A.)
1. Door inner opening weatherstrip
Door outer opening weatherstrip
removal steps
2. Retainer weatherstrip
AA""AA3. Door outer opening weatherstrip
Door window glass runchannel
removal
4. Door window glass runchannelDoor beltline inner weatherstrip
removal steps
DDoor trim (Refer to P.42-27.)
5. Door beltline inner weatherstrip
Door beltline molding removal
steps
DDoor window glass (Refer to
P.42-32.)
DStationary glass (Refer to P.42-32.)
6. Door beltline molding
REMOVAL SERVICE POINT
AA"DOOR OUTER OPENING WEATHERSTRIP
REMOVAL
Make a tool as shown and remove the weatherstrip from
the door panel.15mm
4mm
8mm
Thickness
1mm

BODY -Doors42-40
INSTALLATION SERVICE POINTS
"AADOOR OUTER OPENING WATHERSTRIP
INSTALLATION
The clip colour identifies the left and right weatherstrips so
be sure to use the colours as install correctly.
Applicable sideIdentification colour
Right doorPink
Left doorNatural (White)

BODY -Trunk lid42-41
TRUNK LID
REMOVAL AND INSTALLATION
2
34 56
7 89 10
111
12A
A
B
B5 5
99
14Measure of
length mm
15
4 9
12
8.9±1.9 N·m
Section A - A
Section B - B
Trunk lid weatherstrip removal
steps
DRear end trim (Refer to
GROUP 52A.)
"BA1. Trunk lid weatherstrip
Trunk lid release cable and trunk
lid release handle removal steps
DTrunk rear side trim (Left side)
(Refer to GROUP 52A.)
DRear seat (Refer to GROUP 52A.)
DCenter pillar lower trim (Refer to
GROUP 52A.)
DCowl side trim
DAccelerator pedal stopper
2. Trunk lid release handle
3. Trunk lid release cable
Trunk lid striker removal steps
DRear end trim (Refer to
GROUP 52A.)4. Trunk lid striker
Trunk lid panel removal steps
5. Trunk lid bumper
6. Trunk lid lock cylinder
7. Trunk lid latch assembly
8. Trunk lid hinge mounting bolt
9. Trunk lid panel assembly
Trunk lid latch assembly removal
7. Trunk lid latch assembly
Trunk lid hinge removal steps
DRear shelf trim
DRear seat (Refer to GROUP 52A.)
9. Trunk lid panel assembly
AA""AA10. Trunk lid torsion bar (Right side)
AA""AA11. Trunk lid torsion bar (Left side)
12. Trunk lid hinge

BODY -Trunk lid42-42
Grease application area
67
2
REMOVAL SERVICE POINT
AA"TRUNK LID TORSION BAR REMOVAL
Insert the tire lever into the torsion bar, and then pull upward
the tire lever to remove the torsion bar as shown in the
illustration.
NOTE
As the left and right trunk lid torsion bars are crossed at
the center, first remove the front trunk lid torsion bar at
the center.
INSTALLATION SERVICE POINTS
"AATRUNK LID TORSION BAR INSTALLATION
Install the trunk lid torsion bar by the following procedure.
1. Ensure that there is the identification color at the center
of the trunk lid torsion bar.
Trunk lid torsion barIdentification color
Left side-
Right sideRed
Caution
As the trunk lid torsion bar (Right side) is painted
with differentiation color in the middle to differentiate
between RH and LH, be careful when installing.
2. Install the trunk lid torsion bar (Left side) as follows.
(1) For terminal A, insert the trunk lid hinge (Left side)
into the fixed hole B
(2) For terminal C, touch the trunk lid hinge (Right side)
against portion E.
(3) For terminal D, insert the trunk lid hinge (Right side)
into portion F until portion G while twisting with the
tool such as a tire lever, etc.
(4) For terminal C, set the trunk lid hinge (Right side)
at portion H while twisting with the tool such as a
tire lever etc.
3. Install the trunk lid torsion bar (Right side) in the same
way as above.
Trunk lid torsion bar
Tire lever
Tire lever
D
Trunk lid torsion
bar
H
Identification
color
Trunk lid torsion bar
(Right side)
Trunk lid torsion bar
(Left side) Trunk lid hinge (Left side)
A
BC
D
Trunk lid hinge
(Right side)
C
F
G
E
Trunk lid torsion bar (Left side)

BODY -Trunk Lid42-43
"BATRUNK LID WEATHERSTRIP INSTALLATION
aligning the trunk lid weatherstrip marking section at the body
center to install.
INSPECTION
TRUNK LID LATCH SWITCH CONTINUITY CHECK
Switch positionTerminal No.p
1Earth
Latch open
Latch closed
Marking
section
Joint
section
Trunk lid latch
assembly

NOTES